RENAULT SCENIC 2010 J95 / 3.G Engine Compartment Connection Unit User Guide
Manufacturer: RENAULT, Model Year: 2010, Model line: SCENIC, Model: RENAULT SCENIC 2010 J95 / 3.GPages: 56
Page 11 of 56
87G - 11
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87G
V6 MR-372-J84-87G000$330_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
NOTESIgnition on, engine off.
No. ConfigurationRelated
configuration
readingNote:
CF001ALTERNATOR TYPE:
TG11 110 VALEO
SG12 VALEO
LIE8 150 BOSCH
SG15L VALEO
MELCO 8GMLC001Find out which type of
alternator is fitted on the
vehicle then confirm.
(MELCO = Mitsubishi
Electronics Corporation)
No. Different settings Note:
VP003 ENTERING THE VIN:Find out what the vehicle VIN is then confirm.
MR-372-J84-87G000$330_eng.mif
Page 12 of 56
87G - 12
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Summary of faults
87G
V6 MR-372-J84-87G000$396_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Summary of faults
Tool fault Associated DTC Diagnostic tool title
DF002 9210 HIGH SPEED FAN RELAY CONTROL CIRCUIT
DF005 920E INTERNAL ELECTRONIC FAULT
DF009 920D + IGNITION CIRCUIT
MR-372-J84-87G000$396_eng.mif
Page 13 of 56
87G - 13
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87G
V6 MR-372-J84-87G000$462_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
DF002
PRESENT
HIGH SPEED FAN RELAY CONTROL CIRCUIT
CC.1 : Short circuit to +12 V
NOTESSpecial notes:
The function is inhibited when the fault is present.
Reactivating the function via a new ignition request.
Measure the resistance between tracks 1 and 2.
If the resistance is not 65 ΩΩ Ω Ω
± 10 ΩΩ Ω Ω
, replace the relay.
Take the relay out and make sure that it is insulated from the +12 V for the connection:
UPC connector PPM2 track 2 Track 2 of the fan relay connector
Repair if necessary.
If the fault is still present, check for the absence of +12 V on track 2 of the UPC connector PPM2.
If +12 V is present, contact the Techline.
AFTER REPAIRClear the computer memory.
Turn the ignition off and then on again, then run a new check using the fault finding tool
MR-372-J84-87G000$462_eng.mif
Page 14 of 56
87G - 14
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87G
V6 MR-372-J84-87G000$462_eng.mif
UPC
Vdiag No.: 44
D F005
PRESENT
INTERNAL ELECTRONIC FAULT
DEF : Internal electronic fault
NOTESNone.
Disconnect the battery for 30 seconds then reconnect it.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer memory.
Turn the ignition off and then on again, then run a new check using the fault finding tool.
Page 15 of 56
87G - 15
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87G
V6 MR-372-J84-87G000$462_eng.mif
UPC
Vdiag No.: 44
DF009
PRESENT
+ APC CIRCUIT
DEF : Consistency
NOTESNone.
Check the voltage of the battery.
Check that ET026 + ignition status is consistent
Check the condition of the fuses on the battery positive terminal.
Repair if necessary.
Check the status and the connection of the + battery on the UPC mounting and on the P2 connector.
Repair if necessary.
With the ignition turned off, check that there is no +12 V supply on track 6 of UPC connector PPM2
If the +12 V feed is present, disconnect the following fuses one by one in order to isolate the faulty track:
–fuse 5C (track 6 connector PPM2),
–fuse 5D (track 1 connector PEH),
–fuse 5E (track 10 connector PPH2),
–fuse 5F (track 11 connector PPH2),
–fuse 5G (track 7 connector PPM2),
–fuse 5H (track 10 connector PPM2).
Using an electrical diagram, check the insulation against +12 V, of the connection between the track which
the UPC detected as faulty and the computers or consumers linked to this track.
With the ignition on, check for the presence of +12 V on one of the following UPC tracks:
–track 1 of connector PEH
–tracks 6, 7 and 10 of connector PPM2
–tracks 10 and 11 of connector PPH2
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer memory.
Turn the ignition off and then on again, then run a new check using the fault finding tool.
Page 16 of 56
87G - 16
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
MAIN SCREEN
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Charging circuitET001:Battery warning
lightLIT
In the event of a fault, refer to
the relevant fault finding
method. 2Oil pressure
contactET027:Oil pressure
contactCLOSED
3GearboxET004:Reverse gear
engagedYES
NO
MR-372-J84-87G000$528_eng.mif
Page 17 of 56
87G - 17
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
KEYLESS VEHICLE: Starting the engine
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1GearboxET004:Reverse gear
engagedYES
NO
In the event of a fault, refer to
the relevant fault finding
procedure. ET005:Manual gearbox
leverNEUTRAL
OUT OF NEUTRAL
NOT SUPPORTED, if
the vehicle is fitted with
an automatic gearbox
2StartingET010:Conditions for
engine start
satisfied.YES, if the conditions
for engine start have all
been satisfied and
after pressing the start
button
NO, if the engine start
conditions have not all
been satisfied or if the
engine start button has
not been pressed
Page 18 of 56
87G - 18
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
AIR CONDITIONING: Heating
AIR CONDITIONING: Cold loop
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1StartingPR010:AlternatorIn %
The value must be
fixed and greater than
98%
Refer to the relevant fault
finding procedure in the
event of a fault.
AC011:Rear
windscreen
de-icingThe rear window
heating resistors and
the door mirrors (if the
vehicle is fitted with
heated door mirrors)
must be supplied with
power and heated.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Fan assemblyAC009:Low speed fan
unitIt must be possible to
hear the fan running at
low speed.
Refer to the relevant fault
finding procedure in the
event of a fault. AC010:High speed fan
unitIt must be possible to
hear the fan running at
high speed
This command cannot
be used on vehicles
not fitted with climate
control
2Air conditioningAC008:Compressor
commandThe compressor clutch
must be heard (the
compressor command
is not permitted when
the engine is running)
Page 19 of 56
87G - 19
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
WIPERS: Wiper power
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Park positionAC012:Windscreen
wiper park
position testThe front windscreen
wiper must run for a
single sweep and
return to its initial
position.
Refer to the relevant fault
finding procedure in the
event of a fault. 2Wiper protectionET002:Front
windscreen
wiper protectionINACTIVE
3WipersAC005:Low-speed
windscreen
wiperThe windscreen wiper
must work at low
speed.
AC006:High-speed
windscreen
wiperThe windscreen wiper
must work at high
speed.
Page 20 of 56
87G - 20
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
LIGHTING: Lighting power
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1LightingAC003:Side lightsThe front and rear side
lights and the number
plate lights as well as
the controls and
switches in the
passenger
compartment must
light up.
Refer to the relevant fault
finding procedure in the
event of a fault.
AC002:Dipped beam
headlightsThe dipped beam
headlights must come
on.
AC001:Main beam
headlightsThe main beam
headlights must come
on.
AC004:Front fog lightsThe front fog lights
must come on.