air RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Manual Online

13B-91V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
* When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph, and high coolant temperature). The fan assemblies are disabled under certain coolant temperature
conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Vehicle speedPR089: Vehicle
speed.Indicates the vehicle speed in mph.
This parameter is transmitted by the
ABS computer or by the vehicle
speed ECU. This signal is
transmitted to the injection system
on the multiplex network.Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the air
conditioning
compressor.
0 WIndicates the power consumed by
the compressor.NONE
Speed request
for fan
assembly*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed, correct refrigerant pressure
and vehicle speed = 0 mph (km/h),
or high coolant temperature.NONE
Speed request
for fan
assembly*ET021: High speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed. Refrigerant pressure
> 15 bar, vehicle speed = 0 mph,
or high coolant temperature.NONE

13B-95V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperatureGives the external air
temperature in °C. This
parameter is controlled by
the UCH and transmitted to
the injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in
the UCH document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 30°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Battery
voltagePR074: Battery
voltage12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".

13B-96V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
AIR CIRC. SUB-FUNCTION (TURBO/INLET):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 30°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Air circuit
pressurePR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.If not consistent, check that
PR035 = PR032 =
local atmospheric pressure,
with the engine stopped
and the ignition on. PR032: Inlet
pressure.Indicates the pressure in
the inlet circuit in mbar.
Air flow PR132: Air flow.Air flow estimated by
the injection computer.NONE
Inlet
temperature
sensor voltagePR081: Inlet
temperature sensor
voltage.Indicates the voltage, in volts,
delivered by the computer to
supply the inlet temperature
sensor.NONE
Engine speedPR055: Engine
speed.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".

13B-99V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
EMISSION CONTROL/OBD SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
EGR valve
controlET008: EGR valve
control.
INACTIVEIndicates the EGR valve control
status.
- INACTIVE: The valve is not
controlled by the computer.
- ACTIVE: The valve is controlled
by the computer.NONE
Atmospheric
pressurePR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.If not consistent, check that
PR035 = PR032 = local
atmospheric pressure, with
the engine stopped
and the ignition on.
Air flow PR132: Air flow.Air flow estimated by the
injection computer.NONE
Fuel flowPR017: Fuel flow.
0.0 mg/stGives the fuel flow at the high
pressure pump outlet in mg/st.NONE
EGR valve
opening
setpointPR005: EGR valve
opening setpoint.
Warm or cold = -50Gives a theoretical EGR valve
opening value for optimum
engine operation.
PR005 = PR051NONE
EGR valve
position
feedbackPR051: EGR valve
position feedback.
Warm or cold = -50Shows the true EGR valve
position.
PR051 = PR005NONE

13B-104V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN STATUSES AND PARAMETERS OF THE COMPUTER:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".
Engine speedPR055: Engine
speed.
Cold: 900 rpm.
Warm: 805 rpm.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Accelerator
pedal positionPR030: Accelerator
pedal position.
0%Indicates the position of
the accelerator pedal as a %.
PR030 = 0 %In the event of a fault,
apply the fault finding
procedures for Pedal sensor
circuit gang 1 and gang 2
(DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperature.Gives the external air
temperature in °C. This
parameter is controlled by the
UCH and transmitted to the
injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in the
UCH document.
Inlet air
temperaturePR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 20°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.

13B-105V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Fuel
temperaturePR063: Fuel
temperature.
Cold = PR064
Warm: 50°CGives the fuel temperature
in °C. This value is supplied by
"the fuel temperature sensor".
Default value: 30°C.In the event of a fault, apply
the fault finding procedure for
fault DF098 "Fuel temperature
sensor circuit".
Air circuit
pressure.PR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.
600 mbar < Cold < 1050 mbar
600 mbar < Warm < 1050 mbar.If not consistent, check that
PR035 = PR032 = local
atmospheric pressure, with
the engine stopped and
the ignition on.
PR032: Inlet pressure.Indicates the pressure in the
inlet circuit in mbar.
PR032 = Local atmospheric
pressure.
Rail pressurePR038: Rail pressure.
Cold: 260 bar.
Warm: 230 bar.Indicates the pressure, in bar, of
the diesel fuel in the injector
rail. This pressure is supplied
by the sensor on the rail.
Default value: 2000 barIn the event of a fault apply
the fault finding procedure for
fault DF007 "Rail pressure
sensor circuit".
EngineET038: Engine
runningIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine has
stalled.
- PROTECTED: When a level 2
fault has appeared or when the
engine speed is locked at
a certain value.NONE

