RENAULT TWINGO 2009 2.G Electrical Equipment - Parking Distance Control Owner's Guide

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 31V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08
ET003
PARKING PROXIMITY SENSOR FUNCTION
NOTESSpecial notes:
If the parking proximity sensor system is suspended or deactivated, the parking
proximity sensor switch indicator light comes on.
This status indicates whether the parking distance control system is on or off:
ET003: READY This means that, when reversing, the parking distance control detects
obstacles and the buzzer sounds (the parking distance control switch
indicator light goes out).
ET003: DETECTING This information is displayed when reverse gear is engaged.
This status indicates that the parking distance control system has
detected an obstacle.
ET003: SUSPENDED This means the parking distance control system is switched off
(no detection possible). The suspension is temporary because the
parking distance control system will come back on after the ignition
is switched off and on. Briefly pressing the parking distance control
switch enables the system to be suspended or reactivated manually.
ET003: DEACTIVATED This means the parking distance control system is switched off
(no detection possible). This suspension is permanent (switching
the + after ignition off and on again will not reactivate the system).
Pressing and holding (3 seconds) the parking distance control
switch enables the system to be deactivated or reactivated.
Check the condition of the fuses F6 (15A), F42 (10A), and replace them if necessary.
If the status does not function as described, check the + 12 V supply on connection LPD between components
1440 and 1016. Check for earth on connection MAN of the connector of component 1440.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for a + 12 V supply on connection AP3. Check for an earth on connection MG of the connector of component
1222.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ ET003/AAP_V08_ ET003

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 32V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08
ET003
CONTINUED
With the ignition off, disconnect the parking proximity sensor switch to check the insulation (against the earth
and + 12 V), continuity and the absence of interference resistance on the following connection:
●Connection code 151W,
Between components 1222 and 1440.
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
If the connection just checked is correct (no open circuit or short circuit) and there is an earth on connection MAN
of the switch but the fault is still present, check the switch operation with an ohmmeter.
Switch not pressed: insulation between connections 151W and MAN.
After pressing the switch: continuity between connections 151W and MAN.
Replace the parking proximity sensor switch if it fails to function as specified.
AFTER REPAIRRepeat the conformity check from the start.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 33V2 MR-413-X44-87F000$660_eng.mif
Vdiag No.: 04 08
ET004
PARKING DISTANCE CONTROL SWITCH
NOTESSpecial notes:
Only apply the interpretation of this status if the position of the parking distance control
switch is not consistent with the information supplied by status (“Brief press” or
“Released”).
There must be no present or stored faults.
Check the condition of fuses F6 (15A), F42 (10A) and replace them if necessary.
Check that there is a + 12 V supply on connection LPD between components 1140 and 1016. Check that there is
an earth on connection MAN of the connector of component 1440.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for a + 12 V supply on connection AP3. Check for earth on connection MG of the connector of component
1222.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition off, disconnect the parking distance control button connector to check the insulation (against
earth and + 12 V), continuity and the absence of interference resistance on the following connection:
Connection code 151W between components 1222 and 1440.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection just checked is OK (no open or short circuit), and there is an earth on track A2 of the switch but
the fault is still present, check the switch operation with an ohmmeter.
Switch not pressed: insulation between connections 151W and MAN.
After pressing the switch: continuity between connections 151W and MAN.
Replace the parking proximity sensor switch if it fails to function as specified.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ ET004/AAP_V08_ ET004

