gearbox RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Workshop Manual

13B-21V4 MR-372-J84-13B000$040.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
SETTINGS
VP001: Cylinder 1 injector code.
VP002: Cylinder 2 injector code.
VP003: Cylinder 3 injector code.
VP004: Cylinder 4 injector code.
These commands enable you to manually write the calibration code inscribed on the injector. Use these commands
after replacing an injector or replacing or (re)programming the computer, when command SC001 does not work.
VP010: Enter VIN.
This command permits manual entry of the vehicle's VIN into the computer. Use this command each time
the computer is replaced or (re)programmed.
SPECIAL COMMANDS
SC001: Write saved data.
Use this command after replacing or (re)programming a computer (if the information was saved using SC003).
SC002: Enter injector codes.
This command enables you to manually write the calibration code inscribed on the injectors. Use this command after
replacing the injectors.
SC003: Save computer data.
This command saves the computer's operating data, the C2I (individual injector correction) parameters,
and the engine adaptives. Use this command before replacing or (re)programming the computer.
OTHER COMMANDS
LC005: Gearbox type. This command enables you to determine the gearbox type configured on the vehicle.
LC120: Cruise control. With or without
LC121: Speed limiter. With or without
DIESEL INJECTION
Fault finding – Configurations and programming

13B-103V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 2):
*ECU: Electronic control unit
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Cruise control/
speed limiter
deactivationET415: Cruise
control - speed
limiter
deactivationNONE: This status is present on the diagnostic tool
when:
The computer has been reinitialised,
The computer has been reprogrammed.
- STATUS 1: Traction control request
- STATUS 2: Brake pedal depressed.
- STATUS 3: Clutch pedal depressed.
- STATUS 4: Suspend button pressed
- STATUS 5: Cruise control or speed limiter
monitoring.
- STATUS 6: Gear lever in neutral (manual gearbox)
or in the neutral position (automatic transmission).
- STATUS 7: Inconsistency between the request
and the vehicle speed.
- STATUS 8: Automatic transmission in defect
mode.
- STATUS 9: Vehicle speed monitoring.
- STATUS 10: Monitoring by the injection computer.In the event of a fault,
consult the
interpretation of status
ET415 Cruise
control - speed
limiter deactivation.

13B-123V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
CRUISE CONTROL - SPEED LIMITER SUB-FUNCTION (continued 2):
*ECU: Electronic control unit
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Cruise control -
speed limiter
deactivationET415: Cruise
control/speed
limiter
deactivationNONE: This status is present on the diagnostic
tool when:
The computer has been reinitialised,
The computer has been reprogrammed.
- STATUS 1: Traction control request
- STATUS 2: Brake pedal depressed.
- STATUS 3: Clutch pedal depressed.
- STATUS 4: Suspend button pressed
- STATUS 5: Cruise control or speed limiter
monitoring.
- STATUS 6: Gear lever in neutral
(manual gearbox) or neutral position
(automatic transmission).
- STATUS 7: Inconsistency between
the request and the vehicle speed.
- STATUS 8: Automatic transmission in defect
mode.
- STATUS 9: Vehicle speed monitoring.
- STATUS 10: Monitoring by the injection
computer.In the event of a fault,
consult the interpretation
of status ET415 "Cruise
control/speed limiter
deactivation".

13B-132
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 1
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the brake pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult
the interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, MULTIPLEXING).

13B-135
AFTER REPAIRCarry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$090.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DDCR INJECTION
Vdiag No.: 44, 48
ET415
CONTINUED 4
STATUS 6
Gear lever in neutral (manual gearbox) or the neutral position
(automatic gearbox)
Status ET415 becomes STATUS 6 when driving with cruise control active
(ET042 Cruise control - speed limiter: CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of
the tyre size stored in the computer. If the configuration is correct, contact the
Techline.
STATUS 7Inconsistency between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference in
speed.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 7 on relatively flat terrain, contact the Techline.

13B-191
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP16 Engine rattling, noisy engine, turbocharger noise
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
If the noise arises from the turbocharger, apply Technical Note 5164A, Noise fault finding.
Note:
Pay close attention to faulty components that might result in unjustified replacement of the turbocharger. For
example, whistling does not necessarily indicate damage to the turbocharger (this could be coming from the
exhaust, the timing, the gearbox, etc.).
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Is the compression in order? Carry out the necessary repairs.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
NO
YES
A
DDCR_V44_ALP16/DDCR_V48_ALP16