air filter RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Manual PDF

13B-348
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR042FILTERED TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the filtered turbocharging pressure in bar.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
PR042 corresponds to the average value of PR041 Turbocharging pressure.
EDC16CP33_V18_PR042 / EDC16CP33_V1C_PR042 / EDC16CP33_V54_PR042 / EDC16CP33_V20_PR042 / EDC16CP33_V58_PR042 /
EDC16CP33_V5C_PR042 / EDC16CP33_V24_PR042 / EDC16CP33_V04_PR042 / EDC16CP33_V08_PR042 / EDC16CP33_V44_PR042 /
EDC16CP33_V4C_PR042 / EDC16CP33_V34_PR042 / EDC16CP33_V38_PR042 / EDC16CP33_V74_PR042 / EDC16CP33_V28_PR042 /
EDC16CP33_V62_PR042 / EDC16CP33_V26_PR042 / EDC16CP33_V60_PR042
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-386V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR381PARTICLE FILTER DOWNSTREAM TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the particle filter downstream temperature in °C.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Indicates the particle filter downstream air temperature in °C.
PR381 ≈ PR382 Particle filter upstream temperature ≈ ± 200°C
In the event of a fault, consult the interpretation of faults DF309 Particle filter downstream temperature sensor
and DF310 Particle filter upstream temperature sensor.
EDC16CP33_V18_PR381 / EDC16CP33_V1C_PR381 / EDC16CP33_V54_PR381 / EDC16CP33_V20_PR381 / EDC16CP33_V58_PR381 /
EDC16CP33_V5C_PR381 / EDC16CP33_V24_PR381
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
54, 58, 5C
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-387V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR382PARTICLE FILTER UPSTREAM TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air temperature of the exhaust gas upstream of the particle
filter in °C.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the air temperature of the exhaust gas upstream of the particle filter must be:
PR382 ≈ 200°C
In the event of a fault, consult the interpretation of faults DF309 Particle filter downstream temperature sensor
and DF310 Particle filter upstream temperature sensor.
EDC16CP33_V18_PR382 / EDC16CP33_V1C_PR382 / EDC16CP33_V54_PR382 / EDC16CP33_V20_PR382 / EDC16CP33_V58_PR382 /
EDC16CP33_V5C_PR382 / EDC16CP33_V24_PR382 / EDC16CP33_V28_PR382 / EDC16CP33_V62_PR382 / EDC16CP33_V26_PR382 /
EDC16CP33_V60_PR382
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-388V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
diff.*: differential
PR383WEIGHT OF SOOT IN PARTICLE FILTER
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in the particle filter in g.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the weight of soot in the particle filter must be:
PR383 < 56 g.
If the weight is greater than 56 g:
For all Vdiags (except 18): carry out an After-Sales regeneration. Run command SC017 Particle filter
regeneration and follow the procedure (see Interpretation of commands).
For Vdiag 18:
Reprogram the computer in Vdiag 1C.
Then apply the procedure corresponding to Vdiag 1C.
In the event of a fault, refer to the interpretation of fault DF315 Particle filter diff* pressure sensor.
EDC16CP33_V18_PR383 / EDC16CP33_V1C_PR383 / EDC16CP33_V54_PR383 / EDC16CP33_V20_PR383 / EDC16CP33_V58_PR383 /
EDC16CP33_V5C_PR383 / EDC16CP33_V24_PR383 / EDC16CP33_V28_PR383 / EDC16CP33_V62_PR383 / EDC16CP33_V26_PR383 /
EDC16CP33_V60_PR383
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-390V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
REPL*: REPLACEMENT
PR391DISTANCE SINCE PARTICLE FILTER REPL*
PARAMETER
DEFINITIONThis parameter indicates the distance since the particle filter was last replaced in
miles (km).
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Indicates the mileage travelled since replacement of the particle filter.
