sensor RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-338
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR022EGR VALVE POSITION FEEDBACK LOOP DIFFERENCE
PARAMETER
DEFINITIONThis parameter indicates the percentage difference between the setpoint and the EGR
valve position.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on
This parameter indicates the percentage difference between the setpoint and the EGR valve position.
In the event of a fault, consult the interpretation of faults DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation.
Conformity check with the engine running and engine coolant temperature > 80°C
The PR022 value must be between:
- 5% < PR022 < + 5%.
In the event of a fault, refer to the interpretation of faults DF209 and DF647.
EDC16CP33_V18_PR022 / EDC16CP33_V1C_PR022 / EDC16CP33_V54_PR022 / EDC16CP33_V20_PR022 / EDC16CP33_V58_PR022 /
EDC16CP33_V5C_PR022 / EDC16CP33_V24_PR022 / EDC16CP33_V04_PR022 / EDC16CP33_V08_PR022 / EDC16CP33_V44_PR022 /
EDC16CP33_V4C_PR022 / EDC16CP33_V34_PR022 / EDC16CP33_V38_PR022 / EDC16CP33_V74_PR022 / EDC16CP33_V28_PR022 /
EDC16CP33_V62_PR022 / EDC16CP33_V26_PR022 / EDC16CP33_V60_PR022
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-339
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR023DIFFERENCE IN AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the difference between the inlet air flow and the air entering
the engine in mg/st.
NOTESNone.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, consult the interpretation of fault DF056 Air flow sensor circuit.
EDC16CP33_V04_PR023 / EDC16CP33_V08_PR023 / EDC16CP33_V44_PR023 / EDC16CP33_V4C_PR023 / EDC16CP33_V34_PR023 /
EDC16CP33_V38_PR023 / EDC16CP33_V74_PR023 / EDC16CP33_V26_PR023 / EDC16CP33_V28_PR023 / EDC16CP33_V60_PR023 /
EDC16CP33_V62_PR023
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 26, 28,
34, 38, 44, 4C, 60, 62, 74

13B-340
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR030ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position as a percentage.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power, etc.).
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
If no pressure is being applied to the pedal PR030 = 0%.
In the event of a fault, consult the interpretation of DF196 Pedal sensor circuit gang 1 or DF198 Pedal sensor
circuit gang 2.
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
–3LR between components 120 and 921,
–3LS between components 120 and 921,
–3LT between components 120 and 921,
–3LU between components 120 and 921,
–3LW between components 120 and 921,
–3LV between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33_V18_PR030 / EDC16CP33_V1C_PR030 / EDC16CP33_V54_PR030 / EDC16CP33_V20_PR030 / EDC16CP33_V58_PR030 /
EDC16CP33_V5C_PR030 / EDC16CP33_V24_PR030 / EDC16CP33_V04_PR030 / EDC16CP33_V08_PR030 / EDC16CP33_V44_PR030 /
EDC16CP33_V4C_PR030 / EDC16CP33_V34_PR030 / EDC16CP33_V38_PR030 / EDC16CP33_V74_PR030 / EDC16CP33_V28_PR030 /
EDC16CP33_V62_PR030 / EDC16CP33_V26_PR030 / EDC16CP33_V60_PR030
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-341
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR030
CONTINUED
The accelerator pedal sensor should be connected, the vehicle should have the ignition on and the engine
switched off:
– Check that the accelerator pedal value is:
PR030 = 0%: no load,
100% < PR030 < 120%: full load,
135% < PR030 < 145%: full load after pedal kickdown point.
If the value is not correct, replace the pedal sensor.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-342
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR035ATMOSPHERIC PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the atmospheric pressure in bar. The sensor is integrated in
the computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The atmospheric pressure value must be between:
0.80 bar < PR035 < 1.20 bar.
In the event of a fault, consult the interpretation of fault DF004 Turbocharging pressure sensor circuit and
DF200 Atmospheric pressure sensor.
EDC16CP33_V18_PR035 / EDC16CP33_V1C_PR035 / EDC16CP33_V54_PR035 / EDC16CP33_V20_PR035 / EDC16CP33_V58_PR035 /
EDC16CP33_V5C_PR035 / EDC16CP33_V24_PR035 / EDC16CP33_V04_PR035 / EDC16CP33_V08_PR035 / EDC16CP33_V44_PR035 /
EDC16CP33_V4C_PR035 / EDC16CP33_V34_PR035 / EDC16CP33_V38_PR035 / EDC16CP33_V74_PR035 / EDC16CP33_V28_PR035 /
EDC16CP33_V62_PR035 / EDC16CP33_V26_PR035 / EDC16CP33_V60_PR035
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-344
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR038RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling etc.),
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on
The rail pressure value is between:
0 bar < PR038 < 90 bar if the coolant temperature < 30°C.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
The rail pressure value must be between:
250 bar < PR038 < 290 bar (at idle speed),
1680 bar < PR038 < 1720 bar (full load).
