oil temperature RENAULT SCENIC 2014 J95 / 3.G Petrol Injection - Sagem3000 Workshop Manual

PETROL INJECTION
Fault finding – System operation17B
17B - 7V12 MR-372-J84-17B000$090.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – System operation
1. SYSTEM OPERATION
Composition
The injection system consists of the:
– accelerator potentiometer,
– accelerator pedal switch,
– TDC sensor,
– atmospheric pressure sensor,
– air temperature sensor,
– coolant temperature sensor,
– freon pressure sensor,
– upstream oxygen sensor,
– downstream oxygen sensor,
– cruise control switch,
– steering column switch,
– cruise control on/off switch,
– brake lights switch,
– fuel vapour absorber,
– injection computer,
– motorised throttle valve,
– four injectors,
– four pencil coils,
– + turbocharging pressure sensor,
– coolant pump
– turbocharging solenoid valve.
Computer
SAGEM S3000 flash EEPROM 128-track computer controlling the injection and the ignition.
Multipoint injection in sequential mode.
Connections to the other computers:
– Protection and Switching Unit (UPC)
– Passenger Compartment Control Unit (UCH),
– Automatic Transmission Electronic Control Unit (AUTO ECU).
JSAA741.0
MR-372-J84-17B000$090.mif

PETROL INJECTION
Fault finding – Interpretation of faults17B
17B-45V12 MR-372-J84-17B000$315.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DF065
PRESENT
OR
STOREDCOMBUSTION MISFIRES
1.DEF : destructive misfiring
2.DEF : pollutant misfiring
NOTESPriority for dealing with a combination of faults:
– ignition: DF072, DF073, DF074 and DF075.
– fuel supply system: DF026, DF027, DF028, DF029 and DF085.
– engine flywheel signal: DF005 and DF125.
– cylinder misfires: DF059, DF060, DF061 and DF062.
Conditions for applying the fault finding procedure to stored faults:
The fault is considered present under the following conditions:
– there must be no further electrical faults,
– programming must be carried out.
– engine warm (min 75°C),
– idling with all the electrical consumers activated for 15 minutes.
Special note:
–OBD warning light illuminated.
Check the injectors.
Check the condition and conformity of the spark plugs.
Check the ignition pencil coils.
Check that the correct fuel is being used.
If the fault is still present, carry out the following checks:
– check the flywheel sensor,
– check the condition and cleanliness of the flywheel,
– check the flywheel sensor mounting,
– check the flywheel/sensor air gap
– check the cylinder compressions,
– check the complete fuel supply system (see Workshop Repair Manual 364 Mechanics, 13A, Fuel supply),
– check the entire ignition system (see MR 364, Mechanics, 17A, Ignition),
– check the hydraulic tappets if there is camshaft noise (seeMR 364 Mechanics, 11A, Top and front of engine).
– Carry out the steps "according to the repair".
If the fault is still present, deal with the other faults then proceed to the conformity check.
AFTER REPAIREnsure that all the faults have been dealt with.
Clear the stored faults. Do not clear the programming.
To check that the system has been properly repaired:
- there must be no further electrical faults,
- programming has been carried out,
- the engine should be warm (minimum temperature 75°C),
- running at idle speed with all the electrical consumers activated for 15 minutes,
- if the fault is still absent, check that the catalytic converter is in working order. Use
command SC006 Run OBD Test: Catalytic converter.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of faults17B
17B - 84V12 MR-372-J84-17B000$405.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DF612
PRESENT
OR
STOREDOIL VAPOUR DEFREEZE RESISTOR CIRCUIT
CO.0 : open circuit or short circuit to earth
NOTESPriority for dealing with a combination of faults:
If the faults DF002 Air temperature sensor circuit, DF004 Turbocharging pressure
circuit, DF009 Gang 2 pedal potentiometer circuit or DF046 Battery voltage are
present, handle them first.
Conditions for applying the fault finding procedure to stored faults:
The fault appears after the ignition has been switched on.
Check the cleanliness and condition of the oil vapour defreeze resistor relay connections.
Clean or replace as necessary.
Measure the resistance of the defreeze resistor relay between tracks 1 and 2.
Replace the relay if the resistance is not:21at - 40 °C
9.5at 20 °C
13.4at 120 °C
With the ignition on, check for + 12 V on track 1 of the defreeze resistor relay.
Repair if necessary.
Disconnect the battery.
Disconnect the computer. Check the cleanliness and condition of the connections.
Using the Universal bornier, check the insulation, continuity and the absence of interference resistance for
the following connection:
Computer, connector B, track L2 track 2 of the oil vapour defreeze relay
Repair if necessary.
If the fault is still present, deal with the other faults, then proceed to the conformity check.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-92V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Engine
speedPR055: Engine speedIndicates the engine's speed
of rotation in rpm.
0 rpm < PR055 < 500 rpmIn the event of a fault
apply the interpretation
for DF154 Flywheel
signal sensor circuit.
2
Motorised
throttlePR014: Idling speed
correctionShows engine idling speed
correction value.
PR014= 0rpm.
The idle speed regulator
performs all of the
calculations that allow the idle
speed actuator to be
controlled physically: the
motorised throttle. The
functional component of the
regulator is adaptive
(variation programming and
ageing).WITHOUT
3 PR054: Idle speed
regulationACTIVE
INACTIVEIf ACTIVE apply the
interpretation for ET054
Idle speed regulation.
4 PR010: Idle speed
regulation
setpointThe idle speed regulation
setpoint depends on the
coolant and oil temperature,
the position of the gear lever,
and which electrical
consumers are operating.
752 rpm. < PR010
< 1216 rpm.
If a manifold pressure sensor
fault is present or stored, the
idle speed setting is 896 rpm.In the event of a fault
apply the interpretation
for ET054, Idle speed
regulation.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-113V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Engine
speedPR055: Engine
speedIndicates the engine's speed of
rotation in rpm.
700 rpm < PR055 < 6500 rpmIn the event of a
fault, apply the
interpretation for
DF154 Flywheel
signal sensor
circuit.
2
Motorised
throttlePR014: Idling
speed
correctionShows engine idling speed
correction value.
0 rpm < PR014 < 224 rpm.
The idle speed regulator performs all
of the calculations that allow the idle
speed actuator to be controlled
physically: the motorised throttle.
This regulator has a built-in adaptive
component (variation and ageing
programming).WITHOUT
3ET054: Idle speed
regulationACTIVE
INACTIVEIf INACTIVE apply
the interpretation for
ET054 Idling speed
regulation.
4 PR010: Idle speed
regulation
setpointThe idle speed regulation setpoint
depends on the coolant and oil
temperature, the position of the gear
lever, and which electrical
consumers are operating.
752 rpm < PR010 < 1216 rpm.
If a manifold pressure sensor fault is
present or stored, the idle speed
setting is 896 rpm.In the event of a
fault, apply the
interpretation of
ET054 Idle speed
regulation.
JSAA741.0

