warning light RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Repair Manual

13B-152
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF652
PRESENT
OR
STORED
TURBINE UPSTREAM TEMPERATURE SENSOR CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CC.1 : Short circuit to + 12 V
CO.1: Open circuit or short circuit to + 12 V
1.DEF: Signal outside upper limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present if:
– ignition is on (CC.0),
– following a road test, engine warm (CO.1).
Special notes:
If the fault is present:
– the EGR function is inhibited,
– particle filter regeneration is inhibited,
– the vehicle performance is reduced,
– the level 1 warning light is illuminated.
Priorities when dealing with a number of faults:
DF011 Sensor voltage supply no. 1
IMPORTANT
The turbine upstream temperature sensor only measures temperatures above
200°C.
Check the condition of the turbine upstream temperature sensor connector (see Wiring Diagram Technical
Note, Mégane II, Scénic II or Laguna II, component code 1589).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II, Scénic II or Laguna II, component code 120).
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, wiring: precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, absence of interference resistance and insulation against + 5 V and + 12 V of the
following connections:
– connection code 3ABS,
– connection code 3ABT.
Between components 120 and 1589.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity, absence of interference resistance and insulation to earth of connection 3ABS
between components 120 and 1589.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for earth on connection 3ABT of the turbine upstream temperature sensor
If the fault is still present, warm up the engine until PR064 Coolant temperature = 80°C.
Run the engine at fast idle speed:
PR055 Engine speed = 1500 rpm for 2 minutes.
If PR667 Turbine upstream temperature remains fixed at 200°C, replace the turbine upstream temperature
sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF652/EDC16_V58_DF652/EDC16_V5C_DF652/EDC16_V18_DF652/EDC16_V1C_DF652/EDC16_V20_DF652

13B-153
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF717
PRESENT
OR
STOREDPARTICLE FILTER UPSTREAM PRESSURE
1.DEF: Signal incoherent
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– the level 1 warning light is lit,
– the OBD warning light illuminates after three consecutive driving cycles (starting
+ 5 seconds + switch off the ignition and wait 1 minute),
– the particle filter fault finding procedure is inhibited,
– particle filter regeneration is inhibited.
Check the condition of the pressure pipe between the particle filter upstream take-off point and the differential
pressure sensor.
Check that the pipe is not crushed, blocked or pierced.
Check that it is correctly positioned and connected to the differential pressure sensor (see MR 395 (Laguna II),
370 (Scénic II) or 364 (Mégane II), Mechanical, 19B Exhaust, Particle filter pressure sensor: Removal –
Refitting).
Replace the pressure pipe if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF717/EDC16_V58_DF717/EDC16_V5C_DF717/EDC16_V18_DF717/EDC16_V1C_DF717/EDC16_V20_DF717

13B-154
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF778
PRESENT
OR
STOREDTURBINE UPSTREAM TEMPERATURE REGULATION
1.DEF: Measured temperature too high
2.DEF: Parameter at maximum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present if:
– the engine is started with a speed greater than 1750 rpm and a fuel flow greater
than 30 mg/st,,
– a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– the vehicle performance is reduced,
–the level 1 warning light is lit.
IMPORTANT
This fault can result in a rapid and significant fouling of the particle filter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF778/EDC16_V58_DF778/EDC16_V5C_DF778/EDC16_V18_DF778/EDC16_V1C_DF778/EDC16_V20_DF778

13B-158
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
*diff: differentialDF953
PRESENT
OR
STORED
PARTICLE FILTER ABSENT
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– blue/white smoke and black particles coming from the exhaust,
– the OBD warning light illuminates after three consecutive driving cycles (starting
+ 5 seconds + switch off the ignition and wait 1 minute).
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
–DF315 Particle filter diff* pressure sensor if it is present or stored.
–DF717 Particle filter upstream pressure if it is present or stored.
Use bornier Elé.1681 for all operations on the engine management computer
connector.
IMPORTANT
In the long term, this fault may lead to premature wear and a greater risk of
turbocharger failure.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note,
Mégane II, Scénic II or Laguna II, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II, Scénic II or Laguna II, component code 120).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, wiring: Precautions for repair), repair the connector(s); otherwise, replace the wiring.
Check the particle filter is present.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V50_DF953/EDC16_V58_DF953/EDC16_V5C_DF953/EDC16_V18_DF953/EDC16_V1C_DF953/EDC16_V20_DF953

