rear spring RENAULT TWINGO 2009 2.G Chasiss User Guide

33A-29
REAR AXLE COMPONENTS
Rear suspension spring: Removal - Refitting
33A
aRefit the shock absorber springs into their housings.
aCompress the rear axle.
aRefit the lower shock absorber mounting bolts.
aTorque tighten the shock absorber lower bolts
(105 Nm).
II - FINAL OPERATION.
aRemove the component jack.
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
119400

33A-34
REAR AXLE COMPONENTS
Rear stub axle carrier: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the rear wheel (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .aUnclip the parking brake cable from the calliper at
(1) .
aRemove:
-the brake calliper mounting bolts (2) ,
-the "brake calliper mounting - brake calliper" as-
sembly.
aAttach the "brake calliper mounting - brake calliper"
assembly to the suspension spring.
aRemove the rear brake disc (see 33A, Rear axle
components, Rear brake disc: Removal - Refit-
ting, page 33A-11) . Equipment required
component jack
Tightening torquesm
new bolts of the rear
stub axle carrier53 N.m
lower bolt of the rear
shock absorber105 N.m
new bolts of the brake
calliper mounting105 Nm
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468

33A-38
REAR AXLE COMPONENTS
Complete rear axle system: Removal - Refitting
33A
aUnclip the parking brake cables (3) on the reservoir.
aOpen the ABS sensor connector protective unit (4) .aDisconnect the ABS sensor connectors (5) .
aRemove:
-the brake hose lower unions (6) ,
-the rear suspension springs (see 33A, Rear axle
components, Rear suspension spring: Remov-
al - Refitting, page 33A-28) .
119652
119438
119437
119339

33A-42
REAR AXLE COMPONENTS
Complete rear axle system: Removal - Refitting
33A
2 - Refitting
aLower the lift.
aPosition the bearing centring devices (12) opposite
the centring holes.
aRefit the rear axle bearing bolts.
aTorque tighten the rear axle bearing bolts (62 Nm).
aRemove the safety strap(s).
aRaise the lift.
aRefit:
-the rear suspension springs (see 33A, Rear axle
components, Rear suspension spring: Remov-
al - Refitting, page 33A-28) ,
-the brake hose lower unions.
aTorque tighten the brake hose lower unions (17
Nm).
aConnect the ABS sensor connectors.
aClose the ABS sensor connector protective unit.
aClip the parking brake cables onto the reservoir.
aPosition the parking brake cables on the parking
brake compensator.
aCheck that the parking brake cable stops are proper-ly inserted in their housings.
III - FINAL OPERATION.
aAdjust the parking brake cables (see 37A, Mechan-
ical component controls, Parking brake lever:
Removal - Refitting, page 37A-46) .
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aRemove the pedal press.
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .
119651