In the event of a fault, refer to the interpretation of fault DF007.
EDC16CP33_V18_PR038 / EDC16CP33_V1C_PR038 / EDC16CP33_V54_PR038 / EDC16CP33_V20_PR038 / EDC16CP33_V58_PR038 /
EDC16CP33_V5C_PR038 / EDC16CP33_V24_PR038 / EDC16CP33_V04_PR038 / EDC16CP33_V08_PR038 / EDC16CP33_V44_PR038 /
EDC16CP33_V4C_PR038 / EDC16CP33_V34_PR038 / EDC16CP33_V38_PR038 / EDC16CP33_V74_PR038 / EDC16CP33_V38_PR028 /
EDC16CP33_V62_PR038 / EDC16CP33_V26_PR038 / EDC16CP33_V60_PR038
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-345
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR038
CONTINUED
Sensor electrical conformity
Check the condition of the rail pressure sensor connector (see Wiring Diagram Technical Note, Vehicle,
Component code 1032).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, Component code 120).
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and absence of interference resistance of the following connections:
•3LX between components 120 and 1032,
•3LY between components 120 and 1032,
•3LZ between components 120 and 1032.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that there are no external diesel leaks from the high pressure fuel circuit.
With the ignition on and the engine stopped for over 1 minute:
View parameter PR038 Rail pressure.
– If the pressure is below 90 bar, the sensor is in order.
– If the pressure is above 90 bar, contact the Techline.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-346
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR041TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure in bar.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The turbocharging pressure value must be:
PR041 = PR035 Atmospheric pressure + /- 0.20 bar.
In the event of a fault, consult the interpretation of DF004 Turbocharging pressure sensor circuit.
EDC16CP33_V18_PR041 / EDC16CP33_V1C_PR041 / EDC16CP33_V54_PR041 / EDC16CP33_V20_PR041 / EDC16CP33_V58_PR041 /
EDC16CP33_V5C_PR041 / EDC16CP33_V24_PR041 / EDC16CP33_V04_PR041 / EDC16CP33_V08_PR041 / EDC16CP33_V44_PR041 /
EDC16CP33_V4C_PR041 / EDC16CP33_V34_PR041 / EDC16CP33_V38_PR041 / EDC16CP33_V74_PR041 / EDC16CP33_V28_PR041 /
EDC16CP33_V62_PR041 / EDC16CP33_V26_PR041 / EDC16CP33_V60_PR041
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-347
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR041
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3LQ between components 120 and 1071,
•3LP between components 120 and 1071,
•3LN between components 120 and 1071.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Vehicle with the ignition on, and the engine stopped for at least 1 minute:
Compare the values of PR041 Turbocharging pressure and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 is greater than 0.1 bar,
check the value of PR035 by comparing it with the reading on a vehicle in the workshop which is correct.
If the value of PR035 is not correct (difference greater than 0.1 bar between the 2 vehicles), contact the Techline.
Otherwise (when the value of PR035 is correct), replace the turbocharger pressure sensor.
If the difference between PR041 and PR035 is less than 0.1 bar.
Start the engine, with the engine idling:
Compare the values of PR041 and PR035.
If the difference between PR041 and PR035 is greater than 0.2 bar.
Check the air inlet circuit:
Apply Test 4 Turbocharged air inlet circuit check.
Low and high pressure air circuit sealed and not obstructed: ducts, mounting clamps present and tightened,
turbocharging pressure sensor fitted, exchanger, etc.
Check that the damper valve is not jammed closed.
Repair if necessary.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-349
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
OCR*: Opening Cyclic Ratio
PR048RAIL PRESSURE REGULATION VALVE OCR*
PARAMETER
DEFINITIONThis parameter indicates the turbocharger pressure opening cyclic ratio in %.
NOTESNone.
Conformity check: Engine stopped and ignition on
The turbo pressure opening cyclic ratio value must be:
PR048 = 15%
In the event of a fault, consult the interpretation of faults DF007 Rail pressure sensor circuit and DF053 Rail
pressure regulation function.
Conformity check: Engine running, engine coolant temperature > 80°C, without electrical consumers
The turbo pressure opening cyclic ratio value must be between:
35% < PR048 < 45%
In the event of a fault, refer to the interpretation of fault DF007.
EDC16CP33_V18_PR048 / EDC16CP33_V1C_PR048 / EDC16CP33_V54_PR048 / EDC16CP33_V20_PR048 / EDC16CP33_V58_PR048 /
EDC16CP33_V5C_PR048 / EDC16CP33_V24_PR048 / EDC16CP33_V04_PR048 / EDC16CP33_V08_PR048 / EDC16CP33_V44_PR048 /
EDC16CP33_V4C_PR048 / EDC16CP33_V34_PR048 / EDC16CP33_V38_PR048 / EDC16CP33_V74_PR048 / EDC16CP33_V28_PR048 /
EDC16CP33_V62_PR048 / EDC16CP33_V26_PR048 / EDC16CP33_V60_PR048
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74