exhaust RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 User Guide

13B-192
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF308
CONTINUED
1.DEFNOTESNone.
The fault appears if the weight of soot contained in the particle filter is:
– Vdiag 18 and 54: above 56 g.
– Vdiag 1C, 20, 24, 5C, 58: above 58 g
– Vdiag 26 and 28: greater than 68 g.
If Vdiag 18, reprogram the computer (see Replacement of components). Then apply the procedure
corresponding to the new Vdiag.
For the other Vdiag:
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
Clear fault DF308 Present or Stored.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-198
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
diff.*: Differential
temp.*: Temperature
DF311
CONTINUED
The fault appears following:
–7 failed regenerations when driving for Laguna II ph2.
–Between 9 and 11 failed regenerations when driving for Mégane II ph2, Vel Satis ph2 and Espace IV ph2.
If Vdiag 18, reprogram the computer (see Replacement of components). Then apply the procedure
corresponding to the new Vdiag.
For the other Vdiag:
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
Explain the regeneration procedure when driving to the customer to avoid unnecessary repairs: see SECTION D
in the interpretation of DF312 Speed request.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-203
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
13B
DF312
CONTINUED 4
PART B
1. No particle filter regeneration.
2.Write on the repair order the parameter and status relating to the last failure:
– Mileage of the last DF312 Speed request.
– Mileage of the last failures.
– Engine statuses of the last failures.
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3. Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the particle filter warning light or message came on (appeared at the Mileage of the last
DF312), the customer had not respected the driving recommendations: the failure that occurred at the Mileage of
the last failure is due to the engine being switched off.
4. Explain to the customer the procedure to turn off the warning light, making use of the parameters noted in the
repair order: see PART D.
PART C
If Vdiag 18:
Reprogram the computer in Vdiag 1C.
Then apply the procedure corresponding to Vdiag 1C.
If Vdiag 1C, 54, 58, 20 and 24:
– Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
– Carry out an After-Sales regeneration with approval from the Techline.
– Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
– Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D.
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-204
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 5
PART D
Procedure to switch off the Particle filter message or warning light on the instrument panel
Certain types of driving can trigger illumination of the particle filter warning light or message, and activate fault
DF312. The customer must carry out a specific driving operation (cf. vehicle user manual) that consists of:
1. When the engine is warm, drive at a speed greater than 48 mph (80 km/h) for 2 minutes to trigger the
regeneration procedure.
2.Keep driving at an average speed of 48 mph (80 km/h), until the "particle filter" warning light or message on
the instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without stopping
the engine or leaving the engine running at idle speed for an extended period of time. The regeneration time
depends on the vehicle and driving conditions but should last for 20 minutes maximum.
If regeneration fails when driving (the warning light does not go out or the service warning light comes on), check
the exhaust pipe for leaks or blockage. Repair if necessary. Proceed with an After Sales regeneration. Run
command SC017 (see Interpretation of commands).
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-227
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF647
CONTINUED 1
1.DEF
2.DEFNOTESNone.
Check the condition of the EGR valve (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2,
Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1460 or 169).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3EL and 3JM of component 1460 or 169.
If the resistance of the EGR valve is not between 1 kΩ < X < 7,5 kΩ, replace the EGR valve.
Measure the resistance between connections 3EL and 3GC of component 1460 or 169.
If the resistance of the EGR valve is not between 3.9 kΩ < X < 12.6 kΩ, replace the EGR valve.
After replacement, run command SC036 Reinitialise programming and select EGR valve to reinitialise the EGR
valve offsets.
Check the continuity and absence of interference resistance of the following connections:
•3GC between components 120 and 1460 or 169,
•3EL between components 120 and 1460 or 169,
•3JM between components 120 and 1460 or 169.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Remove and clean the EGR valve, then refit the EGR valve and start the engine (see MR364 (Mégane II ph2),
MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 14A,
Emission control, Exhaust gas recirculation solenoid valve: Removal - Refitting).
If the fault is still present, replace the EGR valve then run command SC036 Reinitialise programming and select
EGR valve to reinitialise the EGR valve offsets.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-228
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF647
CONTINUED 2
3.DEF
4.DEFNOTESNone.
Remove and clean the EGR valve, then refit it and start the engine. (see MR364 (Mégane II ph2), MR370 (Scénic
II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 14A, Emission control,
Exhaust gas recirculation valve: Removal - Refitting).
If the fault is still present, replace the EGR valve then run command SC036 and select EGR valve to reinitialise
the EGR valve offsets.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-234
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF717
PRESENT
OR
STOREDPARTICLE FILTER UPSTREAM PRESSURE
1.DEF: Inconsistency
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
–the level 1 warning light is lit,
– the EOBD (European On Board Diagnostic) warning light will come on after three
consecutive driving cycles (starting + 5 seconds + switching off the ignition and
waiting for 1 minute),
– the particle filter fault finding procedure is inhibited,
– particle filter regeneration is inhibited.
Check the condition of the pressure pipe between the particle filter upstream take-off point and the differential
pressure sensor.
Check that the pipe is not crushed, blocked or pierced.
Check that the differential pressure sensor is correctly positioned and connected (see MR 395, 402, 405, 364, 370,
Mechanical, 19B Exhaust, Particle filter pressure sensor: Removal - Refitting).
Replace the pressure pipe if necessary.
EDC16CP33_V18_DF717 / EDC16CP33_V1C_DF717 / EDC16CP33_V54_DF717 / EDC16CP33_V20_DF717 / EDC16CP33_V58_DF717 /
EDC16CP33_V5C_DF717 / EDC16CP33_V24_DF717 / EDC16CP33_V28_DF717 / EDC16CP33_V62_DF717 / EDC16CP33_V26_DF717 /
EDC16CP33_V60_DF717
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-262V12 MR-372-J84-13B300$090.mif
13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET007Pre-postheating control
ET024Thermoplunger no. 1 request
ET025Thermoplunger no. 2 request
ET026Thermoplunger no. 3 request
ET034Clutch signal registered
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET104Injector code use
ET120Pre-postheating signal
ET143Low-speed fan assembly relay control
ET144High-speed fan assembly relay control
ET205Thermoplunger no. 1 relay control (only on Laguna II ph2 without particle filter)
ET206Thermoplunger no. 2 relay control (only on Laguna II ph2 without particle filter)
ET207Thermoplunger no. 3 relay control (only on Laguna II ph2 without particle filter)
ET238Synchronisation
ET285Injection -> automatic gearbox connection
ET341Immobiliser code programmed
ET405Clutch pedal switch (only for manual gearboxes)
ET415Cruise control/Speed limiter deactivation
ET587Cooling of recirculated exhaust gas
ET589Electric coolant pump control (turbocharger)
ET615Automatic gearbox lever position
ET651EGR programming cut-off
DIESEL INJECTION
Fault finding – Status summary table