PARKING DISTANCE CONTROL
Fault finding - Parameter summary table87F
87F - 34V2 MR-413-X44-87F000$726_eng.mif
Vdiag No.: 04 08PARKING DISTANCE CONTROL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Left-hand outer sensor distance
PR002Left-hand inner sensor distance
PR003Right-hand outer sensor distance
PR004Right-hand inner sensor distance
PR005Shortest distance calculated
MR-413-X44-87F000$726_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of parameters
87F
87F - 35V2 MR-413-X44-87F000$792_eng.mif
Vdiag No.: 04 08PARKING DISTANCE CONTROL
Fault finding - Interpretation of parameters
PR001
PR002
PR003
PR004
LEFT-HAND OUTER SENSOR DISTANCE
LEFT-HAND INNER SENSOR DISTANCE
RIGHT-HAND OUTER SENSOR DISTANCE
RIGHT-HAND INNER SENSOR DISTANCE
NOTESSpecial notes:
Before searching for a fault with these parameters, make sure no fault is present or
stored. If there is a fault, apply the interpretation for the fault detected by the
diagnostic tool.
Note:
The ultrasonic sensors are very fragile. Therefore, when removing the rear bumper,
be careful not to scratch them.
If the distance displayed equals 0 cm, there are two possible reasons:
1no obstacle has been detected (therefore this is the default value)
2The sensor is malfunctioning, check that there are none of the following faults:
DF002 “LEFT-HAND OUTER SENSOR”, DF003 “LEFT-HAND INNER SENSOR”,
DF004 “RIGHT-HAND OUTER SENSOR”, DF005 '“RIGHT-HAND INNER
SENSOR” and apply the relevant fault finding procedure
Wen the vehicle is close to an obstacle (between 26 and 150 cm), check that the distance evaluated corresponds
to the distance displayed by the diagnostic tool (PR001 to PR004).
If the distance is inconsistent when there is an obstacle present, check that there is nothing interfering with the
measurement (sticker, mud, snow on the rear bumper, etc.).
If the distances displayed by the sensors are inconsistent, check the condition of the sensor(s), check the condition
of the button using status ET003 “Parking distance control function” and ET004 “Parking distance control
switch”. There must be no scratches on the detection component (outer metal section) of the sensors.
Replace the defective sensor.
If the fault is still present, apply the fault finding procedure to the sensor whose distance parameter is incorrect
(even if the diagnostic tool does not report a fault).
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ PR001/AAP_V04_ PR002/AAP_V04_ PR003/AAP_V04_ PR004/
AAP_V08_ PR001/AAP_V08_ PR002/AAP_V08_ PR003/AAP_V08_ PR004
MR-413-X44-87F000$792_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of parameters
87F
87F - 36V2 MR-413-X44-87F000$792_eng.mif
Vdiag No.: 04 08
PR005
SHORTEST DISTANCE CALCULATED
NOTESSpecial notes:
Before searching for a fault with this parameter, make sure that no fault is present or
stored. If there is a fault, apply the interpretation for the fault detected by the
diagnostic tool.
Note:
The ultrasonic sensors are very fragile. Therefore, when removing the rear bumper,
be careful not to scratch them.
This parameter is an average calculated by the computer when an obstacle is
placed between two sensors.
When below 30 cm, the estimated distance is displayed as 0 cm (critical detection
zone with constant warning sound).
With the vehicle close to an obstacle (between 0 and 150 cm), check whether the calculated distance is consistent.
If the distance is inconsistent when there is an obstacle present, check that there is nothing interfering with the
measurement (sticker, mud, snow on the rear bumper, etc.).
If the distance calculated is still inconsistent or if it is continuously displayed as 255 cm, check the condition of the
sensors; the detection part (metallic outer part) must not have any scratches.
Replace the defective sensor.
If the fault is still present, apply the fault finding procedure to the sensor with the inconsistent distance parameter
(even if the diagnostic tool does not detect a fault), consult interpretation of faults, DF002 “Left-hand outer
sensor”, DF003 “Left-hand inner sensor”, DF004 “Right-hand outer sensor”, DF005 “Right-hand inner
sensor”.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ PR005/AAP_V08_ PR005

