ignition RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel User Guide

83A-31
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
SUB-FUNCTION: TRIP COMPUTER
*ADAC: Trip Computer
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Instrument panel
warning light
operation checkAC009:Instrument
panel warning
lightsIllumination of all of the
warning lights
simultaneously on the
displayImportant: This command
causes the Airbag system
stored fault to occur again
(see 88C Airbag and
pretensioners).
–Before running the
command:
Deal with all of the Airbag
faults.
(see 88C, Airbag and
pretensioners).
–After running the
command:
Clear the Airbag system
stored faults.
If one or more warning lights
do not come on, contact
Techline.
Backlighting
operation checkAC010:LightingGradual illumination of
the instrument panel
backlightingWITHOUT
Instrument panel
buzzer checkAC006:BuzzerInstrument panel buzzer
operation–If the buzzer is faulty,
contact Techline.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
ADAC* button
status signalET030:ADAC* scroll
button
Button
depressedDEPRESSED
In the event of a fault, consult the
interpretation of status ET030
ADAC* scroll button.
Button
releasedRELEASED
Clock setting
button status
signalET095:Clock setting
button
Button
depressedDEPRESSED
Contact the Techline.Button
releasedRELEASED

83A-32
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION : GAUGING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fuel sender
operation checkPR040:Current fuel levelThe current fuel level
depends on the vehicle
body movements.In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.
Filtered fuel
level checkPR041:Filtered fuel levelThe filtered fuel level is
independent of the
variations created by the
vehicle body movements.In the event of a fault, consult the
interpretation of parameter
PR041 Filtered fuel level.
Fuel sender
resistance
checkPR002:Fuel sender unit
resistanceThe fuel sender resistance
depends on the fuel level.
In reserve: 260 ΩΩ Ω Ω
Full: 38 ΩΩ Ω ΩIf R < 5 ΩΩ Ω Ω
or R> 350 ΩΩ Ω Ω
: Faulty
fuel sender.
In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.

83A-33
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB FUNCTION: ODOMETRY IN KM
SUB FUNCTION: ODOMETRY IN MILES
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in kmPR025:Odometry in kmDisplays the vehicle
distance in km.WITHOUT
Check the
distance before
oil service in kmPR005:Distance to next oil
service: current
value in kmDisplays the distance
remaining in kms before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in kmPR007:Oil change
frequency in km.Initial oil service interval
in km.WITHOUT
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in milesPR026:Odometer in milesDisplays the vehicle
distance in miles.WITHOUT
Check the
distance before
oil service
in milesPR023:Oil service
interval: current
value in milesDisplays the distance
remaining in miles before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in milesPR024:Oil change
frequency in miles.Initial oil service interval in miles.

83A-37
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET030
ADAC* SCROLL BUTTON
NOTESVehicle under + after ignition feed.
“RELEASED”
STATUS
button
pressed
*ADAC: Trip ComputerCheck the condition and connection of the instrument panel connector,
component code 247.
Press and hold the Trip Computer button and check the continuity between
connection MAM and connection 47K of component 145.
If there is no continuity, replace component 145 (see MR 411, Mechanical, 84A,
Controls - Signals, Wiper switch: Removal - Refitting).
Check the continuity and insulation to + 12 V on:
Connection 47K between component 145 and component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check the earth and insulation to + 12 V of:
–Connection MAN between component 145 and the chassis earth.
–Connection MAN between component 145 and the chassis earth.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET030 / TDB_V08_ET030

83A-40
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET245
INDICATORS
NOTESCheck for the absence of faults on the indicators in the UCH field before starting
fault finding.
Vehicle under + after ignition feed.
If the indicator lights are not displayed or are inconsistent with the position of the control, carry out the following
fault finding procedure.
If status ET245 INDICATORS is INACTIVE and the control is activated:
Check that the connector of component 247 is in good condition and correctly connected.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the connector, otherwise replace the wiring.
Check the continuity of:
Connection 64C between component 645 and component 247 (left-hand indicator)
Connection 64D between component 645 and component 247 (right-hand indicator)
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET245 / TDB_V08_ET245

83A-50
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 1
VEHICLE CHECK
Check the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
Check the condition and connection of the instrument panel connector, component
code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check instrument panel supply fuse MIN (5 A), component code 247 on the passenger
compartment fuse box, component code 1016 and the condition and cleanliness of
the contacts.
Check the instrument panel after ignition supply fuse MIN (15 A), component code
247 on the passenger compartment fuse box, component code 1016, and the
condition and cleanliness of the contacts.

83A-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 2
NOTESVehicle under + after ignition feed.
VEHICLE CHECKUse the Universal bornier to check the following connections on the vehicle diagnostic
socket, component code 225:
BP19 "+ protected battery feed" of component 225.
•MAN (if left-hand drive) of component 225.
•MAM (if right-hand drive) of component 225.
•NAM, the earth of component 225.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Check the earth of connection MAN of the instrument panel, component code 247.
If the earth MAN is poor, check the insulation to + 12 V and check the continuity of
the following connection:
•MAN of component 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Check for + 12 V on connection AP43 and connection BP49 of the instrument panel,
component code 247.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If there is no + 12 V, check the insulation to earth and the continuity of the following
connections:
•AP43 between components 247 and 1016,
•BP49 between components 247 and 1016.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.

83A-52
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2 The fuel level indicator does not display full
NOTESThe fuel tank must be filled with the ignition switched off (advise the customer to remove
the key).
Ideally the customer must fill the tank with at least 15 litres.
See Wiring diagram Technical Note, New Twingo.
Ask the customer if the tank is filled up under the
following conditions:
–the customer filled the tank up to the 3
rd cut-out
–the customer has changed filling station
–the customer filled the tank in a flat-level station (not
on a slope).
Did the customer fill the tank while observing all of
these conditions?Ask the customer to return just after
having filled the tank under the conditions
mentioned above.
NO
YES
A
TDB_V04_ALP2/TDB_V08_ALP2

83A-53
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2
CONTINUED 1
With the ignition off, disconnect the fuel sender
connector, component code 833 and then check
the resistance using a multimeter.
The value should be: 38 ΩΩ Ω Ω
.
Is the value measured less than 38 ΩΩ Ω Ω
?Replace the fuel sender, component code
833 (see MR 411, Mechanical, 19C, Fuel
tank, Sender: Removal - Refitting).
If the fault is still present, contact Techline.
Compare the value measured to the value supplied
by the CLIP tool.
Is the value measured and the value provided
by the CLIP tool the same as or approximately
± 5 ΩΩ Ω Ω
?
A
YES
NO
YES
NOC
YES
B

83A-59
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.Replace the instrument panel,
component code 247 (see
MR 411, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
Record the resistance value provided by the CLIP tool.
Compare the value from the CLIP tool with the warning
resistance, which should be 260 ΩΩ Ω Ω
.
Is this value above or equal to 260 ΩΩ Ω Ω
?Contact the Techline.
Rock the vehicle and check whether the resistance changes by
± 5 ΩΩ Ω Ω
.
Is there a change in the resistance value?Contact the Techline.
NO
YES
YES
NO
YES
NO
A
TDB_V04_ALP5/TDB_V08_ALP5