relay RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Repair Manual

13B-267V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET007PRE-POSTHEATING UNIT CONTROL
STATUS
DEFINITIONACTIVE: when the heater plugs are activated according to the engine coolant
temperature.
INACTIVE: after the engine has been running for a certain period
In the event of a fault, consult the interpretation of fault DF017 Preheating unit
control circuit.
NOTESSpecial notes:
This status is specific to slow heater plugs (black ring).
Conformity check with engine stopped and ignition on.
"ACTIVE"When the ignition is switched on, status ET007 should be ACTIVE for a time that varies
according to the engine coolant temperature. Both the relay and the heater plugs are
supplied.
After starting, the status should remain ACTIVE for a time that varies according
to the engine temperature. This is the postheating phase.
If ET007 is INACTIVE when the ignition is switched on, check:
– Supply fuse FM12 (70A) of component 597 (engine fuse and relay box) or F2 (70A)
of component 777 for Mégane II and Scénic II
–The supply to the heater plugs after relay actuation, and the connections of the
heater plugs.
Important: on this engine, the plug supply voltage is variable.
– Check the continuity and absence of interference resistance of the following
connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
EDC16CP33_V18_ET007 / EDC16CP33_V1C_ET007 / EDC16CP33_V54_ET007 / EDC16CP33_V20_ET007 / EDC16CP33_V58_ET007 /
EDC16CP33_V5C_ET007 / EDC16CP33_V24_ET007 / EDC16CP33_V04_ET007 / EDC16CP33_V08_ET007 / EDC16CP33_V44_ET007 /
EDC16CP33_V4C_ET007 / EDC16CP33_V34_ET007 / EDC16CP33_V38_ET007 / EDC16CP33_V74_ET007 / EDC16CP33_V28_ET007 /
EDC16CP33_V26_ET007
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-269V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET024
ET025
ET026THERMOPLUNGER NO. 1 REQUESTTHERMOPLUNGER NO. 2 REQUEST
THERMOPLUNGER NO. 3 REQUEST
STATUS
DEFINITIONACTIVE: These statuses indicate that the thermoplungers are active.
INACTIVE: These statuses indicate that the thermoplungers are inactive.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"INACTIVE"Statuses ET024, ET025, and ET026 are INACTIVE when the ignition is switched on
with the engine stopped, or when the engine is warm.
"ACTIVE"Statuses ET024, ET025, and ET026 are ACTIVE when:
– the engine has been started,
– and the engine coolant temperature is low (< 15°C),
– and the air temperature is low (< 5°C).
This strategy allows the engine coolant to be heated and to allow the heating of the
passenger compartment.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Thermoplunger no. 1 relay,
– AC064 Thermoplunger no. 2 relay,
– AC031 Thermoplunger no. 3 relay.
In the event of a fault, refer to the interpretation of faults:
– DF032 Thermoplunger no. 1 relay control circuit,
– DF033 Thermoplunger no. 2 relay control circuit,
– DF034 Thermoplunger no. 3 relay control circuit.
EDC16CP33_V18_ET024 / EDC16CP33_V18_ET025 / EDC16CP33_V18_ET026 / EDC16CP33_V1C_ET024 / EDC16CP33_V1C_ET025 /
EDC16CP33_V1C_ET026 / EDC16CP33_V54_ET024 / EDC16CP33_V54_ET025 / EDC16CP33_V54_ET026 / EDC16CP33_V20_ET024 /
EDC16CP33_V20_ET025 / EDC16CP33_V20_ET026 / EDC16CP33_V58_ET024 / EDC16CP33_V58_ET025 / EDC16CP33_V58_ET026 /
EDC16CP33_V5C_ET024 / EDC16CP33_V5C_ET025 / EDC16CP33_V5C_ET026 / EDC16CP33_V24_ET024 / EDC16CP33_V24_ET025 /
EDC16CP33_V24_ET026 / EDC16CP33_V28_ET024 / EDC16CP33_V28_ET025 / EDC16CP33_V28_ET026 / EDC16CP33_V62_ET024 /
EDC16CP33_V62_ET025 / EDC16CP33_V62_ET026 / EDC16CP33_V26_ET024 / EDC16CP33_V60_ET024 / EDC16CP33_V26_ET025 /
EDC16CP33_V60_ET025 / EDC16CP33_V26_ET026 / EDC16CP33_V60_ET026
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-286V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143LOW-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS
DEFINITIONThis status indicates whether the low speed fan assembly is active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
If the vehicle is fitted with air conditioning, the fan assembly electrical circuit includes
2 relays. The 1
st speed fan assembly relay will be actuated when the engine coolant
temperature exceeds 99°C and its function is to cool the engine so that the engine
temperature does not exceed 102°C. If the engine coolant temperature exceeds 102°C,
the 2
nd speed fan assembly relay will be actuated and the fan will rotate faster.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
IMPORTANT:
If the vehicle is equipped with air conditioning, the engine cooling fan will operate at 1
st speed as soon as the air
conditioning compressor is activated.
