brake sensor RENAULT TWINGO 2009 2.G Chasiss ABS Workshop Manual

38C-7
MR-413-X44-38C000$094_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - List and location of components
The computer/hydraulic unit assembly:
●Located to the left of the bulkhead in the engine compartment.
Front wheel sensors:
●Screwed into the stub-axle, each front sensor has an intermediate connector located behind the plastic wheel
arch liner.
Rear wheel sensor intermediate connectors:
●Located in a sealed unit under the vehicle.
Rear wheel sensors:
●Screwed into the rear brake drum flange.
Brake light switch:
●Located on the pedal assembly.
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$094_eng.mif

38C-8
MR-413-X44-38C000$141_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Operating diagram
Number Description
1Computer
2Hydraulic unit (8 solenoid valves)
3Electric power assisted steering
4Instrument panel - engine management
5Passive brake servo
6Brake lights switch
7Diagnostic socket
8Battery
9Wheel speed sensor
10Target
11Brake discs
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$141_eng.mif

38C-10
MR-413-X44-38C000$235_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Role of components
Wheel speed sensor:
Gives the speed of each of the vehicle's wheels. The analysis of the right/left-hand speeds makes it possible to
calculate in what direction the vehicle is turning.
Brake lights switch:
Visual indication of the brake pedal position. It makes it possible to tell if the driver is braking or not.
Wire connection (vehicle speed):
The ABS computer is best suited to transmit the vehicle speed to the other computers. To do this, the ABS transmits
the vehicle speed on the CAN network. However, some computers are not connected to the CAN network, this is
why the ABS is fitted with a "vehicle speed" wire output. Fault finding is not run on this connection by the ABS
computer. This enables the consumers of this signal to perform the necessary checks during their own fault finding
procedure, or to check the connection by observing the customer complaint on the consumer (for example, increase
in the volume of the radio if the speed increases, electric power-assisted steering).
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$235_eng.mif

38C-14
MR-413-X44-38C000$423_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Fault summary table
Tool fault Associated DTC Diagnostic tool title
DF00150 Short circuit Computer supply
DF0065015 Front left-hand wheel speed sensor circuit
DF0075035 Rear left-hand wheel speed sensor circuit
DF008501F Front left-hand wheel speed sensor signal
DF009503F Rear left-hand wheel speed sensor signal
DF01050D3 Pump motor circuit
DF01750C3 Computer
DF0205140 Tachometric index programming
DF0265005 Front right-hand wheel speed sensor circuit
DF0275025 Rear right-hand wheel speed sensor circuit
DF028500F Front right-hand wheel speed sensor signal
DF029502F Rear right-hand wheel speed sensor signal
DF0555143 Vehicle parameter programming
DF06650E2 No injection multiplex signal
DF0905041 Front right-hand wheel target
DF0915042 Front left-hand wheel target
DF0925043 Rear right-hand wheel target
DF0935044 Rear left-hand wheel target
DF0965148 Computer internal electronic irregularity
DF09850E4 No UCH multiplex signal
DF1195150 Gearbox type configuration
DF121D11D Torque requested not available
DF15250E6 Multiplex network
DF18850C6 Brake light switch circuit
DF219D132 ABS multiplex signal consistency
DF2295002 Front right-hand wheel speed
DF2305011 Front left-hand wheel speed
DF2315021 Rear right-hand wheel speed
DF2325031 Rear left-hand wheel speed
DF250D117 Engine speed multiplex signal
DF251D118 Effective average torque multiplex signal
DF252D119 Torque request multiplex feedback signal
DF253D120 Recalculated torque multiplex signal
DF254D12F Resisting torque multiplex signal
DF31150E3 No BVR multiplex signal
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$423_eng.mif

38C-21
MR-413-X44-38C000$470_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF008
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL SPEED SENSOR SIGNAL
1.DEF: Inconsistent sensor signal
2.DEF: No vehicle speed signal
3.DEF: Inconsistent vehicle speed
NOTESPriorities when dealing with a number of faults:
Deal with fault DF006 Front left wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
Check the connection and condition (possible damage to the wiring) of the connector of component 1094.
Check the connection and condition (possible damage to the wiring) of the connector of component 153.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check for a voltage of approximately 12 V between the two connections of the connector of component 153 near
component 1094.
If a 12 V feed is not present, contact the Techline.
If all the checks are in order, swap the 2 front wheel speed sensors. Clear the computer fault memory.
Switch off the ignition. Switch the ignition back on and carry out a road test.
If a fault, which was initially registered as DF008 Front left-hand wheel speed sensor signal has become
present DF028 Front right-hand wheel speed sensor signal, replace the wheel speed sensor
(see MR 411 Mechanical systems, 38C, Wheel speed sensor: Removal - Refitting).
If the fault stays on the same side, the target is faulty, replace the active sensor bearing.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF008

