air filter RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-487
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP9 PARTICLE FILTER WARNING LIGHT COMES ON TOO OFTEN
NOTESBefore dealing with this customer complaint, check that there are no faults except
DF312 Speed request, and the conformity (or otherwise) of the "parameters" and
"statuses" using the diagnostic tool. Deal with the other faults first.
If the customer complaint is not eliminated, perform the following checks.
Have the last 10 regeneration
attempts failed?Are all the regeneration failures
linked to engine cut-off?
See group parameter (ET706
Stored engine status no. 1 to
ET715 Stored engine status no.
10)
(e.g. ET706 STOPPED)Output 1 Is the distance of PR412 Distance of
last successful regeneration less
than all the parameters of group 2?
(PR794 to PR803 Stored
regeneration failure no.1 to no.10)
Is at least one status for group
1 = STATUS4?Check the exhaust pipe for leaks
or blockage. Repair if necessary.
Carry out an After-Sales
regeneration if not already
performed. To do this, see SC017
Particle filter regeneration in
Interpretation of commands.Output 2
YES
YES
NONO
YES
A
NO
B
EDC16CP33_V18_ALP09 / EDC16CP33_V1C_ALP09 / EDC16CP33_V54_ALP09 / EDC16CP33_V20_ALP09 / EDC16CP33_V58_ALP09 /
EDC16CP33_V5C_ALP09 / EDC16CP33_V24_ALP09 / EDC16CP33_V28_ALP09 / EDC16CP33_V62_ALP09 / EDC16CP33_V26_ALP09 /
EDC16CP33_V60_ALP09
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-490
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
IMA*: Individual injector correction
ALP9
CONTINUED 3
– Check the consistency between the IMA* codes entered and the codes engraved on the injector bodies.
– Check that the particle filter differential pressure sensor is correctly positioned and connected (see MR 395, 402,
405, 364 or 370 Mechanical, 19B Exhaust, Particle filter pressure sensor: Removal - Refitting),
– Check the exhaust pipe (see TEST1 Exhaust pipe check),
– Check the air inlet circuit (see TEST4 Turbocharged air inlet circuit check),
– Check the air flowmeter (see TEST5 Air flowmeter),
– Check the turbocharger (see TEST7 Variable geometry turbocharger check),
– Check the injectors (see TEST10 Poor injector operation),
– Check the cylinder compressions.
If the fault has not been located and the customer complaint is still present, contact the Techline.
YES
E
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-491
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
Analysis of output for ALP9.
ALP9
CONTINUED 4
ALP
output no.Output conditions for
ALP9Cause - type of drivingRegeneration
frequencyWhat to tell the
customer?
Output 1The last 10 regeneration
attempts have failed due to
the engine cutting out.Regeneration failures
caused by engine cut-off.No regeneration
frequency analysis.Explain to the customer
the need to wait until the
end of regeneration
(warning light goes out)
before switching off the
engine.
Output 2The last 10 regeneration
attempts have failed but
not because of the engine
cutting out.Unsuitable driving
conditions.No regeneration
frequency analysis.Explain again to the
customer the driving
criteria for when the
warning light comes on.
Output 3After successful
regenerations stored in the
memory, the warning light
did not come on. No
interval can be calculated.Since the last successful
stored regenerations, the
driving conditions have not
allowed the warning light to
come on.Should be normal Vehicle correct
Output 4The interval between a
successful regeneration
and the particle filter
warning light coming on is
correct (above the lowest
possible values). The
system does not have any
irregular components.Unfavourable driving
(urban zone, underspeed,
etc.)Normal Vehicle correct
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-493V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST1 Exhaust system check
Engine stopped: Check that the silencer outlet is
not blocked. Repair or replace the silencer, if
necessary.
Check the seal of the exhaust manifold on the
contact surface between the turbocharger and the
exhaust manifold.
Is the seal in order?Repair or replace the faulty part.
Loosen the catalytic converter on the turbocharger
side.
Place a wooden block between the two parts.
Start the vehicle and check if the engine runs
better.
Is the engine running normally?The exhaust system is not the cause of the fault;
repeat the engine fault finding (see Customer
complaints - Fault finding chart).
Retighten the catalytic converter.
Loosen or separate the particle filter on the
catalytic converter side. Place a wooden block
between the two parts if necessary.
Start the vehicle and check if the engine runs
better.
Is the engine running normally?Replace the catalytic converter.
