cruise control RENAULT TWINGO 2009 2.G Electrical Equipment - Petrol Injection Owner's Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 348
Page 186 of 348
17B-186V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 2
"INACTIVE"
When the main button is in rest position (or Neutral), status ET042 Cruise control/
speed limiter is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition on the switch connector on the following connection:
●AP10 of component 1081.
Disconnect the switch and with it in the rest position, check the insulation between
the following connections:
●AP10 and 3FX of component 1081.
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 187 of 348
17B-187V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 3
LIMITER
When the driver presses the speed limiter switch, status ET042 Cruise control/
speed limiter becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the driver pressed the switch
in the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 188 of 348
17B-188V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 4
CRUISE
CONTROL
When the driver presses the cruise control switch, status ET042 Cruise control/
speed limiter becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears even though the cruise control button is
pressed, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3FX of component 1081 in
the cruise control position.
If the results of the checks are not correct, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 189 of 348
17B-189V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET045CRUISE CONTROL/SPEED LIMITER SELECTOR SWITCH ON STEERING WHEEL
STATUS
DEFINITIONRESUME: This status indicates that the R button is pressed.
SUSPEND: This status indicates that the 0 is pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
INCREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
DECREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
SUSPENDStatus ET413 becomes SUSPEND when the 0 cruise control button is pressed.
This button is situated to the right of the steering wheel.
RESUMEStatus ET413 becomes RESUME when the R cruise control button is pressed.
This button is situated to the right of the steering wheel.
SIM32_V44_ET045/SIM32_V4C_ET045/SIM32_V50_ET045/SIM32_V54_ET045
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Page 228 of 348
17B-228V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Inconsistency between the request and the vehicle speed. Gear lever in neutral
(manual gearbox) or the N position (automatic gearbox).
SIM32_V44_ET415/SIM32_V4C_ET415/SIM32_V50_ET415/SIM32_V54_ET415
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 229 of 348
17B-229V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 1
STATUS 7:
Inconsistency between the request and the vehicle speed.
STATUS 8:
Automatic transmission in defect mode.
STATUS 9:
Vehicle speed monitoring.
STATUS 10:
Monitoring by injection computer.
Sensor electrical conformity
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control/speed limiter function, due to a driver
request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 Fault memory to reset this status to NONE.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 230 of 348
17B-230V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 2
WITHOUTThis status is present on the diagnostic tool when:
The computer has been reinitialised,
The computer has been reprogrammed.
STATUS 1 Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and when traction
control is requested.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-
lock braking system).
STATUS 2 Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when the vehicle is being driven, with cruise
control active (ET042) and the brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 231 of 348
17B-231V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 3
STATUS 3 Clutch pedal depressed
Manual gearbox only:
The cruise control function is deactivated when the gearbox is not coupled to the
engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical specifications and, in particular, the automatic
gearbox computer configuration (see 88B, multiplex).
STATUS 4 Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
–Either the cruise control is active, or
–the speed limiter is active
–and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703: Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 232 of 348
17B-232V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 4
STATUS 5 Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has
been pressed.
If status ET415 is STATUS 5, consult the interpretation:
–of status ET042 Cruise control/Speed limiter,
–of status ET703 Cruise control/Speed limiter buttons,
–of status ET704 Brake switch no. 1,
–and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults shown
on the diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with any faults that are present or stored
in the injection computer.
If the fault is still present, contact the Techline.
STATUS 6 Gear lever in neutral (manual gearbox) or neutral (automatic transmission).
Status ET415 changes to STATUS 6, when driving, with cruise control active
(ET042) and:
if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
if the gear lever is in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into neutral on an automatic transmission,
test the ABS computer and check the configuration of the tyre size stored in the
computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
Page 233 of 348
17B-233V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 5
STATUS 7 Lack of correlation between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference
in speed.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 "Fault memory".
If status ET415 becomes STATUS 7 where the surface is not uneven, contact
the Techline.
STATUS 8 Automatic gearbox in defect mode.
Status ET415 becomes STATUS 8, when driving with cruise control active (ET042)
and if the automatic transmission is in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic
transmission computer.
Deal with any present or stored faults (see 23A, Automatic transmission,
Interpretation of faults).
Clear the automatic transmission computer memory by running command RZ001.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If the specification STATUS 8 is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.