pressure RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Owners Manual

13B-383V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR290AC REFRIGERANT PRESSURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the refrigerant pressure sensor voltage in volts.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The refrigerant pressure sensor voltage value must be between:
0 V ≤ PR290 ≤ 5 V.
Carry out fault finding on the climate control computer (see62B, Climate control).
EDC16CP33_V18_PR290 / EDC16CP33_V1C_PR290 / EDC16CP33_V54_PR290 / EDC16CP33_V20_PR290 / EDC16CP33_V58_PR290 /
EDC16CP33_V5C_PR290 / EDC16CP33_V24_PR290 / EDC16CP33_V60_PR290 / EDC16CP33_V62_PR290
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-388V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
diff.*: differential
PR383WEIGHT OF SOOT IN PARTICLE FILTER
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in the particle filter in g.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the weight of soot in the particle filter must be:
PR383 < 56 g.
If the weight is greater than 56 g:
For all Vdiags (except 18): carry out an After-Sales regeneration. Run command SC017 Particle filter
regeneration and follow the procedure (see Interpretation of commands).
For Vdiag 18:
Reprogram the computer in Vdiag 1C.
Then apply the procedure corresponding to Vdiag 1C.
In the event of a fault, refer to the interpretation of fault DF315 Particle filter diff* pressure sensor.
EDC16CP33_V18_PR383 / EDC16CP33_V1C_PR383 / EDC16CP33_V54_PR383 / EDC16CP33_V20_PR383 / EDC16CP33_V58_PR383 /
EDC16CP33_V5C_PR383 / EDC16CP33_V24_PR383 / EDC16CP33_V28_PR383 / EDC16CP33_V62_PR383 / EDC16CP33_V26_PR383 /
EDC16CP33_V60_PR383
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-394V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
diff.*: differential
PR414PARTICLE FILTER DIFF* PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESNone.
Conformity check: Engine stopped and ignition on
The value of the particle filter differential pressure must be between:
- 1 mbar < PR414 < 1 mbar
In the event of a fault, refer to the interpretation of fault DF315 Particle filter diff* pressure sensor.
Conformity check with the engine running and engine coolant temperature > 80°C
The value of the particle filter differential pressure must be between:
10 mbar < PR414 < 100 mbar
In the event of a fault, refer to the interpretation of fault DF315.
EDC16CP33_V18_PR414 / EDC16CP33_V1C_PR414 / EDC16CP33_V54_PR414 / EDC16CP33_V20_PR414 / EDC16CP33_V58_PR414 /
EDC16CP33_V5C_PR414 / EDC16CP33_V24_PR414 / EDC16CP33_V28_PR414 / EDC16CP33_V62_PR414 / EDC16CP33_V26_PR414 /
EDC16CP33_V60_PR414
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-396V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
OCR*: Opening Cyclic Ratio
PR484FUEL REGULATION SOLENOID VALVE OCR*
PARAMETER
DEFINITIONThis parameter indicates the solenoid valve opening ratio as a %.
Conformity check with engine stopped and ignition on.
The value of the solenoid valve opening ratio must be:
PR484 = 0%.
In the event of a fault, consult the interpretation of DF897 Pump pressure regulator circuit.
Conformity check: Engine running, engine coolant temperature > 80°C
The solenoid valve opening value must be between:
30% < PR484 < 40%.
In the event of a fault, refer to the interpretation of fault DF897.
EDC16CP33_V18_PR484 / EDC16CP33_V1C_PR484 / EDC16CP33_V54_PR484 / EDC16CP33_V20_PR484 / EDC16CP33_V58_PR484 /
EDC16CP33_V5C_PR484 / EDC16CP33_V24_PR484 / EDC16CP33_V04_PR484 / EDC16CP33_V08_PR484 / EDC16CP33_V44_PR484 /
EDC16CP33_V4C_PR484 / EDC16CP33_V34_PR484 / EDC16CP33_V38_PR484 / EDC16CP33_V74_PR484 / EDC16CP33_V28_PR484 /
EDC16CP33_V62_PR484 / EDC16CP33_V26_PR484 / EDC16CP33_V60_PR484
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-401V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR739FUEL FLOW SOLENOID VALVE CURRENT
PARAMETER
DEFINITIONThis parameter indicates the current absorbed by the fuel flow solenoid valve inmA.
Conformity check with engine stopped and ignition on.
The value of the current absorbed by the fuel flow solenoid valve must be:
PR739 ≈ 200 mA.
In the event of a fault, consult the interpretation of DF897 Pump pressure regulator circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
The value of the current absorbed by the fuel flow solenoid valve must be:
PR739 ≈ 300 mA.
In the event of a fault, refer to the interpretation of fault DF897.
EDC16CP33_V18_PR739 / EDC16CP33_V1C_PR739 / EDC16CP33_V54_PR739 / EDC16CP33_V20_PR739 / EDC16CP33_V58_PR739 /
EDC16CP33_V5C_PR739 / EDC16CP33_V24_PR739 / EDC16CP33_V04_PR739 / EDC16CP33_V08_PR739 / EDC16CP33_V44_PR739 /
EDC16CP33_V4C_PR739 / EDC16CP33_V34_PR739 / EDC16CP33_V38_PR739 / EDC16CP33_V74_PR739 / EDC16CP33_V28_PR739 /
EDC16CP33_V62_PR739 / EDC16CP33_V26_PR739 / EDC16CP33_V60_PR739
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-403V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR782TURBINE UPSTREAM PRESSURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the turbine upstream pressure sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The turbine upstream pressure sensor voltage value must be between:
PR782 ≈ 5 V.