EDC16CP33_V18_PR391 / EDC16CP33_V1C_PR391 / EDC16CP33_V54_PR391 / EDC16CP33_V20_PR391 / EDC16CP33_V58_PR391 /
EDC16CP33_V5C_PR391 / EDC16CP33_V24_PR391 / EDC16CP33_V28_PR391 / EDC16CP33_V62_PR391 / EDC16CP33_V26_PR391 /
EDC16CP33_V60_PR391
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-394V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
diff.*: differential
PR414PARTICLE FILTER DIFF* PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the particle filter differential pressure in mbar.
NOTESNone.
Conformity check: Engine stopped and ignition on
The value of the particle filter differential pressure must be between:
- 1 mbar < PR414 < 1 mbar
In the event of a fault, refer to the interpretation of fault DF315 Particle filter diff* pressure sensor.
Conformity check with the engine running and engine coolant temperature > 80°C
The value of the particle filter differential pressure must be between:
10 mbar < PR414 < 100 mbar
In the event of a fault, refer to the interpretation of fault DF315.
EDC16CP33_V18_PR414 / EDC16CP33_V1C_PR414 / EDC16CP33_V54_PR414 / EDC16CP33_V20_PR414 / EDC16CP33_V58_PR414 /
EDC16CP33_V5C_PR414 / EDC16CP33_V24_PR414 / EDC16CP33_V28_PR414 / EDC16CP33_V62_PR414 / EDC16CP33_V26_PR414 /
EDC16CP33_V60_PR414
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-405V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793
CONTINUED
These parameters are used so that the history of the last ten activations of the particle filter warning light are
known.
In Vdiag 18, 1C, 54:
Each parameter from PR784 to PR793 records the distance when the particle filter warning light comes on which
is associated with the appearance of DF312.
Each time the particle filter warning light comes on, the vehicle mileage is stored in the following parameter (PR+1).
When all ten parameters have a value other than zero, and the particle filter warning light comes on again, the
distance information for PR784 is cleared and replaced by the new value.
For other Vdiags:
Each parameter from PR784 DF312 record no. 1 to PR793 DF312 record no. 10 contains a record of the vehicle
mileage when the particle filter warning light comes on. The appearance of fault DF312 Speed request is
associated with each of these parameters.
PR784 to PR793 operate through successive copying (when the particle filter warning light comes on, the value of
PR784 is copied to PR785 DF312 record no. 2, the value of PR785 is copied to PR786 DF312 record no. 3 and
so on).
When there are more than ten records, the value of PR793 is deleted. The new mileage is allocated to PR784.
If none of the parameters between PR784 and PR793 is available in the sub-function, this means that no data has
been saved. The parameters appear in the sub-function when they have a value above zero.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-407V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803
CONTINUED
In Vdiag 18, 1C, 54:
Each of these parameters contains the vehicle mileage during a failed particle filter regeneration when driving.
Each parameter relates to an engine status. The statuses and parameters are recorded at the same time (for
example PR797 is associated with ET709 Stored engine status no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero and there is a regeneration failure when driving, the distance
information for PR794 is cleared and replaced by the new value.
For other Vdiags:
Every parameter between PR794 Stored regeneration failure no. 1 and PR803 Stored regeneration failure no.
10 contains the vehicle mileage at the time of a particle filter regeneration failure when driving. Each parameter
relates to an engine status. They are recorded simultaneously (for example PR797 is associated with ET709
Stored engine status no. 4).
PR794 to PR803 operate through successive copying (when there is a regeneration failure when driving, the value
of PR794 is copied to PR795 Stored regeneration failure no. 2, the value of PR795 is copied to PR796 Stored
regeneration failure no. 3 and so on).
When there are more than ten records, the value of PR803 is deleted. The new mileage is allocated to PR794.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-408V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825STORED REGENERATION START NO. 1
STORED REGENERATION START NO. 2
STORED REGENERATION START NO. 3
STORED REGENERATION START NO. 4
STORED REGENERATION START NO. 5
STORED REGENERATION START NO. 6
STORED REGENERATION START NO. 7
STORED REGENERATION START NO. 8
STORED REGENERATION START NO. 9
STORED REGENERATION START NO. 10
PARAMETER
DEFINITIONThese parameters are shown in miles (km).