13B-109V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check
or actionDisplay and notes Fault finding
Air conditioning
presentET079: Air
conditioning
present.
YESIndicates whether the vehicle is fitted with air
conditioning or not.
- YES: Air conditioning is detected by the injection
computer.
- NO: Air conditioning is not detected by the
injection computer.If inconsistent with
the vehicle
equipment, perform
a multiplex network
test and apply the
associated
procedure.
Compressor
activation
requestET088:
Compressor
activation
request.
INACTIVEThe injection requests the Protection and
Switching Unit (via the multiplex network) to
start the compressor.
- ACTIVE: The multiplex network must not be faulty
on the Automatic transmission, Protection and
Switching Unit, or UCH systems. The UCH should
request the injection to be engaged. The coolant
pressure sensor must not be defective. Satisfactory
engine operating conditions (coolant temperature,
engine load etc.).
- INACTIVE: One of the above conditions has not
been met or no request has been made by the
driver, so ET004 = NO.NONE
Air conditioning
authorisedET004: Air
conditioning
authorised.
NONon operational information, designed solely
for fault finding purposes.
- YES: Satisfactory engine operating conditions
(coolant temperature, engine load, etc.). The
vehicle is not in a specific movement phase (hill
start, start from stop etc.).
- NO: One of the above conditions has not been
met or no request has been made by the driver, so
ET088 = INACTIVE.NONE

13B-111V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
*When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph (0 km/h) and high coolant temperature). The fan assemblies are disabled under certain coolant
temperature conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check or
actionDisplay and notes Fault finding
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the
air conditioning
compressor.
0 WATTIndicates the power consumed by the
compressor.NONE
Fan assembly
speed request*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Correct refrigerant pressure and vehicle speed
= 0 mph (0 km/h) or high coolant temperature).
NONE
ET021: High
speed fan
assembly request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Refrigerant pressure > 15 bar and vehicle speed
= 0 mph or high engine coolant temperature).

13B-115V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the
interpretation of
parameter PR064
Coolant temperature.
External air
temperaturePR061: External air
temperature.Gives the external air temperature
in °C. This parameter is controlled
by the UCH and transmitted to the
injection via the multiplex network.
Default value: 20°CIn the event of a fault,
apply the fault finding
procedure for this fault
described in the UCH
document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Battery voltage PR074: Battery voltage.12 V < PR074 < 14 VIf there is a fault, apply
the fault finding
procedure for the
"Charge circuit".

13B-116V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
AIR CIRC. SUB-FUNCTION (TURBO/INLET):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Inlet air
temperature
(invalid for
K9K 728)PR059:
Inlet air temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Air circuit
pressure.PR035: Atmospheric
pressure.Indicates the atmospheric pressure
in mbar. The sensor is built into
the computer.If not consistent, check
that PR035 = PR032 =
local atmospheric
pressure, with the
engine stopped and the
ignition on. PR032: Inlet pressure.Indicates the pressure in the inlet
circuit in mbar.
Air flow.PR132: Air flow.
350 < Cold < 400 mg/st
300 < Cold < 350 mg/stAir flow estimated by the injection
computer.NONE
Inlet temperature
sensor voltagePR081: Inlet temperature
sensor voltage.Indicates the voltage, in volts,
delivered by the computer to
supply the inlet temperature
sensor.NONE
Engine speedPR055: Engine speed.
Cold: 900 rpm.
Warm: 805 rpmIndicates the engine's speed of
rotation in rpm.In the event of a fault,
apply the fault finding
procedure for
DF005 "Engine speed
sensor circuit".