deactivate passenger airbag RENAULT SCENIC 2011 J95 / 3.G Air Bag RC5 - Seat Belt Pretensioners Workshop Manual

88C-11
MR-372-J84-88C100$118.mif
V5
88C
AIRBAGS AND PRETENSIONERS
Fault finding – System operation
The purpose of the air bag system RC5 P1/P2 is to provide optimum safety protection for all of the vehicle
occupants.
Special notes:
The MEGANE is equipped with driver and passenger seat belt buckle pretensioners in the front section.
The MEGANE is equipped with an "anti-submarine" airbag inside the seat base
The MEGANE is equipped with driver and passenger chest-level airbags in the rear section.

On MEGANE phase 1,
Warning light management: the status of the airbag fault warning light takes priority in relation to the status of
the passenger airbag warning light.
Impact management: a single level is emitted over the CAN line.
On MEGANE phase 2,
Warning light management: the two warning lights cannot be separated and the status of the passenger airbag
warning light is maintained when the airbag fault warning light illuminates.
Impact management: two levels of separate impacts are emitted over the CAN line.
Frontal impacts:
This function is performed entirely inside the computer. Accelerometers measure the violence of the impact. Vehicle
speed, driver's seat position, passenger airbag locking switching position and the accelerometer measurements
determine the strategy that the computer adopts to trigger the ignition modules. The front and rear seat belt inertia
reels, the front seat belt pretensioners, the face air bags (levels 1 and 2) can also be triggered or not according to
the entry parameters.
Side impacts:
This function is performed by the computer and the side impact sensors.
The position of the passenger airbag locking switch and the accelerometer measurements determine the strategy
that the computer adopts to trigger the ignition modules. The seat belt inertia reels, the seat belt pretensioners,
the front chest airbags and the curtain airbags thus may or may not be triggered.
Seat belt locking monitoring:
This function is performed by the instrument panel. The computer only sends the driver's seat belt buckle sensor
status. A warning light on the instrument panel is displayed if the driver is not wearing his seat belt, and a buzzer
reminds the driver of this when the vehicle speed exceeds 12 mph (20 km/h).
Inhibition of passenger trigger lines:
This function is performed by the computer and the passenger airbag locking switch.
The choice of whether or not to deactivate the passenger airbags must be made before the vehicle speed exceeds
0.3 mph (0.5 km/h). The computer measures an impedance (100Ω= Passenger Airbag deactivated;
400Ω= Passenger Airbag active). Above the threshold, any action on the locking switch results in storage of
the fault DF193and the instrument panel warning light is illuminated.
The front passenger airbag (levels 1 and 2), the passenger lap belt pretensioner and the front passenger
chest-level airbag are deactivated when the locking switch is in the OFF position or when the fault
DF193 "Change of passenger airbag locking status" is present in the computer memory.
Monitoring the information displayed on the instrument panel:
The instrument panel controls the correct working of warning lights "air bag failure" and "air bag OFF" and informs
the air bag computer about possible warning light circuit failures through the multiplex network.
AIRBAG RC5
Vdiag: 14

88C-72
MR-372-J84-88C100$472.mif
V5
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults
AIRBAG RC5
Vdiag: 14
88C
DF193
PRESENT
OR
STOREDPASSENGER AIRBAG LOCKING CHANGE OF STATUS
NOTESSpecial notes:
The vehicle user must deactivate or reactivate the passenger airbag using the switch
before the vehicle exceeds a speed of 0.3 mph (0.5 km/h). Above this speed,
the computer stores this fault and illuminates the instrument panel warning light.
Clear the computer fault memory.
Switch off the ignition, and wait a few seconds.
Set the locking switch to the desired setting.
Switch the ignition back on and check that the fault is no longer present.
AFTER REPAIRClear the computer fault memory. Switch off the ignition.
Carry out the check again using the diagnostic tool and, if there is no fault, unlock
the computer.
ABGRC5_V14_DF193