battery RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals User Guide

13B-95V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperatureGives the external air
temperature in °C. This
parameter is controlled by
the UCH and transmitted to
the injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in
the UCH document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 30°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Battery
voltagePR074: Battery
voltage12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".

13B-104V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN STATUSES AND PARAMETERS OF THE COMPUTER:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".
Engine speedPR055: Engine
speed.
Cold: 900 rpm.
Warm: 805 rpm.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Accelerator
pedal positionPR030: Accelerator
pedal position.
0%Indicates the position of
the accelerator pedal as a %.
PR030 = 0 %In the event of a fault,
apply the fault finding
procedures for Pedal sensor
circuit gang 1 and gang 2
(DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperature.Gives the external air
temperature in °C. This
parameter is controlled by the
UCH and transmitted to the
injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in the
UCH document.
Inlet air
temperaturePR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 20°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.

13B-107V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
STARTING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
+ After ignition
computer feedET001: + After ignition
computer feed.
PRESENTIndicates + after ignition feed to
the computer.
- Present
- AbsentIn the event of a fault, carry
out the fault finding
procedure for DF047
"Computer supply voltage" or
DF015 "Main relay circuit".
StartingET076: Starting.
AUTHORISEDIndicates whether or not
starting has been authorised by
the injection.
AUTHORISED: The injection
authorises starting.
PROHIBITED: The injection
does not authorise starting.If PROHIBITED, carry out
a complete fault finding
procedure on the preheating
system.
EngineET038: Engine.
RUNNINGIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a fault has
appeared or when the engine
speed is locked at a certain
value.NONE
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply
the fault finding procedure for
the "Charge circuit".

13B-108V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PROTECTION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Engine
immobiliserET003: Engine
immobiliser.
INACTIVEIndicates the status of the
immobiliser system.
- INACTIVE: The injection
computer has recognised the
immobiliser code transmitted by
the UCH.
- ACTIVE: The injection computer
has not recognised the
immobiliser code transmitted by
the UCH.If ACTIVE, apply
the associated Help given in
the tool.
Code
programmedET006: Code
programmed
YESIndicates whether the
immobiliser code has been
programmed into the computer.
- YES: Code is programmed.
- NO: Code was not programmed
into the injection computer.If NO, contact the Techline.
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply
the fault finding procedure for
the "Charge circuit".

13B-115V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the
interpretation of
parameter PR064
Coolant temperature.
External air
temperaturePR061: External air
temperature.Gives the external air temperature
in °C. This parameter is controlled
by the UCH and transmitted to the
injection via the multiplex network.
Default value: 20°CIn the event of a fault,
apply the fault finding
procedure for this fault
described in the UCH
document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Battery voltage PR074: Battery voltage.12 V < PR074 < 14 VIf there is a fault, apply
the fault finding
procedure for the
"Charge circuit".

13B-143V4 MR-372-J84-13B000$100.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
* Heat.: HeatingTool parameter DIAGNOSTIC TOOL DESCRIPTION
PR005 EGR valve opening setpoint
PR008 Rail pressure set point
PR009 Turbocharging pressure setpoint
PR010 Idle speed regulation setpoint
PR017 Fuel flow
PR073 Air flowmeter supply voltage
PR028 Pedal position (gang 1)
PR029 Pedal position (gang 2)
PR030 Accelerator pedal position
PR032 Inlet pressure
PR035 Atmospheric pressure
PR037 Refrigerant pressure
PR038 Rail pressure
PR051 EGR valve position feedbac
PR055 Engine speed
PR059 Inlet air temperature (invalid in K9K 728)
PR061 External air temperature
PR063 Fuel temperature
PR064 Coolant temperature
PR074 Battery voltage
PR077 EGR valve position sensor voltage
PR080 Rail pressure sensor voltage
PR081 Inlet temperature sensor voltage
PR088 Pedal potentiometer gang 2 voltage
PR089 Vehicle speed
PR125 Power absorbed by air conditioning compressor
PR127 Heat.* resistor maximum authorised power
PR130 Cruise control setpoint
PR132 Air flow
DIESEL INJECTION
Fault finding – Parameter summary table

13B-149V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 2 Electrical circuit check
Check the battery charge and that the alternator is
operating correctly (see 87G, Engine compartment
connection unit for Mégane II or Scénic II).
Is the charging circuit in good order? Carry out the necessary repairs
Check the fuses.
Are the fuses correct? Carry out the necessary repairs
Check that the injection locking relay is operating
correctly.
Is the injection locking relay working properly? Carry out the necessary repairs
Check the engine earths.
Are the engine earths correct?Carry out the necessary repairs
The electrical circuit is in good order.
NO
YES
NO
YES
NO
YES
NO
YES
DDCR_V44_TEST02/DDCR_V48_TEST02

13B-166
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
13B
InjectionDDCR
Vdiag No.: 44, 48
ALP1 No dialogue with the computer
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
To check that the diagnostic tool is not causing the fault, try to establish dialogue with a computer on another
vehicle. If the diagnostic tool is not the cause and communication cannot be established with any other computer
on the same vehicle, it is possible that another computer is disrupting the multiplex network. Check the battery
voltage and make the necessary adjustments to obtain a correct voltage (9.5 V < Battery voltage < 17.5 V).
Carry out fault finding on the multiplex network using the diagnostic tool (see 88B, Multiplexing).
Check the presence and the condition of the injection fuses on the UPC and on the engine fuse box.
Check the connection of the computer connectors and the condition of its connections.
Check the injection computer earths (quality, oxidation, tightness of earth bolts on the battery terminal).
Check that the supply to the computer is correct:
–AP15 between components 1337 and 120,
–NH between earth and component 120,
–3FB1 between components 1337 and 120,
–3FB2 between components 1337 and 120.
Ensure that the supply to the diagnostic socket is correct:
–BP32 between components 225 and 260,
–AP43 between components 225 and 1337,
–MN between earth and component 225,
If dialogue has still not been established after these checks, contact the techline.
DDCR_V44_ALP01/DDCR_V48_ALP01
DIESEL INJECTION
Fault finding – Fault finding charts