RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual
Manufacturer: RENAULT, Model Year: 2011, Model line: SCENIC, Model: RENAULT SCENIC 2011 J95 / 3.GPages: 365, PDF Size: 2.11 MB
Page 281 of 365
13B-281
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR667
TURBINE UPSTREAM TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the turbine upstream temperature in °C.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C.
Indicates the turbine upstream air temperature in °C,which is ≈ 200°C.
In the event of a fault, refer to the interpretation of DF652 Turbine upstream temperature sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR667/EDC16_V58_PR667/EDC16_V5C_PR667/EDC16_V18_PR667/EDC16_V1C_PR667/EDC16_V20_PR667
Page 282 of 365
13B-282
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR668
TURBINE UPSTREAM TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the turbine upstream temperature sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
The voltage must be between 4.95 V < PR668 < 5 V.
In the event of a fault, refer to the interpretation of DF652 Turbine upstream temperature sensor circuit.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR668/EDC16_V58_PR668/EDC16_V5C_PR668/EDC16_V18_PR668/EDC16_V1C_PR668/EDC16_V20_PR668
Page 283 of 365
13B-283
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR672
DAMPER VALVE POSITION SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the damper valve position setpoint as a %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
PR672 < 5%
In the event of a fault, refer to the interpretation for DF226 Damper valve circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR672/EDC16_V58_PR672/EDC16_V5C_PR672/EDC16_V18_PR672/EDC16_V1C_PR672/EDC16_V20_PR672
Page 284 of 365
13B-284
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793DF312 RECORD NO. 1
DF312 RECORD NO. 2
DF312 RECORD NO. 3
DF312 RECORD NO. 4
DF312 RECORD NO. 5
DF312 RECORD NO. 6
DF312 RECORD NO. 7
DF312 RECORD NO. 8
DF312 RECORD NO. 9
DF312 RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
These parameters must only be interpreted for DF312 Speed request if it is present
or stored.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
In the event of a fault, consult the interpretation of fault DF312 Speed request.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR784/EDC16_V58_PR784/EDC16_V5C_PR784/EDC16_V50_PR785/EDC16_V58_PR785/EDC16_V5C_PR785/
EDC16_V50_PR786/EDC16_V58_PR786/EDC16_V5C_PR786/EDC16_V50_PR787/EDC16_V58_PR787/EDC16_V5C_PR787/
EDC16_V50_PR788/EDC16_V58_PR788/EDC16_V5C_PR788/EDC16_V50_PR789/EDC16_V58_PR789/EDC16_V5C_PR789/
EDC16_V50_PR790/EDC16_V58_PR790/EDC16_V5C_PR790/EDC16_V50_PR791/EDC16_V58_PR791/EDC16_V5C_PR791/
EDC16_V50_PR792/EDC16_V58_PR792/EDC16_V5C_PR792/EDC16_V50_PR793/EDC16_V58_PR793/EDC16_V5C_PR793/
EDC16_V18_PR784/EDC16_V1C_PR784/EDC16_V20_PR784/EDC16_V18_PR785/EDC16_V1C_PR785/EDC16_V20_PR785/
EDC16_V18_PR786/EDC16_V1C_PR786/EDC16_V20_PR786/EDC16_V18_PR787/EDC16_V1C_PR787/EDC16_V20_PR787/
EDC16_V18_PR788/EDC16_V1C_PR788/EDC16_V20_PR788/EDC16_V18_PR789/EDC16_V1C_PR789/EDC16_V20_PR789/
EDC16_V18_PR790/EDC16_V1C_PR790/EDC16_V20_PR790/EDC16_V18_PR791/EDC16_V1C_PR791/EDC16_V20_PR791/
EDC16_V18_PR792/EDC16_V1C_PR792/EDC16_V20_PR792/EDC16_V18_PR793/EDC16_V1C_PR793/EDC16_V20_PR793/
Page 285 of 365
13B-285
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793
CONTINUED
These parameters are used so that the history of the last ten regeneration failures when driving are known.
For VDIAG 58, 18, 1C:
Each parameter from PR784 to PR793 records the mileage when the particle filter warning light comes on which
is associated with DF312 Speed request.
Each time the particle filter warning light comes on, the vehicle mileage is stored in the following parameter
(PR+1).
When all ten parameters have a value other than zero and the particle filter warning light is illuminated again, the
mileage information for PR784 is cleared and replaced by the new value.
