cruise control RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Owner's Manual

13B-181
MR-372-J84-13B200$504.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 6
CRUISE CONTROL
Procedure to apply for Mégane II and Scénic II:
When the driver presses the main switch in the cruise control position, status ET042
becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears even though the cruise control button is
pressed, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V after ignition on the main switch connector.
●Connection code AP43 of component 1081 (Mégane II).
●Connection code AP43 of component 1546 (Scénic II).
Disconnect the switch and when it is in the rest position, check the insulation between:
●Connection code AP43 and 3FX of component 1081 (Mégane II).
●Connection code AP43 and 3PD of component 1081 (Mégane II).
●Connection code AP43 and 3FX of component 1546 (Scénic II).
●Connection code AP43 and 3PD of component 1546 (Scénic II).
– Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) and component 1546 (Scénic II) in the speed limiter position.
– Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) and component 1546 (Scénic II) in the cruise control position.
If these checks show incorrect values, replace the main switch.
Check the insulation, continuity, and the absence of interference resistance on the
following connections:
●Connection code 3FX,
●Connection code3PD.
Between components 1081 and 120 (Mégane II).
Between components 1546 and 120 (Scénic II).
Also check the engine management computer connectors.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-195
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CRUISE CONTROL/SPEED LIMITER DEACTIVATION
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system operation
programming.
Note:
Cruise control can be activated when the vehicle speed exceeds 20 mph (30 km/h).
Status ET415 shows various factors that cause deactivation of the cruise control/speed limiter function, due to a
driver request or the external environment (eg. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ007 Fault memory, to reset this status to WITHOUT.
NONE
This status is present on the diagnostic tool if:
the computer has been reinitialised,
the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving, with cruise control active (ET042:
Cruise control/Speed limiter: CRUISE CONTROL) and upon a traction control
request.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 1 without a traction control request (see38C, ABS).
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes "STATUS 2" when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No 1 and No 2.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET415/EDC16_V58_ET415/EDC16_V5C_ET415/EDC16_V18_ET415/EDC16_V1C_ET415/EDC16_V20_ET415

13B-196
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 1
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405: "Clutch pedal".
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical definition and, in particular, the automatic gearbox
computer configuration (see 88B, Multiplex).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button is
pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 4 without pressing the 0 button, refer to the
interpretation of status ET703 Cruise control/speed limiter buttons and test the R/0
control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-197
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has been
pressed.
If status ET415 is STATUS 5, refer to the interpretation of:
– of status ET042 Cruise control/speed limiter,
– of status ET703 Cruise control/speed limiter buttons,
– of status ET704 Brake contact no. 1,
– and status ET705 Brake contact No 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults on the
diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 changes to "STATUS 5", deal with present faults or those stored in the
injection computer.
If the fault is still present, contact Techline.
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic
gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) and:
– If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, test
the ABS computer and check the configuration of the tyre size stored in the computer. If
the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-198
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 7
Inconsistency between the request and the vehicle speed
Status ET415 changes to STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/ speed
limiter: CRUISE CONTROL) and when there is a significant difference.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status ET415 changes to STATUS 7 where there is no significant difference in the
levels, contact the Techline.
STATUS 8Automatic transmission in defect mode.
Status ET415 becomes STATUS 8 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the automatic transmission is
in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic transmission
computer.
Deal with any present or stored faults (see 23A, Automatic transmission,
interpretation of faults).
Clear the automatic transmission computer fault memory by running command RZ007
"Fault memory".
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If STATUS 8 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-199
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 9
Vehicle speed monitoring
Status ET415 changes to STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 9 continues, contact the Techline.
STATUS 10Monitoring by injection computer
Status ET415 becomes "STATUS 10" when driving with cruise control active (ET042
"Cruise control/speed limiter": CRUISE CONTROL) if the injection computer detects
a fault anywhere in the engine management system, or an engine speed that is too high
or too low.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with present or stored faults.
Reinitialise status ET415 on the injection computer by running command RZ007
"Fault memory".
If status 10 continues, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-202
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Carry out these checks if the statuses do not correspond with system operation
programming.
INACTIVE
Status ET703 becomes INACTIVE when none of the cruise control/speed limiter
buttons are pressed. These buttons are located on the steering wheel.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 372 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
If status ET703 does not display INACTIVE,
– check the condition of the cruise control/speed limiter +/- button and the condition of
its connector.
– check the condition of the cruise control/speed limiter R/0 button and the condition of
its connector.
Repair if necessary.
INCREASEStatus ET703 becomes PLUS when the cruise control/speed limiter + button is pressed.
This button is on the steering wheel, on the left-hand side.
If status ET703 does not display PLUS, check the condition of the cruise control/speed
limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 372 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connections while pressing the "+" button
(on the button tracks):
– Connection code86G, of component 331.
– Connection code 86M of component 331.
If the resistance is not approximately 300 Ω, check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the +/- control button.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET703/EDC16_V58_ET703/EDC16_V5C_ET703/EDC16_V18_ET703/EDC16_V1C_ET703/EDC16_V20_ET703

13B-203
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 1
DECREASE
Status ET703 becomes "MINUS" when the cruise control/speed limiter "-" button is
pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not change to MINUS, check the condition of the cruise control/
speed limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the "-" button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 100 Ω, check the continuity of the connection
when the button is in rest position.
If there is continuity, replace the +/- control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to SUSPEND, check the condition of the cruise
control/speed limiter R/0 button, and the condition of its connector.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the 0 button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 0Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-204
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 2
RESUME
Status ET703 becomes RESUME when the cruise control/speed limiter R button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to RESUME, check the condition of the cruise control/
speed limiter R/0 button, and the condition of its connector. Repair if necessary.
To carry out the checks and measurements in complete safety, follow the instructions
for removing the driver's front airbag (see MR 364 (Mégane II), 370 (Scénic II) or 395
(Laguna II), Mechanical, 88C, Airbag and pretensioners, Driver's front airbag,
removal-refitting).
Measure the resistance of the following connection whilst pressing the R button
(on the button tracks):
●Connection code86G, of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is in rest position.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-211
MR-372-J84-13B200$576.mif
V13
DIESEL INJECTION
Fault finding – Parameter summary table
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
Tool parameter Diagnostic tool title
PR061Exterior air temperature
PR064Coolant temperature
PR066Oil temperature
PR071Computer feed voltage
PR073Air flowmeter feed voltage
PR076Refrigerant sensor voltage
PR077EGR valve position sensor voltage
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR083Air temperature sensor voltage
PR084Coolant temperature sensor voltage
PR085Oil temperature sensor voltage
PR089Vehicle speed
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR131EGR air flow variation
PR132Air flow
PR146Inlet air flow
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR157Fuel flow setpoint
PR171Air flow setpoint for EGR
PR190Idle speed setpoint
PR209Turbocharging pressure loop difference
PR213Rail pressure loop difference