ECU RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2011, Model line: SCENIC, Model: RENAULT SCENIC 2011 J95 / 3.GPages: 198, PDF Size: 0.85 MB
Page 103 of 198
13B-103V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 2):
*ECU: Electronic control unit
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Cruise control/
speed limiter
deactivationET415: Cruise
control - speed
limiter
deactivationNONE: This status is present on the diagnostic tool
when:
The computer has been reinitialised,
The computer has been reprogrammed.
- STATUS 1: Traction control request
- STATUS 2: Brake pedal depressed.
- STATUS 3: Clutch pedal depressed.
- STATUS 4: Suspend button pressed
- STATUS 5: Cruise control or speed limiter
monitoring.
- STATUS 6: Gear lever in neutral (manual gearbox)
or in the neutral position (automatic transmission).
- STATUS 7: Inconsistency between the request
and the vehicle speed.
- STATUS 8: Automatic transmission in defect
mode.
- STATUS 9: Vehicle speed monitoring.
- STATUS 10: Monitoring by the injection computer.In the event of a fault,
consult the
interpretation of status
ET415 Cruise
control - speed
limiter deactivation.
Page 106 of 198
13B-106V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS (continued 2):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Engine
immobiliserET003: Engine
immobiliser.
INACTIVEIndicates the status of the
immobiliser system.
- INACTIVE: The injection
computer has recognised the
immobiliser code transmitted by
the UCH.
- ACTIVE: The injection computer
has not recognised the
immobiliser code transmitted by
the UCH.If ACTIVE, apply
the associated Help given in
the tool.
Code
programmedET006: Code
programmed
YESIndicates whether the
immobiliser code has been
programmed into the computer.
- YES: Code is programmed.
- NO: Code was not programmed
into the injection computer.If NO, contact the Techline.
Vehicle speed PR089: Vehicle speedIndicates the vehicle speed in
mph. This parameter is
transmitted by the ABS
computer or by the vehicle
speed ECU. This signal is
transmitted to the injection
system on the multiplex
network.Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
New pump
chamber fillingET637: New pump
chamber fillingCOMPLETEDIf NOT DONE, see
Replacement of components.
Page 110 of 198
13B-110V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Refrigerant
pressurePR037:
Refrigerant
pressure.Gives the value in BAR for the
refrigerant fluid in the system.
2 bar < PR037 < 27 bar
Default value: 0 barIf there is a fault apply the
fault finding procedure for
DF049 "Refrigerant sensor
circuit". If the fault is still
present, replace the
refrigerant sensor.
Engine speedPR055: Engine
speed.
Cold: 900
RPM
Warm: 805 rpm.Shows the engine's speed of rotation in
RPMIn the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Fast idle speed
requestET023: Fast
idle speed
request.
ABSENTThe UCH requests fast idle speed from
the injection.
- ABSENT: The UCH did not make
a request.
- PRESENT: The UCH made a request.If ET023 is inconsistent, test
the multiplex network using
the diagnostic tool. If the test
is correct, consult the fault
finding procedure for the
UCH.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
Vehicle speedPR089: Vehicle
speed.Indicates the vehicle speed in mph.
This parameter is transmitted by the
ABS computer or by the vehicle speed
ECU. This signal is transmitted to the
injection system on the multiplex
network.Test the multiplex network.
Refer to fault finding for
the ABS or the vehicle speed
ECU.
Page 122 of 198
13B-122V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Brake contactET704: Brake
switch No. 1- INACTIVE
- ACTIVE (brake pedal depressed)Consult the interpretation of
status ET704 Brake switch
No. 1.
ET705: Brake
switch No. 2- ACTIVE (brake pedal released)
- INACTIVEConsult the interpretation of
status ET705 Brake switch
No. 2.
Clutch pedal
switchET405: Clutch
pedal switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the interpretation of
status ET405 Clutch
switch.
Cruise control
setpointPR130: Cruise
control
setpointIndicates the reference value requested by
the driver (in mph (km/h))NONE
Vehicle speedPR089: Vehicle
speed0 mph (km/h)
Gives the vehicle speed in mph (km/h). This
parameter is transmitted by the ABS computer
or vehicle speed ECU*. This signal is
transmitted to the injection on the multiplex
network.Test the multiplex
network. See fault finding
for the ABS system or the
vehicle speed ECU*.
Page 123 of 198
13B-123V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 2):
*ECU: Electronic control unit
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Cruise control -
speed limiter
deactivationET415: Cruise
control/speed
limiter
deactivationNONE: This status is present on the diagnostic
tool when:
The computer has been reinitialised,
The computer has been reprogrammed.
- STATUS 1: Traction control request
- STATUS 2: Brake pedal depressed.
- STATUS 3: Clutch pedal depressed.
- STATUS 4: Suspend button pressed
- STATUS 5: Cruise control or speed limiter
monitoring.
- STATUS 6: Gear lever in neutral
(manual gearbox) or neutral position
(automatic transmission).
- STATUS 7: Inconsistency between
the request and the vehicle speed.
- STATUS 8: Automatic transmission in defect
mode.
- STATUS 9: Vehicle speed monitoring.
- STATUS 10: Monitoring by the injection
computer.In the event of a fault,
consult the interpretation
of status ET415 "Cruise
control/speed limiter
deactivation".