engine RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual

13B-196
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 1
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405: "Clutch pedal".
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical definition and, in particular, the automatic gearbox
computer configuration (see 88B, Multiplex).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button is
pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 4 without pressing the 0 button, refer to the
interpretation of status ET703 Cruise control/speed limiter buttons and test the R/0
control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-199
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 9
Vehicle speed monitoring
Status ET415 changes to STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 9 continues, contact the Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes "STATUS 10" when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) if the injection computer detects
a fault anywhere in the engine management system, or an engine speed that is too high
or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with present or stored faults.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 10 continues, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-200
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
EGR PROGRAMMING CUT-OFF
STATUS DEFINITIONThis status indicates the EGR valve programming cut-off.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
STATUS 1, 5, 6, 7, 9,
10, 12, 13, 15, 19
23, 24Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
STATUS 3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal (ET405 "Clutch pedal switch") is not pressed and that the
vehicle has stopped completely.
STATUS 4, 17Test the present and stored faults and repair.
STATUS 8Reset the EGR offsets by referring to the interpretation of command SC036
"Reinitialise programming" and select "EGR valve".
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET651/EDC16_V58_ET651/EDC16_V5C_ET651/EDC16_V18_ET651/EDC16_V1C_ET651/EDC16_V20_ET651

13B-201
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
CONTINUED
STATUS 11, 22
Allow the engine to heat up until this cut-off disappears.
STATUS 18Check that the regeneration of the particle filter in progress has completely finished.
STATUS 20Allow the engine to cool until this cut-off disappears.
STATUS 21Too low atmospheric pressure, the EGR valve is disabled.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-206
MR-372-J84-13B200$540.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715STORED ENGINE STATUS NO. 1
STORED ENGINE STATUS NO. 2
STORED ENGINE STATUS NO. 3
STORED ENGINE STATUS NO. 4
STORED ENGINE STATUS NO. 5
STORED ENGINE STATUS NO. 6
STORED ENGINE STATUS NO. 7
STORED ENGINE STATUS NO. 8
STORED ENGINE STATUS NO. 9
STORED ENGINE STATUS NO. 10
STATUS DEFINITIONThese statuses indicate the recorded engine status for failed regenerations when
driving.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
These statuses should only be interpreted if DF312 "Speed request" is present or
stored.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
This status shows the stored engine status during a regeneration failure when driving:
NONE, + AFTER IGNITION, RUNNING, STOPPED.
Each STATUS between ET706 and ET715 corresponds to regeneration failures for which the mileage is recorded
from PR794 Stored regeneration failure no. 1 to PR803 Stored regeneration failure no. 10 (for example,
PR797 Stored regeneration failure no. 4 is related to ET709 Stored engine status no. 4).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET706/EDC16_V58_ET706/EDC16_V5C_ET706/EDC16_V50_ET707/EDC16_V58_ET707/EDC16_V5C_ET707/
EDC16_V50_ET708/EDC16_V58_ET708/EDC16_V5C_ET708/EDC16_V50_ET709/EDC16_V58_ET709/EDC16_V5C_ET709/
EDC16_V50_ET710/EDC16_V58_ET710/EDC16_V5C_ET710/EDC16_V50_ET711/EDC16_V58_ET711/EDC16_V5C_ET711/
EDC16_V50_ET712/EDC16_V58_ET712/EDC16_V5C_ET712/EDC16_V50_ET713/EDC16_V58_ET713/EDC16_V5C_ET713/
EDC16_V50_ET714/EDC16_V58_ET714/EDC16_V5C_ET714/EDC16_V50_ET715/EDC16_V58_ET715/EDC16_V5C_ET715/
EDC16_V18_ET706/EDC16_V1C_ET706/EDC16_V20_ET706/EDC16_V18_ET707/EDC16_V1C_ET707/EDC16_V20_ET707/
EDC16_V18_ET708/EDC16_V1C_ET708/EDC16_V20_ET708/EDC16_V18_ET709/EDC16_V1C_ET709/EDC16_V20_ET709/
EDC16_V18_ET710/EDC16_V1C_ET710/EDC16_V20_ET710/EDC16_V18_ET711/EDC16_V1C_ET711/EDC16_V20_ET711/
EDC16_V18_ET712/EDC16_V1C_ET712/EDC16_V20_ET712/EDC16_V18_ET713/EDC16_V1C_ET713/EDC16_V20_ET713/
EDC16_V18_ET714/EDC16_V1C_ET714/EDC16_V20_ET714/EDC16_V18_ET715/EDC16_V1C_ET715/EDC16_V20_ET715

