rear spring RENAULT TWINGO 2009 2.G Chasiss Workshop Manual

TWINGO - Chapitre 3
Contents
Pages
TWINGO - Chapitre 3ContentsPages
30A GENERAL INFORMATION
Brake circuit: Operating
diagram 30A-1
Brake circuit: Precautions for
the repair 30A-2
Braking circuit: Bleed 30A-4
Brake circuit: Tightening
torque 30A-6
Rigid brake pipe: Repair 30A-13
Brake fluid: Specifications 30A-18
Brake: Specifications 30A-19
Steering: Tightening torque 30A-20
Axle assemblies: Check 30A-23
Underbody heights:
Adjustment value 30A-24
Front axle system:
Tightening torque 30A-27
Front axle assembly:
Adjustment values 30A-31
Front axle system:
Adjustment 30A-36
Rear axle system: Tightening
torque 30A-37
Rear axle assembly:
Adjustment values 30A-3831A FRONT AXLE COMPONENTS
Front brake pads: Removal -
Refitting 31A-1
Front brake hose: Removal -
Refitting 31A-6
Front brake calliper: Removal
- Refitting 31A-8
Front brake calliper: Repair 31A-12
Front brake calliper
mounting: Removal -
Refitting 31A-14
Front brake disc protector:
Removal - Refitting 31A-18
Front brake disc: Removal -
Refitting 31A-19
Front brake disc: Description 31A-22
Front driveshaft hub carrier:
Removal - Refitting 31A-23
Front hub carrier bearing:
Removal - Refitting 31A-26
Front shock absorber and
spring: Removal - Refitting 31A-29
Front driveshaft lower arm:
Removal - Refitting 31A-33
Front driveshaft lower arm
ball joint: Removal - Refitting 31A-40
Front axle subframe:
Removal - Refitting 31A-43

Contents
Radiator mounting cross
member: Removal - Refitting 31A-51
Front anti-roll bar: Removal -
Refitting 31A-52
33A REAR AXLE COMPONENTS
Rear brake pads: Removal -
Refitting 33A-1
Rear brake hose: Removal -
Refitting 33A-4
Rear brake calliper: Removal
- Refitting 33A-7
Rear brake calliper
mounting: Removal -
Refitting 33A-9
Rear brake disc: Removal -
Refitting 33A-11
Rear brake disc: Description 33A-13
Rear brake lining: Removal -
Refitting 33A-14
Rear brake cylinder:
Removal - Refitting 33A-17
Rear brake drum: Removal -
Refitting 33A-19
Rear brake drum:
Description 33A-21
Rigid brake pipe: Removal -
Refitting 33A-22
Shock absorber: Removal -
Refitting 33A-24
Rear suspension spring:
Removal - Refitting 33A-28
Rear drum bear ing: Removal
- Refitting 33A-30
Rear stub axle carr ier:
Removal - Refitting 33A-32
Complete rear axle system:
Removal - Refitting 33A-37 31A FRONT AXLE COMPONENTS
35A WHEELS AND TYRES
Wheel: Removal - Refitting 35A-1
Wheel: Balancing 35A-4
Tyres: Identification 35A-7
Tyres: Removal - Refi tting 35A-8
Tyre pressure: Identification 35A-10
Wheel r im: Identifi cation 35A-11
36A STEERING ASSEMBLY
Steering box: Removal -
Refitting 36A-1
Track rod: Removal -
Refitting 36A-2
Axial ball joint linkage:
Removal - Refitting 36A-4
Steering column: List and
location of components 36A-6
Steering column: Removal -
Refitting 36A-7
Steering box gaiter: Removal
- Refitting 36A-16
Bulkhead seal: Removal -
Refitting 36A-17
Intermediate shaft: Removal
- Refitting 36A-18
Steering column adjustment
handle: Removal - Refitting 36A-21
Steering wheel: Removal -
Refitting 36A-23
36B POWER ASSISTED STEERING
Power-assisted steering
computer: Removal -
Refitting 36B-1

33A-9
REAR AXLE COMPONENTS
Rear brake calliper mounting: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aRemove:
-the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake pads (see 33A, Rear axle compo-
nents, Rear brake pads: Removal - Refitting,
page 33A-1) .aRemove:
-the brake calliper guide pin bolts (1) ,
-the brake calliper from the mounting.
aAttach the brake calliper to the suspension spring.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the brake calliper mounting bolts (2) ,
-the brake calliper mounting. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Tightening torquesm
bolts of the brake calli-
per mountingXXX
new bolts of the brake
calliper guide pins105 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468
132465

33A-11
REAR AXLE COMPONENTS
Rear brake disc: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
Brake discs cannot be reground. If there is excessive
scoring or wear, they will need to be replaced (see
30A, General information, Brake: Specifications,
page 30A-19) .
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake pads (see 33A, Rear axle compo-
nents, Rear brake pads: Removal - Refitting,
page 33A-1) .aRemove:
-the brake calliper mounting bolts (1) ,
-the "brake calliper mounting - brake calliper" as-
sembly.
aAttach the "calliper mounting - brake calliper" to the
shock absorber spring.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the hub's nut cover (2) . Equipment required
par ts washer
Tightening torquesm
new hub nut175 N.m
brake calliper mounting
bolts105 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132467
132456

