radio RENAULT TWINGO 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD User Guide

87B -137
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
* RF: radio frequencyET240
KEY FREQUENCY (IN MHZ)
NOTESThere must be no present or stored faults.
SPECIFICATIONS433
NONE
NONE
The vehicle must not be equipped with a locking/unlocking button.
Check that LC097 Key type is definitely "Standard". Otherwise run CF195 Key type
and select "Standard".
WITHThe vehicle must be equipped with a locking/unlocking button.
Check that LC097 Key type is definitely RF*, otherwise run CF195 Key type and
select RF*.
Check the operation of statuses ET045 R.F.* signal received" and ET193 RF* signal
from a key allocated to the vehicle.
If the door locking/unlocking by radio frequency key does not operate, replace the key
and run command SC015 Key allocation.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET240

87B -163
MR-413-X44-87B000$816.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
AC110
TEMPERATURE DISPLAY
NOTESSpecial notes:
Check that the vehicle is equipped with an external temperature sensor.
IMPORTANT
This command lasts approximately 30 seconds.
It makes it possible to check the connection between the display (component code 653) and the UCH
(component code 645).
With the command running, the temperature display should change; if not apply the fault finding procedure below.
Read configuration LC002 External
temperature sensor.
Is the configuration “With”?
YES
Check that LC067 "External temperature display" is "WITH". Otherwise
perform CF171 "Temperature display".
Check the condition and connection of the PE2 40-track UCH connector,
(component code 645) (tabs bent, broken, etc.).
If the connector is faulty and there is a repair method (see Technical Note
6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Check the continuity of the following connection:
Connection code 47Z between components 645 and 653.
If the connection is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
If the connection is correct, replace the display (component code 653)
(see MR 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact Techline.
NOIf the vehicle is fitted with an external
temperature sensor, check that the
configuration CF029 “External
temperature sensor” displays “With”.
If the vehicle is not fitted with an external
temperature sensor, it is normal that the
external temperature is not displayed.
AFTER REPAIRCarry out another fault finding check on the system.
UCH_V44_AC110

87B -165
MR-413-X44-87B000$864.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints87B
*RF: radio frequencyWIPERS85A
NO REAR SCREEN WIPING ALP 13
THE REAR SCREEN WIPER BLADE STOPS IN
AN INCORRECT POSITIONALP 14
NO WINDSCREEN WIPER FUNCTION WHEN THE STALK IS MANIPULATED ALP 15
THE WINDSCREEN WIPER BLADES STOP IN
AN INCORRECT POSITIONALP 16
NO FRONT AND REAR SCREEN WASHER ALP 17
NO WIPING WHEN IT RAINS ALP 18
NO CHANGE IN WIPING SPEED AFTER
ACTIVATING THE WIPER INTERMITTENT SPEED RINGALP 19
ACCESS/SAFETY82D
RF* CONTROL LOCKING/UNLOCKING
FAULT FAULTALP 20
TAILGATE OPENING PROBLEM ALP 21
CENTRAL LOCKING/UNLOCKING FAULT
ON ONE OR MORE DOOR(S)ALP 22
RENAULT ANTI-INTRUDER
DEVICE FUNCTION FAULTALP 23
OPENING FROM THE INSIDE NOT POSSIBLE ALP 24
PROTECTION - STARTING82D
STARTING PROTECTION (VEHICLE DOES NOT START
WHEN IGNITION KEY TURNED)ALP 25

87B -176
MR-413-X44-87B000$912.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
ALP 33 No external temperature display
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the temperature display works, use AC110 Temperature display.
Read configuration LC002 External
temperature sensor.
Is the configuration YES?
YES
Check that LC067 Temperature display is With. Otherwise perform
CF171 Temperature display.
Check the condition and connection of the PE2 40-track connector in the
UCH (component code 645) (tabs bent, broken, etc.).
If the connector is faulty and there is a repair method (see Te chnical Note
6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Check the continuity of the following connection:
Connection code 47Z between components 645 and 653.
If the connection is faulty and there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
If the connection is correct, replace the display. (See MR 411 Mechanical,
86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact the Techline.
NOThe vehicle is not equipped with the
External temperature sensor function.
It is normal for the external temperature
not to be displayed.
UCH_V44_ALP33