lock RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-2V9 MR-372-J84-13B450$010.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Procedure
To save energy, the vehicle's UCH interrupts the + after ignition feed after 3 minutes.
To run fault finding on a computer, it is possible to force the + after ignition feed for 1 hour by applying the following
procedure:
– press the unlocking button on the card,
– insert the card in the reader,
– press the start button (interrupting the timed + after ignition feed mode),
– press the start button for more than 5 seconds, without conditions for starting being met, until the immobiliser
warning light flashes rapidly (4 Hz).
This forced + after ignition feed mode is active for 1 hour.
Pressing the start button or removing the card from the card reader interrupts the forced + after ignition feed, but
does not interrupt the time period for the forced + after ignition feed. Until one hour has elapsed, activating the +
after ignition feed will restart forced + after ignition feed for the remaining time. Vehicle(s): MEGANE II phase 2, SCENIC II
phase 2Name of computer: BOSCH EDC16 C36
Engine: F9Q 816, 818Program No.: 91
Function concerned: DIESEL INJECTIONVdiag No.: 44, 4C, 48, 50, 54, 58
Special tooling required
Multimeter
Elé. 1681 Universal bornier
EDC16C36_V44_PRELI/EDC16C36_V4C_PRELI/EDC16C36_V48_PRELI/EDC16C36_V50_PRELI/EDC16C36_V54_PRELI/
EDC16C36_V58_PRELI
DIESEL INJECTION
Fault finding – Introduction

13B-6V9 MR-372-J84-13B450$010.mif
DIESEL INJECTION
Fault finding – Introduction13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
4.1 Connector check
1. Visual inspection of the connection:
– Check that the connector is connected correctly and that the male and female parts of the connection are correctly
coupled.
2. Visual inspection of the area around the connection:
– Check the condition of the mounting (pin, strap, adhesive tape, etc.) if the connectors are attached to the vehicle.
– Check that there is no damage to the wiring trim (sheath, foam, adhesive tape, etc.) near the wiring.
– Check that there is no damage to the electrical wires at the connector outputs, in particular on the insulating material
(wear, cuts, burns, etc.).
Disconnect the connector to continue the checks.
3. Visual inspection of the plastic casing:
– Check that there is no mechanical damage (casing crushed, cracked, broken, etc.), in particular to the fragile
components (lever, lock, terminal locations, etc.).
– Check that there is no heat damage (casing melted, blackened, deformed, etc.).
– Check that there are is no dirt (grease, mud, liquid, etc.).
4. Visual inspection of the metal contacts:
(The female contact is called CLIP. The male contact is called a TAB).
– Check that there are no bent contacts (the contact is not inserted correctly and can come out of the back of the
connector). The spring contact of the connector when the wire is pulled slightly.
– Check that there is no damage (tabs bent, clips open too wide, blackened or melted, etc.).
– Check that there is no oxidation on the metal contacts. Note:
Carry out each requested check visually. Do not remove a connector if it is not required.
Note:
Repeated connections and disconnections alter the functionality of the connectors and increase the risk of a poor
electrical contact. Restrict the number of connections/disconnections as far as possible.
Note:
The check is carried out on the 2 parts of the connection. There may be 2 types of connections:
– Connector/Connector.
– Connector/Device.

13B-18V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
b. The connections between the vehicle's various computers are multiplexed.
The electronic system fitted in this vehicle is multiplexed.
It enables dialogue between the various vehicle computers. As a result:
– the fault warning lights on the instrument panel are lit by the multiplex network,
– vehicle faults are displayed by the multiplex network,
– the vehicle speed sensor on the gearbox is not needed.
The vehicle speed signal on the instrument panel is sent by the ABS computer via the multiplex network. The vehicle
speed signal is mainly used by the injection computer, the airbag computer and the automatic transmission
computer (if the vehicle is fitted with this).
c. Functions hosted:
Air conditioning management assistance:
For vehicles with air conditioning, the EDC16C36 system provides the option of deactivating the air conditioning via
the UCH, under certain conditions of use:
– when requested by the driver,
– when starting the engine,
– if the engine overheats (in order to reduce the power the engine has to supply),
– when the engine speed is kept at a very high level (to protect the compressor),
– during transition phases (e.g. under heavy acceleration when overtaking, anti-stalling and moving off strategies).
These conditions are only taken into account when they do not occur repeatedly, in order to prevent system
instabilities (erratic deactivations), when certain faults appear.
Management of the damper valve:
The damper valve currently has three functions:
– the valve closes in order to block the passage of air towards the cylinders to shut off the engine. The aim of this is
to stop the engine as quickly as possible and to reduce instabilities as the engine is switched off.
– “valving” function depending on the engine operation: the damper valve closes by a few % to create a “'venturi”'
effect at the EGR valve passage section.
The aim of this is to accelerate the air flow of EGR gases and to reduce the emission of pollutants.
Thermoplunger management (only on certain F9Q816 engines in VDiag 48):
This vehicle is fitted with thermoplungers. They are managed and activated by the injection system.
There are two types of program:
– controlled by the injection system during particle filter regeneration,
– passenger compartment function; the air conditioning requests the injection to activate one or more thermoplungers
to raise the air temperature in the passenger compartment. The injection computer authorises the actuation or non-
actuation of the thermoplungers according to the operating phases and the power requirements of the engine.
The maximum number of thermoplungers that can be actuated is four. Their actuation depends mainly on the
coolant temperature (< 15°C) and the air temperature (< 5°C).