13B-208
MR-372-J84-13B200$540.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751STORED REGEN.* REQUEST STATUS NO. 1
STORED REGEN.* REQUEST STATUS NO. 2
STORED REGEN.* REQUEST STATUS NO. 3
STORED REGEN.* REQUEST STATUS NO. 4
STORED REGEN.* REQUEST STATUS NO. 5
STORED REGEN.* REQUEST STATUS NO. 6
STORED REGEN.* REQUEST STATUS NO. 7
STORED REGEN.* REQUEST STATUS NO. 8
STORED REGEN.* REQUEST STATUS NO. 9
STORED REGEN.* REQUEST STATUS NO. 10
STATUS DEFINITIONStatuses ET742 to ET751 correspond to the causes of the regeneration request. They
are associated with parameters PR816 "Stored regeneration start No. 1" to PR825
"Stored regeneration start No. 10" which contain the record of the vehicle mileage at
the start of regeneration (eg. PR745 "Stored regeneration start No. 4" is associated
with "ET709 Stored regeneration request status no. 4").
NOTESSpecial note:
These statuses should only be interpreted for ALP9: Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET742/EDC16_V58_ET742/EDC16_V5C_ET742/EDC16_V50_ET743/EDC16_V58_ET743/EDC16_V5C_ET743/
EDC16_V50_ET743/EDC16_V58_ET744/EDC16_V5C_ET744/EDC16_V50_ET745/EDC16_V58_ET745/EDC16_V5C_ET745/
EDC16_V50_ET745/EDC16_V58_ET746/EDC16_V5C_ET746/EDC16_V50_ET747/EDC16_V58_ET747/EDC16_V5C_ET747/
EDC16_V50_ET747/EDC16_V58_ET748/EDC16_V5C_ET748/EDC16_V50_ET749/EDC16_V58_ET749/EDC16_V5C_ET749/
EDC16_V50_ET750/EDC16_V58_ET750/EDC16_V5C_ET750/EDC16_V50_ET751/EDC16_V58_ET751/EDC16_V5C_ET751/
EDC16_V18_ET742/EDC16_V1C_ET742/EDC16_V20_ET742/EDC16_V18_ET743/EDC16_V1C_ET743/EDC16_V20_ET743/
EDC16_V18_ET743/EDC16_V1C_ET744/EDC16_V20_ET744/EDC16_V18_ET745/EDC16_V1C_ET745/EDC16_V20_ET745/
EDC16_V18_ET745/EDC16_V1C_ET746/EDC16_V20_ET746/EDC16_V18_ET747/EDC16_V1C_ET747/EDC16_V20_ET747/
EDC16_V18_ET747/EDC16_V1C_ET748/EDC16_V20_ET748/EDC16_V18_ET749/EDC16_V1C_ET749/EDC16_V20_ET749/
EDC16_V18_ET750/EDC16_V1C_ET750/EDC16_V20_ET750/EDC16_V18_ET751/EDC16_V1C_ET751/EDC16_V20_ET751

13B-209
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751
CONTINUED
STATUS1
Request by weight of soot
Regeneration has been requested following measurement of the maximum weight of
soot in the particle filter, without the particle filter warning light coming on.
STATUS2Request by estimated weight of soot
Regeneration has been requested following an estimate of the maximum weight of soot
in the particle filter, without the particle filter warning light coming on.
STATUS3Request by distance travelled
Regeneration has been requested as the distance travelled since the last successful
regeneration has reached the maximum authorised value (the particle filter warning
light has not come on).
STATUS4Request by number of failed regenerations or soot weight
This status corresponds to the appearance of DF312 "Speed request".
This corresponds to the maximum number of failed regenerations or to the maximum
weight of soot in the particle filter, with the particle filter warning light coming on.
* REGEN: Regeneration
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-285
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793
CONTINUED
These parameters are used so that the history of the last ten regeneration failures when driving are known.
For VDIAG 58, 18, 1C:
Each parameter from PR784 to PR793 records the mileage when the particle filter warning light comes on which
is associated with DF312 Speed request.
Each time the particle filter warning light comes on, the vehicle mileage is stored in the following parameter
(PR+1).
When all ten parameters have a value other than zero and the particle filter warning light is illuminated again, the
mileage information for PR784 is cleared and replaced by the new value.
For VDIAG 5C and 20
Each parameter from PR784 to PR793 contains a record of the vehicle mileage when the particle filter warning
light illuminates. The appearance of fault DF312 Speed request is associated with each of these parameters.
PR784 to PR793 operate through successive feedback (when the particle filter warning light comes on, the value
of PR784 is copied to PR785, the value of PR785 is copied to PR786 and so on).
When there are more than ten records, the value of PR793 is overwritten. The new mileage is allocated to PR784.
If none of the parameters between PR784 and PR793 is available in the sub-function, this means than nothing
has been recorded. The parameters appear in the sub-function when they have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-288
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
* rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
REGENERATION START RECORD NO. 1
REGENERATION START RECORD NO. 2
REGENERATION START RECORD NO. 3
REGENERATION START RECORD NO. 4
REGENERATION START RECORD NO. 5
REGENERATION START RECORD NO. 6
REGENERATION START RECORD NO. 7
REGENERATION START RECORD NO. 8
REGENERATION START RECORD NO. 9
REGENERATION START RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only for ALP9 Particle filter warning light comes on too
often.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten activations of the particle filter warning light are
known.
For VDIAG 58, 18 and 1C
Each parameter between PR816 and PR825 contains the vehicle mileage when particle filter regeneration starts
when driving. Each parameter is connected with a "Rege* request status record". They are recorded
simultaneously (for example, PR819 is associated with ET745 Rege* request status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero, and a new regeneration starts when driving, the mileage
information for PR816 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR816/EDC16_V58_PR816/EDC16_V5C_PR816/EDC16_V50_PR817/EDC16_V58_PR817/EDC16_V5C_PR817/
EDC16_V50_PR818/EDC16_V58_PR818/EDC16_V5C_PR818/EDC16_V50_PR819/EDC16_V58_PR819/EDC16_V5C_PR819/
EDC16_V50_PR820/EDC16_V58_PR820/EDC16_V5C_PR820/EDC16_V50_PR821/EDC16_V58_PR821/EDC16_V5C_PR821/
EDC16_V50_PR822/EDC16_V58_PR822/EDC16_V5C_PR822/EDC16_V50_PR823/EDC16_V58_PR823/EDC16_V5C_PR823/
EDC16_V50_PR824/EDC16_V58_PR824/EDC16_V5C_PR824/EDC16_V50_PR825/EDC16_V58_PR825/EDC16_V5C_PR825/
EDC16_V18_PR816/EDC16_V1C_PR816/EDC16_V20_PR816/EDC16_V18_PR816/EDC16_V1C_PR817/EDC16_V20_PR817/
EDC16_V18_PR816/EDC16_V1C_PR818/EDC16_V20_PR818/EDC16_V18_PR819/EDC16_V1C_PR819/EDC16_V20_PR819/
EDC16_V18_PR820/EDC16_V1C_PR820/EDC16_V20_PR820/EDC16_V18_PR821/EDC16_V1C_PR821/EDC16_V20_PR821/
EDC16_V18_PR822/EDC16_V1C_PR822/EDC16_V20_PR822/EDC16_V18_PR823/EDC16_V1C_PR823/EDC16_V20_PR823/
EDC16_V18_PR824/EDC16_V1C_PR824/EDC16_V20_PR824/EDC16_V18_PR825/EDC16_V1C_PR825/EDC16_V20_PR825