Conformity check with engine stopped and ignition on.
"INACTIVE"Engine cold and air conditioning switched off
In the event of a fault, consult the interpretation of fault DF018 Low speed fan
assembly control circuit.
EDC16CP33_V18_ET143 / EDC16CP33_V1C_ET143 / EDC16CP33_V54_ET143 / EDC16CP33_V20_ET143 / EDC16CP33_V58_ET143 /
EDC16CP33_V5C_ET143 / EDC16CP33_V24_ET143 / EDC16CP33_V04_ET143 / EDC16CP33_V08_ET143 / EDC16CP33_V44_ET143 /
EDC16CP33_V4C_ET143 / EDC16CP33_V34_ET143 / EDC16CP33_V38_ET143 / EDC16CP33_V74_ET143 / EDC16CP33_V28_ET143 /
EDC16CP33_V26_ET143
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-287V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143
CONTINUED 1
Conformity check with the engine running and engine coolant temperature > 80°C
INACTIVE or ACTIVE, depending on the engine temperature (air conditioning switched off).
In the event of a fault, refer to the interpretation of fault DF018.
Sensor electrical conformity
"ACTIVE"When the coolant reaches 99°C, the injection computer actuates the low-speed fan
assembly relay, and status ET143 becomes ACTIVE. The relay then supplies the
fan assembly and the cooling fan begins to turn.
If status ET143 is ACTIVE, but the cooling fan is not running, perform the following
operations:
Check the condition of fuse FM15 (60 A) in the engine fuse and relay box (see MR364
(Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis
ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of
components).
Disconnect the low speed and high speed relays, check that they are operating
correctly and check the condition of the relay mounting connectors (see Wiring
Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II
ph2, Scénic II ph2, component code 597).
If one of the connectors is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, wiring: precautions for repair), repair the
connector, otherwise replace the wiring.
Check the + 12 V after relay supply to the low speed fan assembly relay on the
following connection:
•3FB of component 700.
Check the continuity and absence of interference resistance of the following
connections:
•49L between components 700 and 321,
•49B between components 262 and 321,
•3JN between components 700 and 120.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-288V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET143
CONTINUED 2
"ACTIVE"
Check that the earth is in order on connection MAS of component 262.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
"INACTIVE"If the engine temperature is lower than 99°C, the engine cooling fan cannot switch
on and the low speed fan relay of the cannot be run.
Status ET143 should therefore be INACTIVE when the control relay and the engine
cooling fan are not supplied.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-289V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144HIGH-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS
DEFINITIONThis status indicates whether the high speed fan assembly is active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
If the vehicle is not fitted with air conditioning, low-speed fan assembly relay does not
exist. The circuit therefor only contains a single command relay to supply the engine
cooling fan. The engine cooling fan will thus have only one operating speed.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Conformity check with engine stopped and ignition on.
"INACTIVE"Engine cold and air conditioning switched off
In the event of a fault, consult the interpretation of fault DF019 High speed fan
assembly control circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
INACTIVE or ACTIVE, depending on the engine temperature (air conditioning switched off).
In the event of a fault, refer to the interpretation of fault DF019.
EDC16CP33_V18_ET144 / EDC16CP33_V1C_ET144 / EDC16CP33_V54_ET144 / EDC16CP33_V20_ET144 / EDC16CP33_V58_ET144 /
EDC16CP33_V5C_ET144 / EDC16CP33_V24_ET144 / EDC16CP33_V04_ET144 / EDC16CP33_V08_ET144 / EDC16CP33_V44_ET144 /
EDC16CP33_V4C_ET144 / EDC16CP33_V34_ET144 / EDC16CP33_V38_ET144 / EDC16CP33_V74_ET144 / EDC16CP33_V28_ET144 /
EDC16CP33_V26_ET144
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-290V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144
CONTINUED 1
Sensor electrical conformity
"ACTIVE"When the coolant reaches 102°C, the injection computer actuates the fan assembly
relay and status ET144 becomes ACTIVE. The relay then supplies the cooling fan.