38C-22
MR-413-X44-38C000$470_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF009
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL SPEED SENSOR SIGNAL
1.DEF: Inconsistent sensor signal
2.DEF: No vehicle speed signal
3.DEF: Inconsistent vehicle speed
NOTESPriorities when dealing with a number of faults:
Deal with fault DF007 Rear left-hand wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
Check the connection and condition (possible damage to the wiring) of the connector of component 1094.
Check the connection and condition (possible damage to the wiring) of the connector of component 151.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check for a voltage of approximately 12 V between the two connections of the connector of component 151 near
component 1094.
If a 12 V feed is not present, contact the Techline.
If all the checks are in order, swap the 2 rear wheel brake drums. Clear the computer fault memory.
Switch off the ignition. Switch the ignition back on and carry out a road test.
If the fault initially declared as DF009 "Rear left-hand wheel speed sensor signal" has become present DF029
"Rear right-hand wheel speed sensor signal", replace the complete drum (see MR411 Mechanical systems,
33A, Rear axle components).
If the fault remains on the same side, replace the speed sensor (see MR411 Mechanical systems, 38C Wheel
speed sensor, Removal - Refitting).
Important, do not forget to refit the drums to the correct wheels.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF009

38C-30
MR-413-X44-38C000$470_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF028
PRESENT
OR
STOREDFRONT RIGHT-HAND WHEEL SPEED SENSOR SIGNAL
1.DEF: Inconsistent sensor signal
2.DEF: No vehicle speed signal
3.DEF: Inconsistent vehicle speed
NOTESPriorities when dealing with a number of faults:
Deal with fault DF026 Front right wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
Check the connection and condition (possible damage to the wiring) of the connector of component 1094.
Check the connection and condition (possible damage to the wiring) of the connector of component 152.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check for a voltage of approximately 12 V between the two connections of component 152 near
component 1094.
If a 12 V feed is not present, contact the Techline.
If all the checks are in order, swap the 2 front wheel speed sensors. Clear the computer fault memory.
Switch off the ignition. Switch the ignition back on and carry out a road test.
If a fault, which was initially registered as DF028 Front right-hand wheel speed sensor signal has become
present DF008 Front left-hand wheel speed sensor signal, replace the wheel speed sensor (see MR411
Mechanical systems, 38C, Wheel speed sensor: Removal - Refitting).
If the fault stays on the same side, the target is faulty, replace the active sensor bearing.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF028

38C-31
MR-413-X44-38C000$470_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF029
PRESENT
OR
STOREDREAR RIGHT-HAND WHEEL SPEED SENSOR SIGNAL
1.DEF: Inconsistent sensor signal
2.DEF: No vehicle speed signal
3.DEF: Inconsistent vehicle speed
NOTESPriorities when dealing with a number of faults:
Deal first with fault DF027 Rear right-hand wheel speed
sensor circuit if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
Check the connection and condition (possible damage to the wiring) of the connector of component 1094.
Check the connection and condition (possible damage to the wiring) of the connector of component 150.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
Check for a voltage of approximately 12 V between the two connections of component 150 near
component 1094.
If a 12 V feed is not present, contact the Techline.
If all the checks are in order, swap the 2 rear brake drums. Clear the computer fault memory.
Switch off the ignition. Switch the ignition back on and carry out a road test.
If the fault initially declared as DF029 Rear right-hand wheel speed sensor circuit signal has become present
DF009 Rear left-hand wheel speed sensor circuit signal, replace the complete drum. (see MR411 Mechanical
systems, 33A Rear axle components).
If the fault remains on the same side, replace the speed sensor (see MR411 Mechanical systems, 38C Wheel
speed sensor, Removal - Refitting).
Important, do not forget to refit the drums to the correct wheels.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF029

38C-34
MR-413-X44-38C000$470_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF090
PRESENT
OR
STOREDFRONT RIGHT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF026 Front right wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF090

38C-35
MR-413-X44-38C000$517_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
DF091
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF006 Front left wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test (in excess of 12 mph (20 km/h)
for 2 minutes).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in
good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the conformity of the target (condition, number of teeth = 48) using the special command SC001 Check
target teeth.
If there is non-conformity, replace the target.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF091
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$517_eng.mif