sensor RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Owner's Manual

13B-43
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF027
CONTINUED
YES
Injector 2 is not faulty, the fault is in the injector 2 control circuit.
Check the continuity, insulation, and the absence of interference resistance on
the following connections:
Computer connector B track G4 Track 1 injector 2
Computer connector B track H4 Track 2, injector 2
Repair if necessary.
If the fault is still present, contact the Techline.
NOInjector 2 is faulty, replace the cylinder 2 injector.
1.DEF
NOTESNone.
Check the conformity of the injectorsfitted to the vehicle in relation to the type of vehicle and engine number (low,
high or very high injector pressure).
Check that the C2I is correctly entered on the computer.
Check the accelerometer shielding on track K1 of the brown 48-track connector B of the computer.
Check that the accelerometer is secured on the engine.
After retightening the accelerometer, it is essential to clear the pressure regulation adaptives using command
RZ004 Pressure regulation adaptives.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
If the fault is still present, replace the cylinder 2 injector.

13B-45
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF028
CONTINUED
YES
Injector 3 is not faulty, the fault is in the injector 3 control circuit.
Check the continuity, insulation, and the absence of interference resistance on
the following connections:
Computer connector B track C4 Track 1 injector 3
Computer connector B track D4 Track 2, injector 3
Repair if necessary.
If the fault is still present, contact the Techline.
NOInjector 3 is faulty, replace the cylinder 3 injector.
1.DEF
NOTESNone.
Check the conformity of the injectorsfitted to the vehicle in relation to the type of vehicle and engine number (low,
high or very high injector pressure).
Check that the C2I is correctly entered on the computer.
Check the accelerometer shielding on track K1 of the brown 48-track connector B of the computer.
Check that the accelerometer is secured on the engine.
After retightening the accelerometer, it is essential to clear the pressure regulation adaptives using command
RZ004 Pressure regulation adaptives.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
If the fault is still present, replace the cylinder 3 injector.

13B-47
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF029
CONTINUED
YES
Injector 4 is not faulty, the fault is in the injector 4 control circuit.
Check the continuity, insulation, and the absence of interference resistance on
the following connections:
Computer connector B track E4 Track 1 injector 4
Computer connector B track F4 Track 2, injector 4
Repair if necessary.
If the fault is still present, contact the Techline.
NOInjector 4 is faulty, replace the cylinder 4 injector.
1.DEF
NOTESNone.
Check the conformity of the injectorsfitted to the vehicle in relation to the type of vehicle and engine number (low,
high or very high injector pressure).
Check that the C2I is correctly entered on the computer.
Check the accelerometer shielding on track K1 of the brown 48-track connector B of the computer.
Check that the accelerometer is secured on the engine.
After retightening the accelerometer, it is essential to clear the pressure regulation adaptives using command
RZ004 Pressure regulation adaptives.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
If the fault is still present, replace the cylinder 4 injector.

13B-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF039
PRESENTINLET AIR TEMPERATURE SENSOR CIRCUITCO.1: Open circuit or short circuit to + 12 volts.
CC.0: Short circuit to earth.
NOTESPriority when dealing with a number of faults:
– Deal with fault DF113 Sensor supply voltage first.
Check the connection and condition of the 4-track connector of the air temperature sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Measure the resistance between tracks 1 and 2 on the air temperature sensor.
Replace the air temperature sensor if the resistance is not 2051 Ω +
120 Ω at 25°C.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track C3 computer connector B
Sensor connector track 2 Track J2 computer connector B
Sensor connector track 3 Track C1 computer connector B
Sensor connector track 4 Track C2 computer connector B
Repair if necessary.
DDCR_V44_DF039P/DDCR_V48_DF039P

