service RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2011, Model line: SCENIC, Model: RENAULT SCENIC 2011 J95 / 3.GPages: 365, PDF Size: 2.11 MB
Page 1 of 365
1Engine and peripherals
V13 MR-372-J84-13B200$TOC.mif
V13
13B
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V13
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2011
DIESEL INJECTION
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20, 50, 58, 5C
Fault finding – Introduction 13B - 2
Fault finding – Cleanliness guidelines 13B - 9
Fault finding – System operation 13B - 11
Fault finding – Replacement of components 13B - 21
Fault finding – Configuration and programming 13B - 26
Fault finding – Fault summary table 13B - 27
Fault finding – Interpretation of faults 13B - 33
Fault finding – Conformity check 13B - 161
Fault finding – Status summary table 13B - 162
Fault finding – Interpretation of statuses 13B - 164
Fault finding – Parameter summary table 13B - 210
Fault finding – Interpretation of parameters 13B - 214
Fault finding – Command summary table 13B - 291
Fault finding – Interpretation of commands 13B - 292
Fault finding – Customer complaints 13B - 317
Fault finding – Fault Finding Chart 13B - 318
Fault finding – Tests 13B - 338
Fault finding – Glossary 13B - 365
Page 17 of 365
13B-17
MR-372-J84-13B200$108.mif
V13
DIESEL INJECTION
Fault finding – System operation
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
If regeneration whilst driving has not been possible, the driver should request After-Sales regeneration in the
following cases:
– the soot weight is greater than 56 g for Vdiag 18.
– the soot weight is greater than 59 g or the number of failed regenerations is greater than 10 for Vdiag 1C
and 20.
This regeneration is carried out in the workshop. It is essential to follow the instructions described in the
interpretation of commands SC017 Particle filter regeneration. To carry out regeneration safely (see Te c h n i c a l
Note 5040A, Recommendations for particle filter regeneration).
Warning light management:
Instrument panel display
The computer manages the data display on the instrument panel relating to engine operation. This involves six
functions:
– the pre-postheating warning light,
– the coolant temperature warning light or warning message;
– the level 1 fault warning light (non-critical fault),
– the level 2 fault warning light (emergency stop),
– the OBD warning light (European On Board Diagnostic),
– particle filter warning message or light.
These six functions are represented by 4 or 5 warning lights and/or messages displayed by the trip computer.
In addition, for vehicles fitted with a voice synthesiser the illumination of some warning lights may be accompanied
by a spoken message (refer to the Driver's Handbook for the vehicle concerned).
A 3 second visual inspection (automatic test procedure managed by the instrument panel) is carried out by the
injection computer when the ignition is switched on.
Orange pre-post heating/non-critical fault SERVICE warning light (level 1)
This light is used both as an in-operation indicator light and as a system fault indicator:
– Continuously lit with + after ignition feed:
Indicates plug preheating (this light goes out when preheating is complete and the engine is able to start).
– Continuously lit accompanied by the message Check injection or Electronic fault:
Indicates a level 1 fault (involving operation of the injection system in defect mode).
The driver should carry out repairs as soon as possible. IMPORTANT
The particle filter must be replaced after a period of time which largely depends on the grade of engine oil used.
This information is provided in the vehicle's Driver's handbook.
After replacing the particle filter, it is essential to reconfigure certain parameters in the computer (see SC036
Reinitialise programming).
Page 142 of 365
13B-142
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF312
CONTINUED 3
PA R T B
1 NO particle filter regeneration.
2 On the repair order, note the parameter and the status that correspond to the last failure:
– Mileage of the last DF312.
– Mileage of the last failures.
– Engine statuses of the last failures.
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED.
3 Interpretation of the values written on the order of repair by the service advisor for the customer:
Before the last time the warning light or Particle Filter message came on (appeared at the Mileage of the last
DF312), the customer had not respected the driving recommendations: the failure that occurred at the Mileage of
the last failure is due to the engine being switched off.
4 Check the weight of soot: PR383 Weight of soot in the particle filter.
If PR383
≥ 1 g. Apply the procedure for test 8 Manual clearing of the soot weight.
5 Explain to the customer the procedure to turn off the warning light, backed up by the parameters written in the
repair order: see PART D.
PA R T C
1- Carry out a regeneration in the Renault network with the approval of the Techline.
2- Change the oil and replace the oil filter if requested by a message on the diagnostic tool.
3- Run command SC036 Reinitialise programming and select After particle filter replacement.
4- Explain to the customer the procedure for regeneration when driving in order to avoid unnecessary repairs: see
PART D.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
Page 143 of 365
13B-143
MR-372-J84-13B200$360.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
DF312
CONTINUED 4
PA R T D
Procedure to switch off the Particle filter message or warning light on the instrument panel.
Certain types of driving can trigger the illumination of the particle filter warning light or message, and therefore
cause fault DF312 to appear. The customer must drive in a specific way (refer to vehicle's user manual) which
entails:
1. When the engine is warm, drive at a speed greater than 48 mph (80 km/h) for 2 minutes to trigger the
regeneration procedure.
2. Continue to drive at an average speed of 48 mph (80 km/h) until the "particle filter" message or warning light
on the instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without
stopping the engine or leaving the engine running at idle speed for an extended period of time. The
regeneration time depends on the vehicle and driving conditions but should last for 20 minutes maximum.
If regeneration when driving fails (the warning light has not switched off or the service warning light has come on),
carry out a particle filter regeneration in the Renault dealership. First, check the exhaust pipe for leaks or
blockage. Repair if necessary.
Run command SC017 Particle filter regeneration (see Interpretation of commands).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.