13B-293
MR-372-J84-13B200$756.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of commands
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
SC002
ENTER INJECTOR CODES
NOTESrun this command after replacing the injectors but only if the vehicle is configured with
ima.
(ET104 Injector code use to YES).
If this command is not run, fault DF276 Injection code programming will be present.
WARNING
The letters J and Q, and figures 0 and 9 are not used in IMA coding.
If these characters are used the entry will be invalid.
Cylinder no. 1 is the cylinder located on the engine flywheel end.
Procedure to be followed:
– Make a note of the 6-character alphanumeric codes engraved on the upper section of the injector bodies.
– Use command SC002.
– Select the cylinder number for the cylinder concerned in the Desired, column, then confirm.
– enter the injector code displayed for the cylinder.
– Enter the new codes for each cylinder, then confirm.
– When the command is completed, the modified codes appear in the Current column.
– Check that the codes correspond to those read earlier.
– If the codes entered do not appear in either the Current column or the Desired column, check the codes read
and make sure that the data has been entered correctly.
The possible confusions are:
digit "1" with the letter "i"
figure 8 with the letter b
figure 5 with the letter s
- Exit fault finding mode.
- Switch off the ignition and wait for 1 min. Switch the ignition back on and check for faults.
-DF276 Injector code programming should be stored.
If fault DF276 Injector code programming is present, the command has not run correctly.
Start the procedure again and follow the instructions.
If the codes are still not accepted, check that the computer has been put on standby correctly:
Switch off the ignition and wait for 1 minute.
if the warning light flashes when the ignition is switched off, the computer has not been put on standby and the
command will be ignored.
If all these checks still do not enable the command to be confirmed, contact the Techline.
EDC16_V50_SC002/EDC16_V58_SC002/EDC16_V5C_SC002/EDC16_V18_SC002/EDC16_V1C_SC002/EDC16_V20_SC002

13B-317
MR-372-J84-13B200$792.mif
V13
13B
DIESEL INJECTION
Fault finding – Customer complaints
NOTESbefore dealing with this customer complaint, check that there are no faults, and check
the conformity (or otherwise) of the parameters and statuses using the diagnostic
tool.
if the customer complaint is not eliminated, then proceed according to the
corresponding fault finding chart.
no dialogue with engine management computer ALP 1
starting difficult or impossibleALP 2
injection noiseALP 3
poor performanceALP 4
irregular engine operationALP 5
external leaks from the fuel circuit ALP 6
rough idleALP 7
oil leaks from the turbochargerALP 8
particle filter warning light comes on too frequently ALP 9
noise from the turbochargerALP 10
smoke from the exhaustALP 11
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$792.mif