cruise control RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Service Manual

13B-326V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic Ratio
SV*: Solenoid valveTool parameter Diagnostic tool title
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR082Fuel temperature sensor voltage
PR083Air temperature sensor voltage
PR084Coolant temperature sensor voltage
PR086Pedal potentiometer voltage gang 1
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
PR104Turbocharging SV* OCR* setpoint
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR157Fuel flow setpoint
PR171Air flow setpoint for EGR
PR190Engine idle speed setpoint.
PR209Turbocharging pressure loop difference
PR213Rail pressure loop difference
PR224Turbocharging pressure sensor voltage
PR225Air flow sensor voltage
PR290AC refrigerant pressure sensor voltage (Mégane II ph2/Scénic II ph2 only)
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter

13B-373V12 MR-372-J84-13B300$122.mif
13B
PR130CRUISE CONTROL SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the cruise control speed setpoint in mph (km/h).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no faults present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The cruise control speed setpoint closure value must be:
PR130 > 18 mph (30 km/h).
Cruise control can only be activated for a speed.
EDC16CP33_V18_PR130 / EDC16CP33_V1C_PR130 / EDC16CP33_V54_PR130 / EDC16CP33_V20_PR130 / EDC16CP33_V58_PR130 /
EDC16CP33_V5C_PR130 / EDC16CP33_V24_PR130 / EDC16CP33_V04_PR130 / EDC16CP33_V08_PR130 / EDC16CP33_V44_PR130 /
EDC16CP33_V4C_PR130 / EDC16CP33_V34_PR130 / EDC16CP33_V38_PR130 / EDC16CP33_V74_PR130 / EDC16CP33_V28_PR130 /
EDC16CP33_V62_PR130 / EDC16CP33_V26_PR130 / EDC16CP33_V60_PR130
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-437V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ005PROGRAMMING
NOTESSpecial notes:
this command enables you to reinitialise the entire computer configuration according to
the vehicle.
Command RZ005 reconfigures the computer.
If the computer does not have any configuration data, use command RZ005 to enter the vehicle options:
– air conditioning,
– Passenger compartment heating resistor,
– cruise control/speed limiter.
These options are detected by the computer even if command RZ005 is not used.
The computer is configured as soon as the one of the vehicle's optional system components is operated.
EDC16CP33_V18_RZ005 / EDC16CP33_V1C_RZ005 / EDC16CP33_V54_RZ005 / EDC16CP33_V20_RZ005 / EDC16CP33_V58_RZ005 /
EDC16CP33_V5C_RZ005 / EDC16CP33_V24_RZ005 / EDC16CP33_V04_RZ005 / EDC16CP33_V08_RZ005 / EDC16CP33_V44_RZ005 /
EDC16CP33_V4C_RZ005 / EDC16CP33_V34_RZ005 / EDC16CP33_V38_RZ005 / EDC16CP33_V74_RZ005 / EDC16CP33_V28_RZ005 /
EDC16CP33_V62_RZ005 / EDC16CP33_V26_RZ005 / EDC16CP33_V60_RZ005
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.