For VDIAG 5C and 20
Each parameter from PR784 to PR793 contains a record of the vehicle mileage when the particle filter warning
light illuminates. The appearance of fault DF312 Speed request is associated with each of these parameters.
PR784 to PR793 operate through successive feedback (when the particle filter warning light comes on, the value
of PR784 is copied to PR785, the value of PR785 is copied to PR786 and so on).
When there are more than ten records, the value of PR793 is overwritten. The new mileage is allocated to PR784.
If none of the parameters between PR784 and PR793 is available in the sub-function, this means than nothing
has been recorded. The parameters appear in the sub-function when they have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 286 of 365
13B-286
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803REGENERATION FAILURE RECORD NO. 1
REGENERATION FAILURE RECORD NO. 2
REGENERATION FAILURE RECORD NO. 3
REGENERATION FAILURE RECORD NO. 4
REGENERATION FAILURE RECORD NO. 5
REGENERATION FAILURE RECORD NO. 6
REGENERATION FAILURE RECORD NO. 7
REGENERATION FAILURE RECORD NO. 8
REGENERATION FAILURE RECORD NO. 9
REGENERATION FAILURE RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only if DF312 Speed request is present or stored.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten regeneration failures when driving are known.
For VDIAG 58, 18, 1C
Each of these parameters contains the vehicle mileage during a failed particle filter regeneration when driving.
Each parameter relates to an engine status. The statuses and parameters are recorded at the same time
(for example PR797 is associated with ET709 Engine status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero and there is a regeneration failure when driving, the
mileage information for PR794 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR794/EDC16_V58_PR794/EDC16_V5C_PR794/EDC16_V50_PR795/EDC16_V58_PR795/EDC16_V5C_PR795/
EDC16_V50_PR796/EDC16_V58_PR796/EDC16_V5C_PR796/EDC16_V50_PR797/EDC16_V58_PR797/EDC16_V5C_PR797/
EDC16_V50_PR798/EDC16_V58_PR798/EDC16_V5C_PR798/EDC16_V50_PR799/EDC16_V58_PR799/EDC16_V5C_PR799/
EDC16_V50_PR800/EDC16_V58_PR800/EDC16_V5C_PR800/EDC16_V50_PR801/EDC16_V58_PR801/EDC16_V5C_PR801/
EDC16_V50_PR802/EDC16_V58_PR802/EDC16_V5C_PR802/EDC16_V50_PR803/EDC16_V58_PR803/EDC16_V5C_PR803/
EDC16_V18_PR794/EDC16_V1C_PR794/EDC16_V20_PR794/EDC16_V18_PR795/EDC16_V1C_PR795/EDC16_V20_PR795/
EDC16_V18_PR796/EDC16_V1C_PR796/EDC16_V20_PR796/EDC16_V18_PR797/EDC16_V1C_PR797/EDC16_V20_PR797/
EDC16_V18_PR798/EDC16_V1C_PR798/EDC16_V20_PR798/EDC16_V18_PR799/EDC16_V1C_PR799/EDC16_V20_PR799/
EDC16_V18_PR800/EDC16_V1C_PR800/EDC16_V20_PR800/EDC16_V18_PR801/EDC16_V1C_PR801/EDC16_V20_PR801/
EDC16_V18_PR802/EDC16_V1C_PR802/EDC16_V20_PR802/EDC16_V18_PR803/EDC16_V1C_PR803/EDC16_V20_PR803
Page 287 of 365
13B-287
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803
CONTINUED
For VDIAG 5C and 20
Each parameter between PR794 and PR803 contains the vehicle mileage when particle filter regeneration fails
when driving. Each parameter relates to an engine status. They are recorded simultaneously (for example, PR797
is associated with ET709 Engine status record no. 4).
PR795 to PR803 operate through successive feedback (when regeneration fails whilst driving, the value of
PR794 is copied in PR795, the value of PR795 is copied in PR796 and so on).
When there are more than ten records, the value of PR803 is overwritten. The new mileage is allocated to PR794.
If none of parameters PR794 to PR803 is available in the sub-function, this means that no record has been made.