13B-207
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715
CONTINUED
RUNNING
If the STATUS is "RUNNING", regeneration failed because:
– the customer's driving did not generate enough heat,
– an engine management system component is faulty.
STOPPEDIf the STATUS is "STOPPED", regeneration failed because the engine was switched off.
NONENo failed regeneration is present.
+ APCPOWER LATCH
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-208
MR-372-J84-13B200$540.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751STORED REGEN.* REQUEST STATUS NO. 1
STORED REGEN.* REQUEST STATUS NO. 2
STORED REGEN.* REQUEST STATUS NO. 3
STORED REGEN.* REQUEST STATUS NO. 4
STORED REGEN.* REQUEST STATUS NO. 5
STORED REGEN.* REQUEST STATUS NO. 6
STORED REGEN.* REQUEST STATUS NO. 7
STORED REGEN.* REQUEST STATUS NO. 8
STORED REGEN.* REQUEST STATUS NO. 9
STORED REGEN.* REQUEST STATUS NO. 10
STATUS DEFINITIONStatuses ET742 to ET751 correspond to the causes of the regeneration request. They
are associated with parameters PR816 "Stored regeneration start No. 1" to PR825
"Stored regeneration start No. 10" which contain the record of the vehicle mileage at
the start of regeneration (eg. PR745 "Stored regeneration start No. 4" is associated
with "ET709 Stored regeneration request status no. 4").
NOTESSpecial note:
These statuses should only be interpreted for ALP9: Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET742/EDC16_V58_ET742/EDC16_V5C_ET742/EDC16_V50_ET743/EDC16_V58_ET743/EDC16_V5C_ET743/
EDC16_V50_ET743/EDC16_V58_ET744/EDC16_V5C_ET744/EDC16_V50_ET745/EDC16_V58_ET745/EDC16_V5C_ET745/
EDC16_V50_ET745/EDC16_V58_ET746/EDC16_V5C_ET746/EDC16_V50_ET747/EDC16_V58_ET747/EDC16_V5C_ET747/
EDC16_V50_ET747/EDC16_V58_ET748/EDC16_V5C_ET748/EDC16_V50_ET749/EDC16_V58_ET749/EDC16_V5C_ET749/
EDC16_V50_ET750/EDC16_V58_ET750/EDC16_V5C_ET750/EDC16_V50_ET751/EDC16_V58_ET751/EDC16_V5C_ET751/
EDC16_V18_ET742/EDC16_V1C_ET742/EDC16_V20_ET742/EDC16_V18_ET743/EDC16_V1C_ET743/EDC16_V20_ET743/
EDC16_V18_ET743/EDC16_V1C_ET744/EDC16_V20_ET744/EDC16_V18_ET745/EDC16_V1C_ET745/EDC16_V20_ET745/
EDC16_V18_ET745/EDC16_V1C_ET746/EDC16_V20_ET746/EDC16_V18_ET747/EDC16_V1C_ET747/EDC16_V20_ET747/
EDC16_V18_ET747/EDC16_V1C_ET748/EDC16_V20_ET748/EDC16_V18_ET749/EDC16_V1C_ET749/EDC16_V20_ET749/
EDC16_V18_ET750/EDC16_V1C_ET750/EDC16_V20_ET750/EDC16_V18_ET751/EDC16_V1C_ET751/EDC16_V20_ET751

13B-210
MR-372-J84-13B200$576.mif
V13
13B
DIESEL INJECTION
Fault finding – Parameter summary table
* OCR: Opening cyclic ratioTool parameter Diagnostic tool title
PR002Alternator charge
PR005EGR valve opening setpoint
PR006Rail pressure regulator current
PR007Rail pressure regulator current setpoint
PR008Rail reference pressure
PR009Turbocharging pressure setpoint
PR011Turbocharging solenoid valve position sensor
PR015Engine torque
PR016Alternator flow (Vdiag 50, 58, 5C only)
PR017Fuel flow
PR022EGR valve position feedback loop difference
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure
PR038Rail pressure
PR041Turbocharging pressure
PR043Heating element power authorised
PR045Power requested by thermoplungers
PR047Turbocharging pressure *OCR
PR048Refrigerant pressure regulation valve *OCR
PR051EGR valve position feedback
PR053Engine speed requested by air conditioning
PR055Engine speed
PR058Inlet air temperature (Vdiag 18, 1C and 20 only)
PR059Inlet air temperature (Vdiag 50, 58 and 5C only)
MR-372-J84-13B200$576.mif
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C

13B-214
MR-372-J84-13B200$612.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of parameters
PR002
ALTERNATOR CHARGE
PARAMETER
DEFINITIONThis parameter indicates the alternator charge value in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80°C.
The alternator charge value varies according to the battery voltage.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR002/EDC16_V58_PR002/EDC16_V5C_PR002/EDC16_V18_PR002/EDC16_V1C_PR002/EDC16_V20_PR002 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$612.mif

13B-215
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR005
EGR VALVE OPENING VALUE REQUIRED
PARAMETER
DEFINITIONThis parameter indicates a theoretical opening value for the EGR valve giving optimum
engine performance.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
The EGR valve theoretical opening value for operation with the engine stopped and ignition on is:
- 10 < PR005 < 0%.
In the event of a fault, refer to the interpretation of fault DF272 EGR control circuit.
Conformity check with the engine running and engine coolant temperature > 80°C.
The theoretical EGR valve opening value for operation with the engine running and the engine coolant
temperature > 80°C is 10 < PR005 < 40%.
If there is a fault, refer to the interpretation of fault DF272 EGR control circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR005/EDC16_V58_PR005/EDC16_V5C_PR005/EDC16_V18_PR005/EDC16_V1C_PR005/EDC16_V20_PR005