wiring RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-350
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR051EGR VALVE POSITION FEEDBACK
PARAMETER
DEFINITIONThis parameter indicates the opening ratio of the EGR valve in %.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (loss of power, smoke etc.).
– after interpretation of command AC103 EGR by-pass.
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, see the interpretation of faults DF209 EGR valve position sensor circuit and DF647 EGR
valve position regulation.
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3JM between components 120 and 1460 or 169,
•3EL between components 120 and 1460 or 169,
•3GC between components 120 and 1460 or 169.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16CP33_V18_PR051 / EDC16CP33_V1C_PR051 / EDC16CP33_V54_PR051 / EDC16CP33_V20_PR051 / EDC16CP33_V58_PR051 /
EDC16CP33_V5C_PR051 / EDC16CP33_V24_PR051 / EDC16CP33_V04_PR051 / EDC16CP33_V08_PR051 / EDC16CP33_V44_PR051 /
EDC16CP33_V4C_PR051 / EDC16CP33_V34_PR051 / EDC16CP33_V38_PR051 / EDC16CP33_V74_PR051 / EDC16CP33_V28_PR051 /
EDC16CP33_V62_PR051 / EDC16CP33_V26_PR051 / EDC16CP33_V60_PR051
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-353
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR059INLET AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air inlet temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on
With the ignition on the inlet air temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF002 Air temperature sensor circuit.
Parameter PR059 ≈ PR064 Coolant temperature engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the inlet air temperature varies according to the engine coolant temperature.
In the event of a fault, refer to the interpretation of fault DF002.
EDC16CP33_V18_PR059 / EDC16CP33_V1C_PR059 / EDC16CP33_V54_PR059 / EDC16CP33_V20_PR059 / EDC16CP33_V58_PR059 /
EDC16CP33_V5C_PR059 / EDC16CP33_V24_PR059 / EDC16CP33_V04_PR059 / EDC16CP33_V08_PR059 / EDC16CP33_V44_PR059 /
EDC16CP33_V4C_PR059 / EDC16CP33_V34_PR059 / EDC16CP33_V38_PR059 / EDC16CP33_V74_PR059 / EDC16CP33_V28_PR059 /
EDC16CP33_V62_PR059 / EDC16CP33_V26_PR059 / EDC16CP33_V60_PR059
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-354
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR059
CONTINUED
Sensor electrical conformity
With the flow sensor disconnected, check the insulation from earth of the following connection:
•3ABQ between components 120 and 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3ABQ and 3DW of component 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the resistances of the air flowmeter are not between:
8716 Ω < X < 9689 Ω (at - 10°C),
2353 Ω < X < 2544 Ω (at + 20°C),
794 Ω < X < 839 Ω (at + 50°C),
310 Ω < X < 321 Ω (at + 80°C),5497 Ω < X < Ω 6050 (at + 0°C),
1613 Ω < X < Ω 1730 (at + 30°C),
569 Ω < X < Ω 598 (at + 60°C),
234 Ω < X < Ω 242 (at + 90°C),3553 Ω < X < Ω 3875 (at +10°C),
1114 Ω < X < Ω 1186 (at +40°C),
418 Ω < X < Ω
436 (at +70°C),
replace the air flowmeter
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-356
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR063FUEL TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the fuel temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The fuel temperature value must be between:
– 30°C < PR063 <90°C
PR063 = 100°C (default value).
In the event of a fault, consult the interpretation of fault DF098 Fuel temperature sensor circuit.
EDC16CP33_V18_PR063 / EDC16CP33_V1C_PR063 / EDC16CP33_V54_PR063 / EDC16CP33_V20_PR063 / EDC16CP33_V58_PR063 /
EDC16CP33_V5C_PR063 / EDC16CP33_V24_PR063 / EDC16CP33_V04_PR063 / EDC16CP33_V08_PR063 / EDC16CP33_V44_PR063 /
EDC16CP33_V4C_PR063 / EDC16CP33_V34_PR063 / EDC16CP33_V38_PR063 / EDC16CP33_V74_PR063 / EDC16CP33_V28_PR063 /
EDC16CP33_V62_PR063 / EDC16CP33_V26_PR063 / EDC16CP33_V60_PR063
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-357
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR063
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3FAB between components 120 and 1066,
•3LD between components 120 and 1066.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3FAB and 3LD of component 1066.
If the fuel temperature sensor resistances are not between:
3538 Ω < X < 4502 Ω (at + 10°C),
1950 Ω < X < 2150 Ω (at + 25°C),
763 Ω < X < 857 Ω (at +50°C),
replace the sensor.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-358
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR064COOLANT TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check with engine stopped and ignition on.