PARKING DISTANCE CONTROL
Fault finding - Customer complaints
87F
87F - 37V2 MR-413-X44-87F000$858_eng.mif
Vdiag No.: 04 08PARKING DISTANCE CONTROL
Fault finding - Customer complaints
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
NO DIALOGUE WITH THE COMPUTER ALP1
NO BUZZERALP2
WARNING SOUND EMITTED CONTINUOUSLY
(NO OBSTACLE DETECTED)ALP3
BUZZER SOUNDS CONTINUOUSLY
(WITH CARAVAN ATTACHMENT)ALP4
MR-413-X44-87F000$858_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
87F
87F - 38V2 MR-413-X44-87F000$924_eng.mif
Vdiag No.: 04 08PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone
Try the diagnostic tool on another vehicle.
Check:
–The connection between the diagnostic tool and the diagnostic socket (lead in good condition).
–The injection, engine and passenger compartment fuses.
Check the condition of fuses F6 (15A) and F11 (20A) and replace them if necessary.
Check that there is a + 12 V battery feed on connection BP19 of the diagnostic socket. Check that there is an
earth on connections MAM and NAM of the diagnostic socket.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring or replace it.
Check for a + 12 V supply on connection AP3. Check for earth on connection MG of the connector of component
1222.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch off the ignition, and disconnect the parking distance control computer to check the insulation, continuity
and the absence of interference resistance on the following connections:
●Connection code AP3 between components 1222 and 1016.
●Connection code MG between components 1222 and the MG earth.
●Connection code HK between components 1222 and 225.
●Connection code BP19 between components 225 and 1016.
●Connection code NAM between components 225 the earth NAM.
●Connection code MAN between components 225 and earth MAN.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
AAP_V04_ ALP1/AAP_V08_ ALP1
MR-413-X44-87F000$924_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
87F
87F - 39V2 MR-413-X44-87F000$924_eng.mif
Vdiag No.: 04 08
ALP2 No buzzer
NOTESOnly investigate this customer complaint after a full check using the diagnostic tool
(there must be no present or stored faults).
Using the diagnostic tool Main Data screen, check
that the parking distance control system is on.
The status ET003 Parking proximity sensor
function must be READY (and the red warning light
on the parking proximity sensor switch must be off).
Is status ET003 Parking proximity sensor
"READY"?
YES
Using the diagnostic tool's Main Data screen,
check that reverse gear is selected.
The ET001 Reverse gear selected status must be
YES.
Also ensure that the reversing lights come on when
reverse gear is selected.
Is status ET001 YES?
YES
Using the diagnostic tool configuration readings
screen, check that the buzzer volume has not been
switched off (LC001 Buzzer volume should not be
ZERO).
Is the LC001 function ZERO
NO
NOTurn on the parking proximity sensor by
pressing the switch for 1 or 3 s econds (the
red light should go out).
Note:
For more information concerning the
activation of the system, consult the
interpretation of status ET003 Parking
proximity sensor.
NOApply the interpretation of status ET001
Reverse gear engaged.
YESReconfigure the buzzer volume using the
diagnostic tool (command CF001 Buzzer
volume).
AFTER REPAIRCheck that the system is operating correctly.
AAP_V04_ ALP2/AAP_V08_ ALP2

PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
87F
87F - 40V2 MR-413-X44-87F000$924_eng.mif
Vdiag No.: 04 08
ALP2
CONTINUED 1
Using the diagnostic tool configuration reading
screen, check the tone of the buzzer using
configuration reading LC006 “Buzzer tone”.
Is the tone loud enough?
YES
Check the connection and condition of the connector
on the buzzer.
Replace the connector if necessary.
Using the diagnostic tool parameter screen
(PR001 “Left-hand outer sensor distance”,
PR002 “Left-hand inner sensor distance”, PR003
“Right-hand outer sensor distance”, PR004
“Right-hand inner sensor distance”), check that
the detection sensors are detecting obstacles
(between 26 and 150 cm).
Do these parameters display distance values
(with an obstacle in front of the rear bumper)?
YES
NOChange the tone of the buzzer using
configuration CF006 “Tone adjustment”.
NOApply the interpretation of parameters
PR001 '“Left-hand outer sensor
distance”, PR002 “Left-hand inner
sensor distance”, PR003 “Right-hand
outer sensor distance”, PR004 “Right-
hand inner sensor distance”
AFTER REPAIRCheck that the system is operating correctly.