In the event of a fault consult the interpretation of fault DF651 Turbine upstream pressure sensor circuit.
EDC16CP33_V18_PR782 / EDC16CP33_V1C_PR782 / EDC16CP33_V54_PR782 / EDC16CP33_V20_PR782 / EDC16CP33_V58_PR782 /
EDC16CP33_V5C_PR782 / EDC16CP33_V24_PR782 / EDC16CP33_V28_PR782 / EDC16CP33_V62_PR782 / EDC16CP33_V26_PR782 /
EDC16CP33_V60_PR782
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-422V12 MR-372-J84-13B300$140.mif
13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
NOTESThe commands are run to check the correct operation of certain components or to
replace parts.
Tool command Diagnostic tool title
SC001Write saved data
SC002Enter injector codes
SC003Save computer data
SC017Particle filter regeneration (except Vdiag 18, 04, 08, 44, 4C, 34, 38, 74)
SC031Operational fault finding of cylinders (except Vdiag 18)
SC035High pressure fuel circuit fault finding
SC036Reinitialise programming
RZ001Fault memory
RZ005Programming
RZ034Computer memory
AC004Turbocharging solenoid valve
AC012Damper valve
AC031Thermoplunger No. 3 relay
AC037Preheating relay
AC063Thermoplunger No. 1 relay
AC064Thermoplunger No. 2 relay
AC103EGR by-pass
AC153High speed fan assembly (except Mégane II ph2 and Scénic II ph2)
AC154Low speed fan assembly (except Mégane II ph2 and Scénic II ph2).
AC195Electric coolant pump (except Vdiag 04, 08, 44, 4C, 34, 38, 74)
AC225Rail pressure regulator
AC226Pump pressure regulator.
MT001Turbocharging function (Vdiag 04 and 44 only)
VP010Write VIN
VP036Fuel supply inhibited
DIESEL INJECTION
Fault finding – Command summary table

13B-429V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 2
VALIDATING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
•Particle filter regeneration finished:
Consult PR1012 Weight of soot after regeneration. If this parameter is less than 15 g, the particle filter
regeneration was successful. If PR1012 is greater than 15 g, it is necessary to carry out a second particle filter
regeneration using the diagnostic tool and run command SC017.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool
down for 2 hours with the bonnet open.
Do not carry out an engine oil change before a second After-Sales regeneration.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other VDiag:
Consult PR848 Number of regeneration failures. If PR848 is greater than 3, change the engine oil.
Particle filter too full - replace the particle filter: regeneration has failed. The weight of soot in the particle filter
is so great that it is creating a counter pressure. Deal with any faults that appear or replace the particle filter. Run
command SC036: Reinitialise programming and select After particle filter replacement.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other Vdiags:
Consult PR848 Number of regeneration failures. If this parameter is greater than 3, it is essential to
change the engine oil.
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-433V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035HIGH PRESSURE FUEL CIRCUIT FAULT FINDING
NOTESThis command is used to interpret the state of the high pressure fuel circuit (high
pressure pump, rail, injectors and high pressure supply pipes).
To run this command, select scenario SC035 on the diagnostic tool.
Procedure to be followed:
– select scenario SC035,
– follow the instructions then “confirm”,
– with the command in progress: do not operate on the vehicle,
– switch off the engine at the end of the test,
–the diagnostic tool displays the results,
– end of test.
Interpretation of correct results:
– If the results displayed are OK, the entire high pressure fuel circuit is in order. There is no need for any
operation.
STEP X
(X is the variable
from 1 to 4)Rail pressure Raise
timeRail pressure Dump
timeInterpretation of
results
STEP X OK OK No operation
STEP 5 OK No operation
EDC16CP33_V18_SC035 / EDC16CP33_V1C_SC035 / EDC16CP33_V54_SC035 / EDC16CP33_V20_SC035 / EDC16CP33_V58_SC035 /
EDC16CP33_V5C_SC035 / EDC16CP33_V24_SC035 / EDC16CP33_V04_SC035 / EDC16CP33_V08_SC035 / EDC16CP33_V44_SC035 /
EDC16CP33_V4C_SC035 / EDC16CP33_V34_SC035 / EDC16CP33_V38_SC035 / EDC16CP33_V74_SC035 / EDC16CP33_V28_SC035 /
EDC16CP33_V62_SC035 / EDC16CP33_V26_SC035 / EDC16CP33_V60_SC035
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-434V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035
CONTINUED 1
Interpretation of incorrect results:
– Is one of the value definitions for the various displayed stages is “TOO SLOW” or “TOO FAST”, see the
following table:
STEP X
(X is the variable
from 1 to 4)Rail pressure Raise
timeRail pressure Dump
timeInterpretation of
results
STEP X TOO SLOW TOO SLOW Check 1
STEP X TOO SLOW TOO FAST Check 2
STEP X TOO SLOW OK Check 3
STEP X OK TOO SLOW Check 4
STEP X OK TOO FAST Check 5
STEP 5 TOO FAST Check 5
Explanation of results interpretation:
Check 1:
–Apply Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit leaks.
–Apply Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 2:
–Apply Test 10.
–Apply ALP6.
– Apply the part of Test 3 concerning the fuel filter.
– Replace the high pressure pump.
– Check the injector return flow and the injectors.
– Check the rail pressure regulator by running command AC225 Rail pressure regulator.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.