13B-263V12 MR-372-J84-13B300$090.mif
DIESEL INJECTION
Fault finding – Status summary table13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
*rege.: regeneration
*cool.: coolingTool status Diagnostic tool title
ET703Cruise control/speed limiter buttons
ET704Brakecontact No. 1
ET705Brakecontact No. 2
ET706Stored engine status no. 1
ET707Stored engine status no. 2
ET708Stored engine status no. 3
ET709Stored engine status no. 4
ET710Stored engine status no. 5
ET711Stored engine status no. 6
ET712Stored engine status no. 7
ET713Stored engine status no. 8
ET714Stored engine status no. 9
ET715Stored engine status no. 10
ET742Stored rege.* request status No.1
ET743Stored rege.* request status No.2
ET744Stored rege.* request status No.3
ET745Stored rege.* request status No.4
ET746Stored rege.* request status No.5
ET747Stored rege.* request status No.6
ET748Stored rege.* request status No.7
ET749Stored rege.* request status No.8
ET750Stored rege.* request status No.9
ET751Stored rege.* request status No.10
ET776Recirculated exhaust gas cool.* setpoint
ET781Heater plugs

13B-305V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET587RECIRCULATED EXHAUST GAS COOLING
STATUS
DEFINITIONACTIVE: This status indicates that exhaust gas cooling is recirculated.
INACTIVE: This status indicates that exhaust gas cooling is not recirculated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE:
According to computer programming.
In the event of a fault, consult the interpretation of faults
DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation
.
EDC16CP33_V18_ET587 / EDC16CP33_V1C_ET587 / EDC16CP33_V54_ET587 / EDC16CP33_V20_ET587 / EDC16CP33_V58_ET587 /
EDC16CP33_V5C_ET587 / EDC16CP33_V24_ET587 / EDC16CP33_V04_ET587 / EDC16CP33_V08_ET587 / EDC16CP33_V44_ET587 /
EDC16CP33_V4C_ET587 / EDC16CP33_V34_ET587 / EDC16CP33_V38_ET587 / EDC16CP33_V74_ET587 / EDC16CP33_V28_ET587 /
EDC16CP33_V62_ET587 / EDC16CP33_V26_ET587 / EDC16CP33_V60_ET587
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74