manual transmission RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-243V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is no longer coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault-
finding on the R/0 control button located on the steering wheel, to the right.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-244V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 5
Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal that the brake pedal switch has been pressed.
If status ET415 is STATUS 5, consult the interpretation of statuses:
– ET042 Cruise control/speed limiter
– ET703 Cruise control/speed limiter buttons
– ET704 Brake switch No. 1
– ET705 Brake switch No. 2
to test the cruise control/speed limiter system components and find the defective
component.
Also, check the operation of the accelerator pedal, and use the diagnostic tool to
check the presence of a fault connected with this component. Deal with them if
necessary.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 changes to STATUS 5, deal with faults present or stored in the
injection computer.
If the fault is still present, contact the Techline.
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic
gearbox)
Status ET415 becomes STATUS 6, when driving with cruise control active
(ET042: Cruise control/speed limiter: CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into the neutral position on an automatic
transmission, test the ABS computer and check the configuration of the tyre size
stored in the computer.
If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58