13B-53
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF049
STOREDREFRIGERANT SENSOR CIRCUITCO.1: Open circuit or short circuit to + 12 volts.
CC.0: Short circuit to earth.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present when the engine is running and the air conditioning is on.
Priority when dealing with several faults: - Deal first with fault DF113 Sensor supply
voltage.
Check the connection and condition of the refrigerant pressure sensor connector.
Repair if necessary.
Check the connection and condition of the computer's 32-track grey connector C.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track BTrack C4 computer connector C
Sensor connector track CTrack C3 computer connector C
Sensor connector track ATrack C3 computer connector C
Repair if necessary.
DDCR_V44_DF049M/DDCR_V48_DF049M

13B-58
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
DF053
STOREDRAIL PRESSURE REGULATION FUNCTION
1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: High flow current < minimum
6.DEF: High flow current > maximum
7.DEF: Low flow current < minimum
8.DEF: Low flow current > minimum
NOTESSpecial notes:
If DF053, the engine may stop, with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Priority when dealing with a number of faults:
– DF007 Rail pressure sensor circuit,
– DF098. Fuel temperature sensor circuit.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
4.DEF
6.DEF
8.DEF
NOTESNone.
Check the connection and condition of the fuel flow actuator connector (brown IMV connector on the pump).
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω +
0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity, and the absence of interference resistance on the following connection:
Computer connector B track M4 Track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
DDCR_V44_DF053M/DDCR_V48_DF053M
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-61
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF056
PRESENT
OR
STOREDAIR FLOW SENSOR CIRCUIT1.DEF: Permanent low level
2.DEF: Permanent high signal
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: At minimum limit
6.DEF: At maximum limit
NOTESPriority when dealing with a number of faults:
– DF054 Turbocharging solenoid valve control circuit.
– DF113 Sensor supply voltage.
Conditions for applying fault finding procedures to stored faults:
the fault reappears after the faults have been cleared followed by a road test.
Check the condition of the air filter, and replace it if necessary.
Check that the inlet manifold is not blocked (clogged).
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Carry out the necessary repairs.
Check the connection and condition of the 6-track connector of the air flow sensor.
Repair if necessary.
Check for +5 V after ignition feed on track 3 of the sensor connector.
Repair if necessary.
Check for +12 V on track 4 of the sensor connector.
Repair if necessary.
Check for earth on connector track 6.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
DDCR_V44_DF056/DDCR_V48_DF056

13B-62
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF056
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track K2 computer connector B
Sensor connector track 2 Track A3 computer connector B
Sensor connector track 3 Track A1 computer connector B
Sensor connector track 4 Track A2 computer connector B
Sensor connector track 5 + after ignition feed
Sensor connector track 6Earth
Repair if necessary.
Also check the insulation between these connections.
If the fault is still present, replace the air flow sensor.

13B-63
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF057
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUITCO.1: Open circuit or short circuit to +12 volts
CC.0: Short circuit to earth
1.DEF: Above maximum threshold (water present)
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
The level 1 warning light illuminates along with the message Check diesel filter.
CO.1
CC.0
NOTESNone.
Check for water in the diesel filter. Clean and replace the filter if necessary.
Check the condition and connection of the 3-track connector of the water detector.
Repair if necessary.
Check the connection and condition of the grey 32-track connector C of the computer.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 3 Earth
Sensor connector track 2 Track B3 computer connector C
Sensor connector track 1 Track A3 computer connector B
Repair if necessary.
1.DEF
NOTESNone.
Bleed the diesel filter.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
DDCR_V44_DF057M/DDCR_V48_DF057M

13B-68
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF089
PRESENTINLET MANIFOLD PRESSURE SENSOR CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: Inconsistency
6.DEF: At maximum limit
7.DEF: At minimum limit
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
The level 1 warning light illuminates along with the message Faulty injection.
K9K 722 ENGINE
1.DEF-2.DEF
3.DEF-4.DEF
NOTESNone.
Check the connection and condition of the 4-track connector of the inlet pressure sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 track C3 computer connector B
Sensor connector track 2 track J2 computer connector B
Sensor connector track 3 track C1 computer connector B
Sensor connector track 4 track C2 computer connector B
Repair if necessary.
DDCR_V44_DF089P/DDCR_V48_DF089P