PETROL INJECTION
Fault finding – Help17B
17B - 173V12 MR-372-J84-17B000$810.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – Help
ELECTRICAL RESISTANCE OF COMPONENTS ON THE F4R ENGINE
Ambient temperature ~ 20 °C
Injectors14.5 ±5%
Throttle valve motor2.3 ±10%
Fuel vapour absorber solenoid valve 25 ±20%
Camshaft dephaser solenoid valve 7.2 ±10%
Pencil coils Primary:
Secondary: 0.5 ±5%
10.7 k ±15%
Flywheel signal sensor 230 ±20%
Upstream oxygen sensor heating 9 ±10%
Downstream oxygen sensor heating 9 ±10%
JSAA741.0
MR-372-J84-17B000$810.mif

PETROL INJECTION
Fault finding – Fault Finding Chart17B
17B - 180V12 MR-372-J84-17B000$900.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ALP 3 Idle speed faults
NOTESFill in ALP 3 after a complete check using the diagnostic tool.
(Use the relevant section in the Workshop Repair Manual to carry out certain
operations).
WARNING
Never drive the vehicle without checking first that there are no throttle valve
faults.
Check that the oil level is not too high.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery system (manifold/cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Check the condition of the pencil coils and the cleanliness of their connections.
Check the electrical resistance of the pencil coil secondary circuits.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the tank vent is not blocked.
Check that the fuel is of the correct type.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
Check the hydraulic tappets if there is camshaft noise.
AFTER REPAIRRepeat the conformity check from the start.
JSAA741.0

PETROL INJECTION
Fault finding – Fault Finding Chart17B
17B - 181V12 MR-372-J84-17B000$900.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ALP 4 Faults occurring while driving
NOTESFill in ALP 4 after a complete check using the diagnostic tool.
(Use the relevant section in the Workshop Repair Manual to carry out certain
operations).
WARNING
Never drive the vehicle without checking first that there are no throttle valve
faults.
Check that the oil level is not too high.
Check the condition of the pencil coils and the cleanliness of their connections.
Check the electrical resistance of the pencil coil secondary circuits.
Check the condition and conformity of the spark plugs.
Check the mounting, cleanliness and condition of the flywheel signal sensor.
Check the flywheel signal sensor air gap.
Check the condition and cleanliness of the flywheel.
Check that the air filter is not clogged.
Check that the air inlet circuit is not blocked.
Check that throttle valve is not clogged.
Check the inlet system sealing, from the throttle to the cylinder head.
Check that the fuel vapour absorber bleed is not disconnected or jammed open.
Check that there are no leaks in the fuel vapour absorber bleed system.
Check that there are no leaks in the braking assistance system.
Check that there are no leaks in the oil vapour recovery system (manifold/cylinder head).
Check that there are no leaks around the manifold pressure sensor.
Check that there are no leaks around the air temperature sensor.
Check that the tank vent is not blocked.
Check that the fuel is of the correct type.
Check that there are no leaks in the fuel system, from the tank to the injectors.
Check that there are no kinked hoses (especially after a removal operation).
Check the fuel flow rate and pressure.
Check that the injectors are working properly.
Check that the exhaust system is not blocked and the catalytic converter not clogged.
Check the timing setting.
Check the cylinder compressions.
Check the hydraulic tappets if there is camshaft noise.
AFTER REPAIRRepeat the conformity check from the start.
JSAA741.0