NOTESSpecial notes:
These parameters should only be interpreted for ALP 9 Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
These parameters are used so that the history of the last ten illuminations of the particle filter warning light are
known.
EDC16CP33_V18_PR816 / EDC16CP33_V18_PR817 / EDC16CP33_V18_PR818 / EDC16CP33_V18_PR819 / EDC16CP33_V18_PR820 /
EDC16CP33_V18_PR821 / EDC16CP33_V18_PR822 / EDC16CP33_V18_PR823 / EDC16CP33_V18_PR824 / EDC16CP33_V18_PR825 /
EDC16CP33_V1C_PR816 / EDC16CP33_V1C_PR817 / EDC16CP33_V1C_PR818 / EDC16CP33_V1C_PR819 / EDC16CP33_V1C_PR820 /
EDC16CP33_V1C_PR821 / EDC16CP33_V1C_PR822 / EDC16CP33_V1C_PR823 / EDC16CP33_V1C_PR824 / EDC16CP33_V1C_PR825 /
EDC16CP33_V54_PR816 / EDC16CP33_V54_PR817 / EDC16CP33_V54_PR818 / EDC16CP33_V54_PR819 / EDC16CP33_V54_PR820 /
EDC16CP33_V54_PR821 / EDC16CP33_V54_PR822 / EDC16CP33_V54_PR823 / EDC16CP33_V54_PR824 / EDC16CP33_V54_PR825 /
EDC16CP33_V20_PR816 / EDC16CP33_V20_PR817 / EDC16CP33_V20_PR818 / EDC16CP33_V20_PR819 / EDC16CP33_V20_PR820 /
EDC16CP33_V20_PR821 / EDC16CP33_V20_PR822 / EDC16CP33_V20_PR823 / EDC16CP33_V20_PR824 / EDC16CP33_V20_PR825 /
EDC16CP33_V58_PR816 / EDC16CP33_V58_PR817 / EDC16CP33_V58_PR818 / EDC16CP33_V58_PR819 / EDC16CP33_V58_PR820 /
EDC16CP33_V58_PR821 / EDC16CP33_V58_PR822 / EDC16CP33_V58_PR823 / EDC16CP33_V58_PR824 / EDC16CP33_V58_PR825 /
EDC16CP33_V5C_PR816 / EDC16CP33_V5C_PR817 / EDC16CP33_V5C_PR818 / EDC16CP33_V5C_PR819 / EDC16CP33_V5C_PR820 /
EDC16CP33_V5C_PR821 / EDC16CP33_V5C_PR822 / EDC16CP33_V5C_PR823 / EDC16CP33_V5C_PR824 / EDC16CP33_V5C_PR825 /
EDC16CP33_V24_PR816 / EDC16CP33_V24_PR817 / EDC16CP33_V24_PR818 / EDC16CP33_V24_PR819 / EDC16CP33_V24_PR820 /
EDC16CP33_V24_PR821 / EDC16CP33_V24_PR822 / EDC16CP33_V24_PR823 / EDC16CP33_V24_PR824 / EDC16CP33_V24_PR825 /
EDC16CP33_V26_PR816 / EDC16CP33_V26_PR817 / EDC16CP33_V26_PR818 / EDC16CP33_V26_PR819 / EDC16CP33_V26_PR820 /
EDC16CP33_V26_PR821 / EDC16CP33_V26_PR822 / EDC16CP33_V26_PR823 / EDC16CP33_V26_PR824 / EDC16CP33_V26_PR825 /
EDC16CP33_V60_PR816 / EDC16CP33_V60_PR817 / EDC16CP33_V60_PR818 / EDC16CP33_V60_PR819 / EDC16CP33_V60_PR820 /
EDC16CP33_V60_PR821 / EDC16CP33_V60_PR822 / EDC16CP33_V60_PR823 / EDC16CP33_V60_PR824 / EDC16CP33_V60_PR825
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.