NO
YES
NO
YES
NO
YES
A
EDC16CP33_V18_TEST1 / EDC16CP33_V1C_TEST1 / EDC16CP33_V54_TEST1 / EDC16CP33_V20_TEST1 / EDC16CP33_V58_TEST1 /
EDC16CP33_V5C_TEST1 / EDC16CP33_V24_TEST1 / EDC16CP33_V04_TEST1 / EDC16CP33_V08_TEST1 / EDC16CP33_V44_TEST1 /
EDC16CP33_V4C_TEST1 / EDC16CP33_V34_TEST1 / EDC16CP33_V38_TEST1 / EDC16CP33_V74_TEST1 / EDC16CP33_V28_TEST1 /
EDC16CP33_V62_TEST1 / EDC16CP33_V26_TEST1 / EDC16CP33_V60_TEST1
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-494V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST1
CONTINUED
Retighten the particle filter.
Loosen or uncouple the silencer on the side of the
particle filter (see MR 395, 402, 405, 364, 370,
Mechanical, 19B Exhaust, Parts and
consumables for repair).
Start the vehicle and check if the engine runs
better.
Is the engine running normally?Replace the particle filter (see MR 395, 402, 405,
364, 370, Mechanical, 19B, Exhaust, Particle
filter, Removal - Refitting).
Reinitialise the parameters after the particle filter
is replaced.
Run command SC036 Reinitialise
programming and select After particle filter
replacement.
Replace the silencer.
A
YES
NO
YES
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-497V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3 Low pressure circuit check
Check the fuel filter:
– Conformity of the fuel filter (correct part number and RENAULT filter).
– Positioning and degree of clogging of the filter cartridge.
– Positioning and condition of the seals.
– If there is metal swarf in the filter:
Replace the fuel filter, bleed the circuit and continue the fault finding procedure.
Supplying the injection system with fuel from an additional tank.
This operation aims to detect possible faults in the low pressure supply system of a vehicle by replacing it entirely
with an additional tank.
Mode:
– Disconnect the diesel fuel supply pipe at the fuel filter inlet and block it with a plug.
– Connect a pipe to the fuel filter inlet and insert the other end in a clean container with a capacity of approximately
5 litres.
– Disconnect the diesel fuel return pipe at the diesel temperature sensor (pump return and injector return join), and
block it using a plug.
– Connect a transparent pipe to the union of the diesel fuel temperature sensor, and insert the other end in the
container.
– Fill the container with clean diesel fuel.
– Start the engine and let the system drain itself of its air (there must not be any air bubbles in the return pipe).
Is the customer complaint still present?If the low pressure circuit is in order, reconnect the
various low pressure circuit pipes, and repeat the
fault finding chart procedure or the procedure for
the fault that referred you to this test.
Are the low pressure circuit connections in order
and in good condition?Carry out the necessary repairs.
YES
NO
NO
A
YES
EDC16CP33_V18_TEST3 / EDC16CP33_V1C_TEST3 / EDC16CP33_V54_TEST3 / EDC16CP33_V20_TEST3 / EDC16CP33_V58_TEST3 /
EDC16CP33_V5C_TEST3 / EDC16CP33_V24_TEST3 / EDC16CP33_V04_TEST3 / EDC16CP33_V08_TEST3 / EDC16CP33_V44_TEST3 /
EDC16CP33_V4C_TEST3 / EDC16CP33_V34_TEST3 / EDC16CP33_V38_TEST3 / EDC16CP33_V74_TEST3 / EDC16CP33_V28_TEST3 /
EDC16CP33_V62_TEST3 / EDC16CP33_V26_TEST3 / EDC16CP33_V60_TEST3
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-498V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3
CONTINUED
Check the condition and operation of the priming bulb. Perform repairs if necessary and continue the test.
Check the condition of all the low pressure diesel pipes from the tank to the injection pump (in particular no pinching
of pipes).
If the fault is still present with a low fuel level, check the consistency of the actual fuel level and that indicated on
the instrument panel.
The transfer pump is supplied via a Venturi pipe located underneath it.
Check that the opening of the venturi (6 mm to 8 mm in diameter) is not blocked by dirt contained in the fuel tank.
Check the priming of the low pressure diesel circuit.
Check that the fuel tank is correctly filled and that the fuel is correct (see Test 12 Diesel fuel conformity check).
If the diesel fuel is not correct:
– Replace the fuel (diesel fuel).
– Replace the fuel filter (diesel fuel).
– Bleed the low and high pressure fuel circuit (diesel fuel).
Low pressure circuit correct.
A
YES
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-499V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST4 Turbocharged air inlet circuit check
Engine stopped: Check the sealing (leak or air intake) of the low and high pressure air circuit (before/after
turbocharger).
Check the parts that are abnormally greasy of the circuit and reveal a lack of tightness.
Check:
– the condition and fitting of the ducts (foreign, clogged, not joined, kinked, broken, pierced, cut bodies, tightness
of the mounting bolts, etc.).
– the presence, condition and fitting of the seals.
– the present and tightening of the clamps.
– The fitting of the turbocharging pressure sensor.
– The pipes and the take-off point between the air duct and the turbocharging sensor.