33A-14
REAR AXLE COMPONENTS
Rear brake lining: Removal - Refitting
33A
Replace all the brake pads on one axle at the same
time. Never mix brake pads of different brands or qual-
ities.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRelease the parking brake.
aRemove:
-the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake drums (see 33A, Rear axle compo-
nents, Rear brake drum: Removal - Refitting,
page 33A-19) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the lower return spring (1) , then the upper
return spring (2) using brake shoe pliers.aFit pliers (3) onto the slave cylinder pistons.
aRemove:
-the side retainer springs (4) of the segments, keep-
ing the connecting rod (5) in contact with the brake
backing plate (6) ,
-the leading shoe (7) ,
-the link rod (8) ,
-the trailing shoe (9) .
aUncouple the parking brake cable from the parking
brake lever.
86561
86560

33A-15
REAR AXLE COMPONENTS
Rear brake lining: Removal - Refitting
33A
aRemove the leading shoe:
-the spring (10) ,
-the adjustment lever (11) .
REFITTING
I - REFITTING PREPARATIONS OPERATION
aRemove any dust from the drums and the flanges
using the cleaning station.
aLightly grease the support linkage thread.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the leading shoe:
-the adjustment lever,
-the spring.
aConnect the parking brake cable to the parking
brake lever.
aRefit:
-the trailing shoe.
86559
117348
Note:
The brake mechanism components are different
on the left and r ight-hand sides, so it is important
not to confuse them.
Note:
On the left-hand brake: the bolt thread has a
right-hand thread.
On the right-hand brake: the bolt has a left-hand
thread.

33A-16
REAR AXLE COMPONENTS
Rear brake lining: Removal - Refitting
33A
-the linkage,
-the leading shoe,
-the side retainer springs of the segments, keeping
the connecting rod in contact with the brake back-
ing plate,
aRefit the lower return spring, then the upper return
spring using brake shoe pliers.
aCheck that the parking brake cable is correctly posi-
tioned on the parking brake lever.
aRemove the pliers from the slave cylinder pistons.aUse a screwdriver to adjust the piston ring diameter
with the linkage to obtain a diameter of 202.45 mm ±± ± ±
0.25.
aCarry out the same adjustment on the other side.
aAdjust the handbrake if the lever stops between the
first and second positions of the parking brake le-
ver's travel (see 37A, Mechanical component con-
trols, Parking brake lever: Adjustment, page
37A-48) .
III - FINAL OPERATION.
aRefit:
-the rear brake drums (see 33A, Rear axle compo-
nents, Rear brake drum: Removal - Refitting,
page 33A-19) ,
-the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aAdjust the brake pads by depressing the brake pedal
repeatedly.
aCheck that the automatic wear take up system is
working properly (characteristic « click » from the
drums when the brake pedal is repeatedly de-
pressed).
116013
86557

33A-17
REAR AXLE COMPONENTS
Rear brake cylinder: Removal - Refitting
33A
REMOVAL
I - OPERATION FOR PREPARATION OF PART
CONCERNED
aPosition the vehicle on a lift ( (see Vehicle: Towing
and lifting) ).
aRelease the parking brake.
aRemove:
-the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake drum (see 33A, Rear axle compo-
nents, Rear brake drum: Removal - Refitting,
page 33A-19) .
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the upper return spring (1) using brake
shoe pliers.
aRemove the brake shoes.aUndo the rigid brake pipe union (2) on the rear brake
cylinder.
aFit a cap on the rigid brake pipe union.
aRemove:
-the rear brake cylinder bolt (3) on the flange,
-the rear brake cylinder. Tightening torquesm
rear brake cylinder bolt
on the flange14.5 Nm
rigid brake pipe union
on the rear brake cylin-
der15 Nm
108343
119341
Note:
Expect some br ake fluid to run out.

33A-18
REAR AXLE COMPONENTS
Rear brake cylinder: Removal - Refitting
33A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aRemove any dust from the drums and the flanges
using the cleaning station.
aCheck the condition of the brake cylinder boots and
pistons (replace any faulty parts).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the rear brake cylinder,
-the rear brake cylinder bolt on the flange,
-the rigid brake pipe union on the rear brake cylin-
der,
-the upper return spring using brake shoe pliers.
aTorque tighten:
-the rear brake cylinder bolt on the flange (14.5
Nm),
-the rigid brake pipe union on the rear brake cyl-
inder (15 Nm).
III - FINAL OPERATION.
aRefit:
-the rear brake drum (see 33A, Rear axle compo-
nents, Rear brake drum: Removal - Refitting,
page 33A-19) ,-the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aBleed the brake circuit (see 30A, General informa-
tion, Braking circuit: Bleed, page 30A-4) .
aAdjust the brake pads by depressing the brake pedal
repeatedly.
117348

33A-28
REAR AXLE COMPONENTS
Rear suspension spring: Removal - Refitting
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove the rear wheels (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUsing a block, bring the component jack into con-
tact under the rear axle, near the shock absorber.
aMark the position where the springs are fitted.
aRemove the lower bolt (1) from the shock absorber.
aRemove the component jack.
aRepeat these operations on the opposite side.aRemove the springs by removing the component
jack.
aLeave the rear axle suspended.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aUsing a block, bring the component jack into con-
tact under the rear axle, near the shock absorber. Equipment required
component jack
Tightening torquesm
shock absorber lower
bolts105 Nm
119340
119547
119546