sensor RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Repair Manual

13B-157
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
CONTINUED 2
Check the insulation from + 12 V and + 5 V (computer feeds) of the following connection:
•3LW between components 120 and 921.
Check the continuity of the following connection:
•3LV between components 120 and 921.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
1.DEF
NOTESNone.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3LR and 3LT of component 921.
If the resistance of the pedal sensor gang 2 is less than 500 Ω or greater than 2 kΩ, replace the sensor.
Measure the resistance between connections 3LS and 3LT of component 921.
If the resistance of the pedal sensor gang 2 is less than 500 Ω or greater than 10 kΩ, replace the sensor.
Measure the resistance between connections 3LV and 3LU of component 921.
If the resistance of the pedal sensor gang 2 is less than 500 Ω or greater than 3 kΩ, replace the sensor.
Measure the resistance between connections 3LV and 3LW of component 921.
If the resistance of the pedal sensor gang 2 is less than 500 Ω or greater than 10 kΩ, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-158
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
CONTINUED 3
Check for continuity and absence of interference resistance on the following connections:
•3LR between components 120 and 921,
•3LS between components 120 and 921,
•3LT between components 120 and 921,
•3LU between components 120 and 921,
•3LW between components 120 and 921,
•3LV between components 120 and 921.
Check the insulation between the following connections:
•3LW between components 120 and 921,
•3LS between components 120 and 921.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, vary the pedal position and refer to the interpretation of PR030 Accelerator pedal
position to check the operating values of the accelerator pedal sensor.
If the values displayed are inconsistent, replace the accelerator pedal sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-159
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF200
PRESENT
OR
STOREDATMOSPHERIC PRESSURE SENSOR
1.DEF: Above maximum threshold
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– the engine is started,
– a road test.
Special notes:
The EOBD (European On Board Diagnostic) warning light is lit.
The atmospheric pressure sensor is integrated in the injection computer, and cannot be
separated.
If the fault is present:
– there is light smoke,
– the atmospheric pressure value changes to safe mode, PR035 Atmospheric
pressure = 0.75 bar.
Use bornier Elé. 1681 for any work on the computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Disconnect the injection computer and check the condition of the engine management computer connector (see

Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2,
component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the value of PR035 Atmospheric pressure by comparing it with the reading on a conforming vehicle in the
workshop
.
If the value of PR035 is not correct (difference greater than 0.1 bar between the 2 vehicles), contact the Techline.
EDC16CP33_V18_DF200 / EDC16CP33_V1C_DF200 / EDC16CP33_V54_DF200 / EDC16CP33_V20_DF200 / EDC16CP33_V58_DF200 /
EDC16CP33_V5C_DF200 / EDC16CP33_V24_DF200 / EDC16CP33_V04_DF200 / EDC16CP33_V08_DF200 / EDC16CP33_V44_DF200 /
EDC16CP33_V4C_DF200 / EDC16CP33_V34_DF200 / EDC16CP33_V38_DF200 / EDC16CP33_V74_DF200 / EDC16CP33_V28_DF200 /
EDC16CP33_V62_DF200 / EDC16CP33_V26_DF200 / EDC16CP33_V60_DF200
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-160
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF209
PRESENT
OR
STOREDEGR VALVE POSITION SENSOR CIRCUITCC.0: Short circuit to earth
CO.0: Open circuit or short circuit to earth
CO.1: Open circuit or short circuit to +12 V
1.DEF: Open circuit or short circuit
NOTESPriorities when dealing with a number of faults:
– DF046 Battery voltage.
– DF012 Sensor supply voltage no. 2.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– the engine is started,
– a road test.
Special notes:
If the fault is present:
–the EOBD (European On Board Diagnostic) warning light is lit,
– EGR programming cut-off: valve in the closed position,
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for all operations on the engine management computer
connector.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
CO.1
1.DEF
NOTESNone.
Check the condition of the EGR valve (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2,
Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1460 or 169).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF209 / EDC16CP33_V1C_DF209 / EDC16CP33_V54_DF209 / EDC16CP33_V20_DF209 / EDC16CP33_V58_DF209 /
EDC16CP33_V5C_DF209 / EDC16CP33_V24_DF209 / EDC16CP33_V04_DF209 / EDC16CP33_V08_DF209 / EDC16CP33_V44_DF209 /
EDC16CP33_V4C_DF209 / EDC16CP33_V34_DF209 / EDC16CP33_V38_DF209 / EDC16CP33_V74_DF209 / EDC16CP33_V28_DF209 /
EDC16CP33_V62_DF209 / EDC16CP33_V26_DF209 / EDC16CP33_V60_DF209
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-161
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF209
CONTINUED 1
Measure the resistance between connections 3GC and 3JM (sensor supply and sensor earth), and between
connections 3EL and 3JM (sensor signal and sensor earth) of component 1460 or 169.
If the resistances of the EGR valve are less than 1 kΩ, replace the valve.
After replacement, run command SC036 Reinitialise programming and select EGR VALVE to reinitialise the
EGR valve offsets.
Check the insulation from + 12 V and + 5 V (computer feeds) of the following connection:
•3EL between components 120 and 1460 or 169.
Check the continuity of the following connection:
•3JM between components 120 and 1460 or 169.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation between the following connections:
•3EL between components 120 and 1460 or 169,
•3VP between components 120 and 1460 or 169.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-162
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF209
CONTINUED 2
CO.0
CC.0NOTESNone.
Check the condition of the EGR valve (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2,
Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1460 or 169).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3GC and 3JM (sensor supply and sensor earth), and between
connections 3EL and 3JM (sensor signal and sensor earth) of component 1460 or 169.