Carry out the necessary repairs.
Check the air filter.
Check:
– That the inlet and outlet of the air filter unit is not blocked.
– the condition and the assembly of the air filter unit (disconnected, broken, pierced …).
– The cleanliness, the conformity and the non-distortion of the filter element.
– The air flowmeter: run Test 5 Air flowmeter.
Carry out the necessary repairs
Check:
– the condition of the damper valve,
– the tightening of the mounting bolts,
– cracks in the damper valve.
Carry out the necessary repairs.
A
EDC16CP33_V18_TEST4 / EDC16CP33_V1C_TEST4 / EDC16CP33_V54_TEST4 / EDC16CP33_V20_TEST4 / EDC16CP33_V58_TEST4 /
EDC16CP33_V5C_TEST4 / EDC16CP33_V24_TEST4 / EDC16CP33_V04_TEST4 / EDC16CP33_V08_TEST4 / EDC16CP33_V44_TEST4 /
EDC16CP33_V4C_TEST4 / EDC16CP33_V34_TEST4 / EDC16CP33_V38_TEST4 / EDC16CP33_V74_TEST4 / EDC16CP33_V28_TEST4 /
EDC16CP33_V62_TEST4 / EDC16CP33_V26_TEST4 / EDC16CP33_V60_TEST4
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-507V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST11 Temperature upstream of turbine too low
Perform a complete fault finding of the
injection computer using the diagnostic tool.
Are there any present or stored faults?Apply the procedure for dealing with the
associated faults.
Run Test 1 Exhaust system check
Is the exhaust pipe correct?
Repair then carry out another particle filter
regeneration.
Run command SC017 "Particle filter
regeneration" (see Interpretation of
commands).
If the second regeneration is successful, it is
essential to change the engine oil and replace
the oil filter.
If the second regeneration fails, contact the
Techline. Apply Test 4 Turbocharged air inlet circuit
check.
Is the inlet circuit in order?
Run Test 4 Air flowmeter
Is the air flow sensor correct?
Run Test 10 Poor injector operation
Are the injectors correct?
Contact the Techline.
YES
NO
NO
NONO
NO
NO
YES
YES
YES
YES
EDC16CP33_V18_TEST11 / EDC16CP33_V1C_TEST11 / EDC16CP33_V54_TEST11 / EDC16CP33_V20_TEST11 /
EDC16CP33_V58_TEST11 / EDC16CP33_V5C_TEST11 / EDC16CP33_V24_TEST11 / EDC16CP33_V28_TEST11 /
EDC16CP33_V62_TEST11 / EDC16CP33_V26_TEST11 / EDC16CP33_V60_TEST11
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-508V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST12 Diesel fuel conformity check
WARNING
During this operation, it is essential to:
– refrain from smoking or bringing incandescent objects close to the work area,
– guard against petrol splashes caused by the residual pressure in the pipes,
– wear safety goggles with side guards,
– wear leaktight gloves (Nitrile type).
IMPORTANT
– To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
– To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (example: PANDA part no. 77 11 224 995). Record
the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Remove 1 litre of fuel from the diesel fuel filter outlet (see MR395 (Laguna II ph2) or MR402 (Vel Satis ph2)
or MR405 (Espace IV ph2) or MR364 (Mégane II ph2) or MR370 (Scénic II ph2), Mechanical, 19C, Tank, Fuel
tank: Draining), using a pneumatic transfer pump (part no. 634-200) and place it in the 1300 ml plastic cup.
Cover the plastic cup with its cover and let it settle for approximately2 minutes.
Is the fuel cloudy or does it
separate into two parts?Presence of water in diesel fuel, the fuel is not compliant.
Drain the fuel circuit, including the tank (see MR395 (Laguna II
ph2) or MR402 (Vel Satis ph2) or MR405 (Espace IV ph2) or
MR364 (Mégane II ph2) or MR370 (Scénic II ph2), Mechanical,
19C, Tank, Fuel tank: Draining).
YES
A
NO
EDC16CP33_V18_TEST12 / EDC16CP33_V1C_TEST12 / EDC16CP33_V54_TEST12 / EDC16CP33_V20_TEST12 /
EDC16CP33_V58_TEST12 / EDC16CP33_V5C_TEST12 / EDC16CP33_V24_TEST12 / EDC16CP33_V04_TEST12 /
EDC16CP33_V08_TEST12 / EDC16CP33_V44_TEST12 / EDC16CP33_V4C_TEST12 / EDC16CP33_V34_TEST12 /
EDC16CP33_V38_TEST12 / EDC16CP33_V74_TEST12 / EDC16CP33_V28_TEST12 / EDC16CP33_V62_TEST12/
EDC16CP33_V26_TEST12 / EDC16CP33_V60_TEST12
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74