The parameters appear in the sub-function when they have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 288 of 365
13B-288
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
* rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
REGENERATION START RECORD NO. 1
REGENERATION START RECORD NO. 2
REGENERATION START RECORD NO. 3
REGENERATION START RECORD NO. 4
REGENERATION START RECORD NO. 5
REGENERATION START RECORD NO. 6
REGENERATION START RECORD NO. 7
REGENERATION START RECORD NO. 8
REGENERATION START RECORD NO. 9
REGENERATION START RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only for ALP9 Particle filter warning light comes on too
often.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten activations of the particle filter warning light are
known.
For VDIAG 58, 18 and 1C
Each parameter between PR816 and PR825 contains the vehicle mileage when particle filter regeneration starts
when driving. Each parameter is connected with a "Rege* request status record". They are recorded
simultaneously (for example, PR819 is associated with ET745 Rege* request status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero, and a new regeneration starts when driving, the mileage
information for PR816 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR816/EDC16_V58_PR816/EDC16_V5C_PR816/EDC16_V50_PR817/EDC16_V58_PR817/EDC16_V5C_PR817/
EDC16_V50_PR818/EDC16_V58_PR818/EDC16_V5C_PR818/EDC16_V50_PR819/EDC16_V58_PR819/EDC16_V5C_PR819/
EDC16_V50_PR820/EDC16_V58_PR820/EDC16_V5C_PR820/EDC16_V50_PR821/EDC16_V58_PR821/EDC16_V5C_PR821/
EDC16_V50_PR822/EDC16_V58_PR822/EDC16_V5C_PR822/EDC16_V50_PR823/EDC16_V58_PR823/EDC16_V5C_PR823/
EDC16_V50_PR824/EDC16_V58_PR824/EDC16_V5C_PR824/EDC16_V50_PR825/EDC16_V58_PR825/EDC16_V5C_PR825/
EDC16_V18_PR816/EDC16_V1C_PR816/EDC16_V20_PR816/EDC16_V18_PR816/EDC16_V1C_PR817/EDC16_V20_PR817/
EDC16_V18_PR816/EDC16_V1C_PR818/EDC16_V20_PR818/EDC16_V18_PR819/EDC16_V1C_PR819/EDC16_V20_PR819/
EDC16_V18_PR820/EDC16_V1C_PR820/EDC16_V20_PR820/EDC16_V18_PR821/EDC16_V1C_PR821/EDC16_V20_PR821/
EDC16_V18_PR822/EDC16_V1C_PR822/EDC16_V20_PR822/EDC16_V18_PR823/EDC16_V1C_PR823/EDC16_V20_PR823/
EDC16_V18_PR824/EDC16_V1C_PR824/EDC16_V20_PR824/EDC16_V18_PR825/EDC16_V1C_PR825/EDC16_V20_PR825
Page 289 of 365
13B-289
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
CONTINUED
For VDIAG 5C and 20
Each parameter from PR816 to PR825 records the mileage when particle filter regeneration starts and the status
of each request is recorded by ET742 Rege* request status record no. 1 to ET751 Rege* request status
record no. 10 (for example, PR819 is associated with ET745 Rege* request status record no.4).
Each time a new regeneration when driving is started, the vehicle mileage is recorded in PR816, as well as its
status in ET742 Rege* request status record no. 1
PR816 to PR825 operate through successive feedback (when regeneration starts, the value of PR816 is copied to
PR817, the value of PR817 is copied to PR818 and so on).
When there are more than ten records, the value of PR825 is overwritten.
The new mileage is allocated to PR816.
If only parameter PR816 is available in the sub-function and it has a value of zero, this means that no record was
made.
If a recording has been made, it will have a value above zero.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 290 of 365
13B-290
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR1012
WEIGHT OF SOOT AFTER REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in g present in the particle filter after
a regeneration.
NOTESThis parameter is to be consulted after using SC017 Particle filter regeneration.
Conformity check with the engine stopped and ignition on, or the engine running and engine coolant
temperature > 80°C, without electrical consumers
If PR1012 is less than 15 g, the particle filter regeneration completed correctly.
If PR1012 is greater than 15 g, a second particle filter regeneration must be performed using command SC017
Particle filter regeneration.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool
down for 2 hours with the bonnet open.
Do not perform a routine oil change before a second After-Sales regeneration (see SC017 Particle filter
regeneration).
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR1012/EDC16_V58_PR1012/EDC16_V5C_PR1012/EDC16_V18_PR1012/EDC16_V1C_PR1012/EDC16_V20_PR1012