If the resistances of the EGR valve are greater than 15 kΩ, replace the valve.
After replacement, run command SC036 Reinitialise programming and select EGR valve to reinitialise the EGR
valve offsets.
Check the continuity of the following connections:
•3EL between components 120 and 1460 or 169,
•3GC between components 120 and 1460 or 169.
Check the insulation to earth of the following connection:
•3EL between components 120 and 1460 or 169.
Check the insulation between the following connections:
•3EL between components 120 and 1460 or 169,
•3VQ between components 120 and 1460 or 169.
If the connection or connections are faulty and if there is a repair method (see
Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-163
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF221
STOREDCLUTCH CONTACT SIGNAL1.DEF: Clutch inconsistency upon gear change
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present during a road test at over 21 mph (35 km/h).
Special notes:
– the cruise control/speed limiter function is switched off.
Use bornier Elé. 1681 for all operations on the engine management computer
connector.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check the condition of the clutch sensor connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 675).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Display status ET405 Clutch pedal switch (can only be displayed for Manual Gearboxes) which is normally
INACTIVE when the pedal is not depressed.
Depress the clutch pedal and note whether this status becomes ACTIVE.
If the status becomes ACTIVE when the clutch pedal is in the rest position.
Clear the fault, switch off the ignition, wait for the end of the power-latch and wait for the diagnostic tool message
(maximum wait 8 min): Loss of dialogue with the computer: EDC16 CP33, check the tool connection and the
computer supply voltage and switch on the ignition again.
Carry out a road test and then take a fault reading.
If the fault is still present, contact the Techline.
EDC16CP33_V18_DF221M / EDC16CP33_V1C_DF221M / EDC16CP33_V54_DF221M / EDC16CP33_V20_DF221M /
EDC16CP33_V58_DF221M / EDC16CP33_V5C_DF221M / EDC16CP33_V24_DF221M / EDC16CP33_V04_DF221M /
EDC16CP33_V08_DF221M / EDC16CP33_V44_DF221M / EDC16CP33_V4C_DF221M / EDC16CP33_V34_DF221M /
EDC16CP33_V38_DF221M / EDC16CP33_V74_DF221M / EDC16CP33_V28_DF221M / EDC16CP33_V62_DF221M /
EDC16CP33_V26_DF221M / EDC16CP33_V60_DF221M
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-183
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
PRESENT
OR
STOREDWATER IN DIESEL FUEL SENSOR
1.DEF: Open circuit on the line or water present in the diesel fuel
NOTESIMPORTANT:
Please observe the cleanliness guidelines and safety advice.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check that there is no water in the fuel filter.
Bleed the fuel filter and the low pressure diesel circuit if necessary.
Start the engine and wait at least 1 minute to confirm the repair.
If the fault was stored but not present, carry out a road test (see Note).
If the fault is still present:
Check the continuity and absence of interference resistance on the following connection:
•3WT between the components 120 and 414.
Check the + 12 V after relay supply to the water detection sensor on the following connection:
•3FB of component 414.
Check that the earth is in order on connection NT or M of component 414.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Start the engine and wait at least 1 minute to confirm the repair.
If the fault is still present, check the conformity of the fuel used:
– Check that the fuel tank has been filled correctly.
–Run Test 12 Fuel conformity check.
– If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low pressure diesel circuit.
EDC16CP33_V18_DF293 / EDC16CP33_V1C_DF293 / EDC16CP33_V54_DF293 / EDC16CP33_V20_DF293 / EDC16CP33_V58_DF293 /
EDC16CP33_V5C_DF293 / EDC16CP33_V24_DF293 / EDC16CP33_V04_DF293 / EDC16CP33_V08_DF293 / EDC16CP33_V44_DF293 /
EDC16CP33_V4C_DF293 / EDC16CP33_V34_DF293 / EDC16CP33_V38_DF293 / EDC16CP33_V74_DF293 / EDC16CP33_V28_DF293 /
EDC16CP33_V62_DF293 / EDC16CP33_V26_DF293 / EDC16CP33_V60_DF293
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-184
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
CONTINUED
If none of these checks reveal any faults:
– Replace the water detection sensor.
– Clear the fault.
Start the engine and wait at least 1 minute to confirm the repair.
Note:
When the water level in the fuel filter unit is below the sensor's electrodes, some driving conditions (cornering,
gradients) may result in water being detected (in fact, the sensor's off-centre position in the fuel filter unit, combined
with the driving conditions, causes water to be detected).
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-185
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF297
PRESENT
OR
STOREDPRESSURE SENSOR
1. DEF: Absent
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– blue/white smoke and black particles coming from the exhaust,
– the EOBD (European On Board Diagnostic) warning light will come on after three
consecutive driving cycles (starting + 5 seconds + switch off the ignition and wait
40 seconds).
–The level 1 warning light is lit (for Vdiag 20, 24, 58, 5C, 26, 28, 60 and 62).
Priorities when dealing with a number of faults:
– DF315 Particle filter diff. pressure sensor if present or stored.
– DF717 Particle filter upstream pressure if it is present or stored.
NOTE:
In the long term, this fault may lead to premature wear and a greater risk of turbocharger
failure.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note, Laguna
II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF297 / EDC16CP33_V1C_DF297 / EDC16CP33_V54_DF297 / EDC16CP33_V20_DF297 / EDC16CP33_V58_DF297 /
EDC16CP33_V5C_DF297 / EDC16CP33_V24_DF297 / EDC16CP33_V28_DF297 / EDC16CP33_V62_DF297 / EDC16CP33_V26_DF297 /
EDC16CP33_V60_DF297
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62