Et651 RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual

13B-162
MR-372-J84-13B200$468.mif
V13
13B
DIESEL INJECTION
Fault finding – Status summary table
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Pre-postheating unit control
ET014Monitor cooling fan 1
ET015Monitor cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111Number of passenger compartment heating resistors fixed (Vdiag 50 only)
ET112Passenger compartment heating resistors cut out (Vdiag 50 only)
ET143Low-speed fan assembly relay control (Vdiag 18, 1C, 20 only)
ET144High-speed fan assembly relay control (Vdiag 18, 1C, 20 only)
ET205Heating element no. 1 relay control (Vdiag 58 only)
ET206Heating element no. 2 relay control (Vdiag 58 only)
ET207Heating element no. 3 relay control (Vdiag 58 only)
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET415Cruise control/speed limiter deactivation
ET651EGR programming cut-off
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$468.mif

13B-200
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
EGR PROGRAMMING CUT-OFF
STATUS DEFINITIONThis status indicates the EGR valve programming cut-off.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80 °C
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
STATUS 1, 5, 6, 7, 9,
10, 12, 13, 15, 19
23, 24Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
STATUS 3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal (ET405 "Clutch pedal switch") is not pressed and that the
vehicle has stopped completely.
STATUS 4, 17Test the present and stored faults and repair.
STATUS 8Reset the EGR offsets by referring to the interpretation of command SC036
"Reinitialise programming" and select "EGR valve".
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_ET651/EDC16_V58_ET651/EDC16_V5C_ET651/EDC16_V18_ET651/EDC16_V1C_ET651/EDC16_V20_ET651

13B-201
MR-372-J84-13B200$540.mif
V13
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
CONTINUED
STATUS 11, 22
Allow the engine to heat up until this cut-off disappears.
STATUS 18Check that the regeneration of the particle filter in progress has completely finished.
STATUS 20Allow the engine to cool until this cut-off disappears.
STATUS 21Too low atmospheric pressure, the EGR valve is disabled.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.