ignition RENAULT SCENIC 2010 J95 / 3.G Engine And Pheripherals DCM 1.2 Injection Repair Manual

13B-158
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET415
CONTINUED 4
STATUS 8Automatic gearbox in defect mode.
Status ET415 becomes STATUS 8 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the automatic gearbox is in
defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test (see 88B, Multiplexing), then run fault finding on the
automatic gearbox computer.
Deal with any present or stored faults (see 23A, Automatic gearbox).
Clear the fault memory of the automatic gearbox computer by applying command RZ001
Fault memory.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If the specification STATUS 8 is still present, contact Techline.
STATUS 9Vehicle speed monitoring
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Test the multiplex network (see 88B, Multiplexing), then run fault finding on the ABS
computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system).
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If the specification STATUS 9 is still present, contact Techline.

13B-159
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET415
CONTINUED 5
STATUS 10Monitoring by injection computer
Status ET415 becomes STATUS 10 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and if the injection computer
detects a fault anywhere in the engine management system, or an engine speed that is
too high or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Test the multiplex network (see 88B, Multiplexing), then run fault finding on the injection
computer.
Deal with present or stored faults.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".

13B-160
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 50
ET563FLOW CAPACITY FUNCTION
STATUS DEFINITIONACTIVE: This status indicates that the flow capacity function is active.
INACTIVE: This status indicates that the flow capacity function is inactive.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
INACTIVE
OR ACTIVEIf there is a fault, use the interpretation of fault DF130 "Flow capacity function".
DCM1.2_V50_ET563

13B-161
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET637NEW PUMP CHAMBER FILLING
STATUS DEFINITIONCOMPLETED: This status indicates that the new pump chamber filling has been
completed.
NOT COMPLETED: This status indicates that the new pump chamber filling has
not been completed.
Conformity check: Engine stopped, ignition on or engine running.
COMPLETED
OR
NO
COMPLETEDThe actuator AC212 "New pump chamber filling" must be controlled before the engine
start following the replacement of the high pressure pump (see NT5011A "Repriming
Delphi high pressure pumps on K9K engines").
DCM1.2_V48_ET637/DCM1.2_V4C_ET637/DCM1.2_V50_ET637/DCM1.2_V54_ET637/DCM1.2_V58_ET637/DCM1.2_V5C_ET637

13B-162
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONINACTIVE: This status indicates that no button has been pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
SUSPEND: This status indicates that the 0 is pressed.
RESUME: This status indicates that the R button is pressed.
Conformity check: Engine stopped, ignition on or engine running.
INACTIVEStatus ET703 becomes INACTIVE when none of the cruise control/speed limiter buttons
are pressed. These buttons are located on the steering wheel.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display INACTIVE,
●check the condition of the cruise control/speed limiter ± button and the condition
of its connector.
●check the condition of the cruise control/speed limiter R/0 button and the
condition of its connector.
Repair if necessary.
INCREASEStatus ET703 becomes INCREASE when the + cruise control/speed limiter button is
pressed. This button is on the steering wheel, on the left-hand side.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display INCREASE, check the condition of the cruise control/
speed limiter
± button, and the condition of its connector. Repair if necessary.
Measure the resistance of the button between connections 86M and 86G while
pressing on the + button.
If the resistance is not approximately 300 Ω, check the continuity of the connection when
the button is in the rest position.
If there is continuity, replace the
± control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).
DCM1.2_V48_ET703/DCM1.2_V4C_ET703/DCM1.2_V50_ET703/DCM1.2_V54_ET703/DCM1.2_V58_ET703/DCM1.2_V5C_ET703

13B-163
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703
CONTINUED 1
DECREASEStatus ET703 becomes DECREASE when the - button of the cruise control/speed limiter
is pressed. This button is on the steering wheel, on the left-hand side.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not display DECREASE, check the condition of the cruise control/
speed limiter
± button, and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the - button.
If the resistance is not approximately 100 Ω, check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the
± control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter "0" button is
pressed. This button is located on the steering wheel, to the right.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not become SUSPEND, check the condition of the cruise control/
speed limiter "R/0" button and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the 0 button.
If the resistance is not about 0 Ω, replace the R/0 control button (see MR 364 (Mégane
II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR
417 (Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal
- Refitting).
If there is continuity, replace the R/0 control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).

13B-164
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET703
CONTINUED 2
RESUMEStatus ET703 becomes RESUME when the cruise control/speed limiter "R" button is
pressed. This button is located on the steering wheel, to the right.
To be able to remove the driver's airbag and carry out the measurements safely
(see 88C, Airbag and pretensioners).
If status ET703 does not change to RESUME, check the condition of the cruise control/
speed limiter R/0 button, and the condition of its connector.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the button between connections 86M and 86G while
pressing on the R button.
If the resistance is not approximately 900 Ω, check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the R/0 control button (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 83D, Cruise control, Steering wheel switch: Removal -
Refitting).

13B-165
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
Note:
Statuses ET704 and ET705 should change status at the same time. In the event of inconsistency, refer to the
interpretation of fault DF050 Brake switch circuit.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVE
OR
INACTIVEIf the brake lights are working, check the continuity and the absence of interference
resistance between the following connections:
–5A between components 160 and 120,
–BPT between components 160 and 645 (for Mégane II, Scénic II, Modus and Clio III),
–BPT2 between components 160 and 645 (for Kangoo 2),
–AP10 between components 160 and 1016 (for New Twingo),
–65A between components 160 and 645 (vehicle without ESP),
–65G between components 160 and 645 (vehicle with ESP).
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
–the condition and fitting of the brake switch,
–the condition and conformity of the brake lights fuse,
the conformity of the values in the following table:
DCM1.2_V48_ET704/DCM1.2_V4C_ET704/DCM1.2_V50_ET704/DCM1.2_V54_ET704/DCM1.2_V58_ET704/DCM1.2_V5C_ET704/
DCM1.2_V48_ET705/DCM1.2_V4C_ET705/DCM1.2_V50_ET705/DCM1.2_V54_ET705/DCM1.2_V58_ET705/DCM1.2_V5C_ET705

13B-166
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET704
ET705
CONTINUED
ACTIVE
OR
INACTIVE
CONTINUEDContinuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT or BPT2SP17 and 65G (with ESP)
SP17 and 65A (without
ESP)
Switch released
(Brake pedal depressed)SP17 and 65G (with ESP)
SP17 and 65A (without
ESP)5A and BPT or BPT2
Only for New TwingoContinuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and AP10 65A and AP10
Switch released
(Brake pedal depressed)65A and AP10 5A and AP10
If the values obtained are not correct, replace the brake switch (see MR 417 Mechanics,
37A, Mechanical component controls, Brake light Switch: Removal - Refitting).

13B-167
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 54
ET741OPTIONAL VEHICLE SPEED RESTRICTION
STATUS DEFINITIONACTIVE: This status indicates that the optional speed limiting function is active.
INACTIVE: This status indicates that the optional speed limiting function is inactive.
NOTESSpecial note:
This status indicates whether the vehicle speed restriction is a customer option, using
command SC040 Speed limiter.
This status is valid only on Kangoo 2
Conformity check: Engine stopped, ignition on or engine running.
"ACTIVE"Vehicle speed restricted using command SC040 Speed limiter. See the interpretation
of parameter PR879 Maximum speed authorized to find the configured speed
restriction.
"INACTIVE"The vehicle has no optional speed restriction.
DCM1.2_V54_ET741