If status ET144 is ACTIVE, but the cooling fan is not running, perform the following
operations:
Check the condition of fuse FM15 (60 A) in the engine fuse and relay box (see MR364
(Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis
ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List and location of
components).
Disconnect the low speed and high speed relays, check that they are operating
correctly and check the condition of the relay mounting connectors (see Wiring
Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II
ph2, Scénic II ph2, component code 597).
If one of the connectors is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, wiring: precautions for repair), repair the
connector, otherwise replace the wiring.
Check the + 12 V after relay supply to the high-speed fan assembly relay on the
following connection:
•3FB of component 234.
Check the continuity and absence of interference resistance of the following
connections:
•3JP between components 234 and 120,
•49B between components 234 and 262.
Check that the earth is in order on connection MAS of component 262.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74

13B-292V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
Only for Laguna II ph2 without a particle filter
ET205
ET206
ET207THERMOPLUNGER 1 RELAY CONTROLTHERMOPLUNGER 2 RELAY CONTROL
THERMOPLUNGER 3 RELAY CONTROL
STATUS
DEFINITIONACTIVE: This status indicates that the thermoplunger is supplied.
INACTIVE: This status indicates that the thermoplunger is not supplied.
NOTESNone.
"INACTIVE"Statuses ET205, ET206, ET207 are INACTIVE when the ignition is switched on
and the engine stopped, or when the engine is warm.
"ACTIVE"Statuses ET205, ET206 and ET207 are ACTIVE when the engine is started, the
engine coolant temperature is low (<15°C) and the air temperature is low (<5°).
This program allows the engine coolant to be heated to enable the passenger
compartment to be heated.
The thermoplungers also act both to load the engine to improve regeneration of
the particle filter.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Thermoplunger no.1 relay,
– AC064 Thermoplunger no. 2 relay,
– AC031 Thermoplunger no.3 relay.
In the event of a fault, refer to the interpretation of faults:
– DF034 "Thermoplunger 3 relay control circuit",
– DF033 "Heating element 2 relay control circuit",
– DF032 Thermoplunger 1 relay control circuit.
EDC16CP33_V04_ET205 / EDC16CP33_V04_ET206 / EDC16CP33_V04_ET207 / EDC16CP33_V08_ET205 / EDC16CP33_V08_ET206 /
EDC16CP33_V08_ET207 / EDC16CP33_V44_ET205 / EDC16CP33_V44_ET206 / EDC16CP33_V44_ET207 / EDC16CP33_V4C_ET205 /
EDC16CP33_V4C_ET206 / EDC16CP33_V4C_ET207 / EDC16CP33_V34_ET205 / EDC16CP33_V34_ET206 / EDC16CP33_V34_ET207 /
EDC16CP33_V38_ET205 / EDC16CP33_V38_ET206 / EDC16CP33_V38_ET207 / EDC16CP33_V74_ET205 / EDC16CP33_V74_ET206 /
EDC16CP33_V74_ET207
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 34, 38,
44, 4C, 74

13B-354
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR059
CONTINUED
Sensor electrical conformity
With the flow sensor disconnected, check the insulation from earth of the following connection:
•3ABQ between components 120 and 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3ABQ and 3DW of component 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the resistances of the air flowmeter are not between:
8716 Ω < X < 9689 Ω (at - 10°C),
2353 Ω < X < 2544 Ω (at + 20°C),
794 Ω < X < 839 Ω (at + 50°C),
310 Ω < X < 321 Ω (at + 80°C),5497 Ω < X < Ω 6050 (at + 0°C),
1613 Ω < X < Ω 1730 (at + 30°C),
569 Ω < X < Ω 598 (at + 60°C),
234 Ω < X < Ω 242 (at + 90°C),3553 Ω < X < Ω 3875 (at +10°C),
1114 Ω < X < Ω 1186 (at +40°C),
418 Ω < X < Ω
436 (at +70°C),
replace the air flowmeter
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.