13B-112V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF091
PRESENT
OR
STOREDVEHICLE SPEED SIGNAL
1.DEF: Vehicle speed too high.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a road test.
Special notes:
– engine torque limited,
– the cruise control/speed limiter function is inhibited,
The vehicle speed signal sent by the ABS computer to the injection computer is greater
than the threshold defined in the calibration.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Check the condition of the ABS computer connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component Code 118 or 1094).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run full fault finding on the ABS (see 38C Anti-lock braking system).
Repair if necessary.
Run complete fault finding on the multiplex network (see 88B, Multiplexing).
Repair if necessary.
If the fault is still present, contact the Techline.
EDC16C36_V44_DF091/EDC16C36_V4C_DF091/EDC16C36_V48_DF091/EDC16C36_V50_DF091/EDC16C36_V54_DF091/
EDC16C36_V58_DF091
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-116V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF107
CONTINUED
Only for F9Q816:
If the vehicle is not new (mileage greater than 10 km):
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
– Do an after-sales regeneration using the control SC017 Particle filter regeneration.
– Perform an oil change (see MR 364 (Mégane II) or MR 370 (Scénic II), Mechanical, 10A Engine and
peripherals, Engine oil: Draining – Filling).
If the fault is still present, contact the Techline.

13B-125
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SENSOR CIRCUIT
1.DEF: No signal
2.DEF: Accelerator pedal sensor locked
3.DEF: Detection of accelerator pedal depressed at same time as brake pedal.
1.DEF
2.DEF
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor supply no. 2 voltage first, if
it is present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 1 second.
Special notes:
If the fault is present,
–the level 2 warning light illuminates if 1.DEF or 2.DEF is
present,
– turbocharging and cruise control are not authorised,
– the engine speed is fixed at 1400 rpm,
– cruise control/speed limiter function unusable,
– limitation of the quantity of fuel injected.
Use bornier Elé.1681 for any operations on the computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2.
EDC16C36_V44_DF165/EDC16C36_V4C_DF165/EDC16C36_V48_DF165/EDC16C36_V50_DF165/EDC16C36_V54_DF165/
EDC16C36_V58_DF165EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-148
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF228
CONTINUED 1
From the List of Statuses menu, check ET012 and ET013 and check:
– brake pedal in rest position ET012 = "RELEASED" and ET013 = "RELEASED"
– brake pedal depressed ET012 = "DEPRESSED" and ET013 = "DEPRESSED"
Has ET013 been correctly recognised?
Has ET012 been correctly recognised?Clear the fault
End of fault finding
procedure
Check the connections of the brake pedal switch, the ABS computer, the electronic stability program
computer and the engine management computer.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V after ignition feed on the connections of the brake pedal switch connector and the
condition of the fuse.
– Connection code AP10 of component 160.
– Connection code SP13 of component 160.
Disconnect the ABS - ESP and check the continuity and insulation against + 12 V and against earth
of the following connection:
– Connection code 65A between components 160 and 1094.
Check that the brake pedal switch is working correctly:
in rest position: infinite resistance continuity between the following connections:
– Connection code 65A of component 160.
– Connection code AP10 of component 160.
depressed: continuity between the following connections:
– Connection code 65A of component 160.
– Connection code AP10 of component 160.
Replace the switch if necessary.
If the fault is still present, carry out fault finding on the anti-lock braking system - electronic stability
program; if no irregularity is detected, then carry out fault finding on the multiplex network.
YES
YES
NONO
A
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-162
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF308
CONTINUED
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
Carry out an After-Sales regeneration.
Run command SC017 "Particle filter regeneration" (see Interpretation of commands).
Clear fault DF308 Present or Stored.
Apply TEST 4 Turbocharged air inlet circuit check.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-169
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF311
CONTINUED
The fault appears after 11 failed regeneration attempts when driving.
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
– Carry out an After-Sales regeneration.
– Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
– At the end of After-Sales regeneration, if the CLIP diagnostic tool indicates that you must replace the particle
filter, perform a oil change and replace the oil filter.
Explain to the customer the procedure for regeneration when driving to limit future garage repairs: see PART D in
the interpretation of DF312 Speed request.
If the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58

13B-173
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 3
PART B
1. No particle filter regeneration.
2. Write on the repair order the parameter and status relating to the last failure:
Mileage of last DF312
Mileage of last failures
Engine statuses of last failures
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3. Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the Particle Filter message or warning light illuminated (appeared at the Mileage of the
last DF312), the customer had not adhered to the driving recommendations: the failure that occurred at the
Mileage of the last failure is due to the engine being switched off.
4. Explain to the customer the procedure to turn off the warning light, making use of the parameters noted in the
repair order: see PA R T D.
PART C
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
Carry out an After-Sales regeneration with the consent of the Techline.
Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 58