Df239 RENAULT SCENIC 2011 J95 / 3.G Air Bag ACU4 - Seat Belt Pretensioners Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2011, Model line: SCENIC, Model: RENAULT SCENIC 2011 J95 / 3.GPages: 68, PDF Size: 0.38 MB
Page 18 of 68
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Summary table of faults
88C - 18
88C
V3
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Summary table of faults
AIRBAG ACU4
Vdiag: 04
Tool fault Associated DTC Diagnostic tool heading
DF001
DF002
DF010
DF028
DF034
DF039
DF040
DF051
DF052
DF053
DF060
DF065
DF066
DF067
DF068
DF069
DF070
DF071
DF072
DF074
DF075
DF077
DF091
DF187
DF193
DF194
DF210
DF214
DF232
DF239
DF240
DF2419080
9042
9040
9041
907E
9035
9036
9035
9036
9031
9050
9031
900E
900D
900C
900A
9009
9008
9007
9006
9005
900B
9034
9044
907C
907F
9014
9034
9051
9017
9001
9002Computer
Computer supply voltage
Fault warning light circuit
Passenger's airbag status warning light circuit
Computer locked
Driver's side sensor circuit
Passenger's side sensor circuit
Driver's side sensor configuration
Passenger side sensor configuration
Driver's seat position sensor
Multiplex network
Driver's front seat position sensor circuit
Passenger's rear side air bag circuit
Driver's rear chest side airbag circuit
Passenger's front side airbag circuit
Passenger's curtain side airbag circuit
Driver's head side airbag circuit.
Driver's front airbag circuit 2
Driver's front airbag circuit 1
Passenger's front airbag circuit 2
Passenger's front airbag circuit 1
Driver's front side airbag circuit
airbag locking switch circuit
Trigger lines configuration
Change of status of passenger airbag locking
Computer to be replaced following impact
Front buckles pretensioner circuit
Airbag lock switch configuration
Driver's seat belt buckle sensor circuit
Rear seat belt retractors circuit
Driver's seat-cushion / seat lap belt circuit
Passenger's seat-cushion / seat lap belt circuit
ACU4 Vdiag04 J84 1.0
MR-372-J84-88C000$060.mif
Page 60 of 68
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Fault Interpretation
88C - 60
88C
V3 MR-372-J84-88C000$072.mif
AIRBAG ACU4
Vdiag: 04
DF239
PRESENT
REAR SEAT BELT RETRACTORS CIRCUIT
CC : Short circuit
CO : Open circuit
CC.1 : Short circuit to + 12 V
CC.0 : Short circuit to earth
1.DEF : Configuration
NOTESIf 1.DEF, check and adjust the computer configuration.
Special notes: the rear seat belt retractors are serially wired.
Never do measuring on the trigger lines with any tool other than CLIP or XRBAG.
Use the 64-track (Elé. 1717) adapter to work on the computer connector.
CO - CC
NOTESSpecial notes: Correct the trigger line configuration if the
vehicle is not fitted with rear seat-belt retractors.
Lock the computer.
Switch off the ignition and check that the ignition module of the rear seat belt retractor, driver's side is correctly
connected.
Disconnect the ignition module of the retractor and connect a dummy ignition module to the ignition module
connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the rear seat belt retractor, driver's side, if the fault becomes stored (fault no longer declared present).
Switch off the ignition and check that the ignition module of the rear seat belt retractor, passenger's side is
correctly connected.
Disconnect the ignition module of the retractor and connect a dummy ignition module to the ignition module
connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the passenger's side rear seat belt retractor if the fault becomes stored (fault no longer declared
present).
Disconnect the computer and check the connections of the connector (tracks 19, 20, 41 and 42).
Attach 64-track adapter (Elé. 1717).
The CLIP or XRBAG tool absolutely must be used to measure the resistance in adapter cable J.
If the value indicated is incorrect, the wiring between the computer and the driver's side rear seat belt retractor
ignition module (C0/C3) is faulty.
Repair or replace the wiring if necessary.
The CLIP or XRBAG absolutely must be used to measure the resistance in adapter cable E.
If the value indicated is incorrect, the wiring between the passenger's side rear seat belt retractor ignition
module (C0/C3) is faulty.
Repair or replace the wiring if necessary.
AFTER REPAIRReconnect the computer and seat belt retractor, then switch on the ignition again.
Clear the computer memory then switch off the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy any retractors that have been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0
Page 61 of 68
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Fault Interpretation
88C - 61
88C
V3 MR-372-J84-88C000$072.mif
AIRBAG ACU4
Vdiag: 04
DF239
CONTINUED
CC.0 - CC.1
NOTESNone.
Lock the computer.
Disconnect the computer and check the connections of the connector (tracks 19, 20, 41 and 42).
Attach 64-track adapter (Elé. 1717).
The CLIP or XRBAG absolutely must be used to measure the proper insulation for the type of fault in adapter
cable J.
If the value indicated is incorrect, the wiring between the computer and the driver's side rear seat belt retractor
ignition module (C0/C3) is faulty.
Repair or replace the wiring if necessary.
The CLIP or XRBAG tool absolutely must be used to measure the proper insulation for the type of fault in
adapter cable E.
If the value indicated is incorrect, the wiring between the computer and the passenger's side rear seat belt
retractor ignition module (C0/C3) is faulty.
Repair or replace the wiring if necessary.
AFTER REPAIRReconnect the computer and seat belt retractor, then switch on the ignition again.
Clear the computer memory then switch off the ignition.
Carry out the check again using the diagnostic tool and, if there are no faults, unlock
the computer.
Destroy any retractors that have been replaced (tool Elé. 1287).
ACU4 Vdiag04 J84 1.0