With the ignition on the coolant temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF001 Coolant temperature sensor circuit.
Parameter PR059: Inlet air temperature ≈ PR064 engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the coolant temperature varies according to the engine temperature.
If there is a fault, refer to the interpretation of fault DF001.
EDC16CP33_V18_PR064 / EDC16CP33_V1C_PR064 / EDC16CP33_V54_PR064 / EDC16CP33_V20_PR064 / EDC16CP33_V58_PR064 /
EDC16CP33_V5C_PR064 / EDC16CP33_V24_PR064 / EDC16CP33_V04_PR064 / EDC16CP33_V08_PR064 / EDC16CP33_V44_PR064 /
EDC16CP33_V4C_PR064 / EDC16CP33_V34_PR064 / EDC16CP33_V38_PR064 / EDC16CP33_V74_PR064 / EDC16CP33_V28_PR064 /
EDC16CP33_V62_PR064 / EDC16CP33_V26_PR064 / EDC16CP33_V60_PR064
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-359
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR064
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3C between components 120 and 244,
•3JK between components 120 and 244,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3C and 3JK of component 244.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the temperature sensor resistances are not between:
11332 Ω < X < 13588 Ω (at - 10°C),
2140 Ω < X < 2364 Ω (at + 25°C),
772 Ω < X < 850 Ω (at + 50°C),
275 Ω < X < 291 Ω (at + 80°C),
112 Ω < X < 118 Ω (at + 110°C),
replace the sensor.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-374V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in kg/h.
NOTESThere must be no faults present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check with engine stopped and ignition on.
The inlet air flow value must be:
PR132 = 0 kg/h.
Conformity check with the engine running and engine coolant temperature > 80°C
The inlet air flow value must be between:
20 kg/h < PR132 < 30 kg/h.
EDC16CP33_V18_PR132 / EDC16CP33_V1C_PR132 / EDC16CP33_V54_PR132 / EDC16CP33_V20_PR132 / EDC16CP33_V58_PR132 /
EDC16CP33_V5C_PR132 / EDC16CP33_V24_PR132 / EDC16CP33_V04_PR132 / EDC16CP33_V08_PR132 / EDC16CP33_V44_PR132 /
EDC16CP33_V4C_PR132 / EDC16CP33_V34_PR132 / EDC16CP33_V38_PR132 / EDC16CP33_V74_PR132 / EDC16CP33_V28_PR132 /
EDC16CP33_V62_PR132 / EDC16CP33_V26_PR132 / EDC16CP33_V60_PR132
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-439V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC004TURBOCHARGING SOLENOID VALVE
NOTESPerform this fault finding procedure:
– following interpretation of an unresolved fault or,
– following application of the interpretation of PR041 Turbocharging pressure or
– after a customer complaint (loss of power, smoke etc.).
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
1. The following procedure is for checking that the turbocharger and its control circuit are working
properly.
Preliminary operation
Check the high pressure air circuit is sealed:
Apply Test 4 Turbocharged air inlet circuit check or Test 3 Low pressure circuit check.
Pipe not joined or pierced, pressure sensor disconnected or poorly fitted (seal present), exchanger pierced.
To test the exchanger: stabilise the engine speed between 3500 and 4000 rpm with the vehicle stopped and
check that there are no leaks.
Measure the resistance between connections3FB and 3MG of component1475.
If the resistance is not between 18 Ω and 22 Ω at + 23°C, replace the turbocharging solenoid valve.
Check the continuity of the following connection:
•3MG between the components 120 and 1475.
Check the + 12 V after relay supply of the turbocharging solenoid valve on the following connection:
•3FB of component 1475.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33_V18_AC004 / EDC16CP33_V1C_AC004 / EDC16CP33_V54_AC004 / EDC16CP33_V20_AC004 / EDC16CP33_V58_AC004 /
EDC16CP33_V5C_AC004 / EDC16CP33_V24_AC004 / EDC16CP33_V04_AC004 / EDC16CP33_V08_AC004 / EDC16CP33_V44_AC004 /
EDC16CP33_V4C_AC004 / EDC16CP33_V34_AC004 / EDC16CP33_V38_AC004 / EDC16CP33_V74_AC004 / EDC16CP33_V28_AC004 /
EDC16CP33_V62_AC004 / EDC16CP33_V26_AC004 / EDC16CP33_V60_AC004
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.