wheel RENAULT SCENIC 2011 J95 / 3.G Air Bag RC5 - Seat Belt Pretensioners Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2011, Model line: SCENIC, Model: RENAULT SCENIC 2011 J95 / 3.GPages: 88, PDF Size: 0.47 MB
Page 42 of 88
88C-42
MR-372-J84-88C100$413.mif
V5
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults
AIRBAG RC5
Vdiag: 14
88C
DF071
PRESENT
OR
STORED
DRIVER'S FRONT AIRBAG CIRCUIT 2
CC : Short circuit
CO : Open circuit
CC.1: Short circuit to +12 volts
CC.0 : Short circuit to earth
1.DEF : Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Special notes:
Never take measurements on the ignition lines with any tool other than the CLIP or
XRBAG tool.
Use the 22-track adapter Elé. 1685 when working on the computer connector and
use the 10-track adapter Elé. 1617 when working on the rotary switch.
CO
CC
NOTESNone.
Lock the computer using the diagnostic tool.
Switch off the ignition and remove the driver's frontal airbag.
Check that it is correctly connected.
Disconnect the driver's frontal airbag and attach 2 dummy ignition modules to the ignition module connectors.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the driver's frontal airbag if the fault becomes stored (fault no longer declared present).
With the ignition switched off, disconnect and reconnect the rotary switch connector under the steering wheel.
Check the connections if the fault has become stored (fault no longer declared present).
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on
the ignition again.
Clear the computer fault memory. Switch off the ignition.
Carry out the check again using the diagnostic tool and, if there is no fault, unlock the
computer. When replacing the airbag module, do not forget to reconnect the earth on
the new module.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).
ABGRC5_V14_DF071
Page 43 of 88
88C-43
MR-372-J84-88C100$413.mif
V5
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults
AIRBAG RC5
Vdiag: 14
88C
DF071
CONTINUED
Fit the 10-track Elé. 1617 to the rotary switch at the point C2 (tracks 9 and 10).
The CLIP or XRBAG tool must be used to measure the resistance on the adapter cable A.
If the value obtained is incorrect, replace the rotary switch under the steering wheel.
Reconnect the steering wheel rotary switch, disconnect the computer and check the connections of the 22-track
connector (tracks 4 and 15).
fit the 22-track test adapter Elé. 1685.
The CLIP or XRBAG tool must be used to measure the resistance in adapter cable D.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector (C0/
C2). Replace the wiring if necessary.
CC.1
CC.0
NOTESNone.
Lock the computer using the diagnostic tool.
Switch off the ignition and remove the driver's frontal airbag.
Check the condition and correct connection of the trigger lines.
Fit the 10-track test adapter to the rotary switch at the point C2 (tracks 9 and 10).
The CLIP or XRBAG tool must be used to measure the resistance appropriate to the type of fault on the adapter
cable A.
If the value obtained is incorrect, replace the rotary switch under the steering wheel.
Reconnect the rotary switch to the steering wheel, disconnect the computer and check the connector connections
(tracks 4 and 15).
fit the 22-track test adapter Elé. 1685.
The CLIP or XRBAG tool must be used to measure the insulation appropriate to the type of fault on the adapter
cable D.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector (C0/
C2). Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on
the ignition again.
Clear the computer fault memory. Switch off the ignition.
Carry out the check again using the diagnostic tool and, if there is no fault, unlock the
computer. When replacing the airbag module, do not forget to reconnect the earth on
the new module.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).
Page 44 of 88
88C-44
MR-372-J84-88C100$413.mif
V5
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults
AIRBAG RC5
Vdiag: 14
88C
DF072
PRESENT
OR
STORED
DRIVER'S FRONT AIRBAG CIRCUIT 1
CC : Short circuit
CO : Open circuit
CC.1: Short circuit to +12 volts
CC.0 : Short circuit to earth
1.DEF : Configuration
NOTESIf 1.DEF, check and modify the computer configuration.
Special notes:
Never take measurements on the ignition lines with any tool other than the CLIP or
XRBAG tool.
Use the 22-track adapter Elé. 1685 when working on the computer connector and
use the 10-track adapter Elé. 1617 when working on the rotary switch.
CO
CC
NOTESNone.
Lock the computer using the diagnostic tool.
Switch off the ignition and remove the driver's frontal airbag.
Check that it is correctly connected.
Disconnect the driver's frontal airbag and attach 2 dummy ignition modules to the ignition module connectors.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the driver's frontal airbag if the fault becomes stored (fault no longer declared present).
With the ignition switched off, disconnect and reconnect the rotary switch connector under the steering wheel.
Check the connections if the fault has become stored (fault no longer declared present).
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on
the ignition again.
Clear the computer fault memory. Switch off the ignition.
Carry out the check again using the diagnostic tool and, if there is no fault, unlock the
computer. When replacing the airbag module, do not forget to reconnect the earth on
the new module.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).
ABGRC5_V14_DF072
Page 45 of 88
88C-45
MR-372-J84-88C100$413.mif
V5
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults
AIRBAG RC5
Vdiag: 14
88C
DF072
CONTINUED
Fit the 10-track Elé. 1617 to the rotary switch at the point C2 (tracks 9 and 10).
The CLIP or XRBAG tool must be used to measure the resistance on the adapter cable A.
If the value obtained is incorrect, replace the rotary switch under the steering wheel.
Reconnect the rotary switch to the steering wheel, disconnect the computer and check the connector connections
(tracks 3 and 14).
fit the 22-track test adapter Elé. 1685.
The CLIP or XRBAG tool must be used to measure the resistance on the adapter cable C.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector (C0/C2).
Replace the wiring if necessary.
CC.1
CC.0NOTESNone.
Lock the computer using the diagnostic tool.
Switch off the ignition and remove the driver's frontal airbag.
Check the condition and correct connection of the trigger lines.
Fit the 10-track test adapter to the rotary switch at the point C2 (tracks 6 and 7).
The CLIP or XRBAG tool must be used to measure the resistance appropriate to the type of fault on the adapter
cable B.
If the value obtained is incorrect, replace the rotary switch under the steering wheel.
Reconnect the rotary switch to the steering wheel, disconnect the computer and check the connector connections
(tracks 3 and 14).
fit the 22-track test adapter Elé. 1685.
The CLIP or XRBAG tool must be used to measure the insulation appropriate to the type of fault on the adapter
cable C.
If the value obtained is incorrect, the wiring is faulty between the computer and the rotary switch connector (C0/C2).
Replace the wiring if necessary.
AFTER REPAIRReconnect the computer and driver's frontal airbag ignition modules, then switch on
the ignition again.
Clear the computer fault memory. Switch off the ignition.
Carry out the check again using the diagnostic tool and, if there is no fault, unlock the
computer. When replacing the airbag module, do not forget to reconnect the earth on
the new module.
Destroy the driver's front airbag if it has been replaced (tool Elé. 1287).