technical specifications RENAULT TWINGO 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD User Guide

87B -108
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
LIGHTING STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSHAZARD LIGHTS
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
Check that fuses F13 (30 A), F15 (5 A) (without automatic headlighting) or F15 (15A) (with automatic
headlighting) is sound and correctly fitted in the passenger compartment fuse and relay box
(component code 1016).
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET081

87B -111
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET082
REAR FOG LIGHTS REQUEST
NOTESNo faults should be present or stored.
Note:
The signal can only be interpreted if the function is managed by the UCH
(vehicle equipped with one-touch fog light control)
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) on the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised or
broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
Check for + 12 V (when rear fog lights are requested) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MG on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET082

87B-114
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET083
ET084
LEFT-HAND INDICATOR REQUEST
RIGHT-HAND INDICATOR REQUEST
NOTESNo faults should be present or stored.
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check that fuses F13 (30A) and F15 (5 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET083 / UCH_V44_ET084

87B-116
MR-413-X44-87B000$624.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET085
HAZARD WARNING LIGHTS BUTTON
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC018 Hazard warning lights switched on by ABS is definitely With.
Otherwise, run CF024 Illumination of hazard warning lights by ABS.
SPECIFICATIONSDEPRESSED
RELEASED
Check the presence and condition of fuse F42 (10 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the central door locking/warning switch connector (component code 1391)
(tabs broken, bent, oxidised).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection LPD of the locking/warning switch (component code 1391).
Check for earth on connection MAN of the locking/warning switch (component code 1391).
Check for + 12 V on connection 64D (when there is a hazard warning lights request) on components 255, 267 and
172.
Check for earth on components 255, 267 and 172 (indicator lights).
Check for + 12 V on connection 64C (when there is a hazard warning lights request) of components 256, 268 and
173 (indicator lights). Check for earth on components 256, 268 and 173.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET085
MR-413-X44-87B000$624.mif
UCH
Vdiag No.: 44

87B-118
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET087
ONE-TOUCH WINDOW CONTROL/SUNROOF AUTHORISATION.
NOTESThere must be no present or stored faults.
Check the following configuration:
–Check that LC070 One-touch windows/SR* is With. Otherwise, perform CF173
One-touch windows/SR.
Authorisation by the UCH of the one-touch window winder and/or sunroof motor
function is present under the following conditions:
–+ ACCESSORIES FEED,
–+ AFTER IGNITION FEED,
–when the engine is running.
SPECIFICATIONSPRESENT
ABSENT
Check the condition and connection of the PE2 24-track UCH connector, (component code 645) (tabs bent,
broken, oxidised).
Check the condition and connection of the driver's electric window motor 6-track connector (component 203)
(tabs bent, broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If there is an electric sunroof, check that fuse F26 (20 A) is sound and correctly fitted in the passenger
compartment fuse and relay box (component code 1016).
Check the condition and connection of the connectors for component 1512.
With an electric sunroof, check the condition and connection of 4-track connector 339 in the A-pillar and the
sunroof computer 12-track connector (tabs bent, broken, oxidised).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET087

87B -120
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
Windscreen wiper fault:
Check the presence and condition of fuse F2 (15 A) on the passenger compartment fuse and relay box (component
code 1016).
Replace the fuse if necessary.ET096
WIPER STALK INTERMITTENT SPEED RING POSITION
NOTESThere must be no present or stored faults.
Check the following configurations:
–Check that LC094 Wiper intermittent speed ring displays With. If not, run
CF191 Wiper intermittent speed ring.
–Check that LC096 Automatic wiper function displays With. If not, run CF194
Automatic wiper function.
–Check that LC095 Automatic headlight function displays "With". If not, run
CF193 Automatic headlight function.
SPECIFICATIONSINACTIVE
1
2
3
4
5
Check the condition and connection of the 3-track windscreen wiper motor connector (component code 212)
(tabs bent, broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET096

87B -122
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET097
REAR SCREEN WIPER PARK POSITION
NOTESThere must be no present or stored faults.
SPECIFICATIONSYES
NO
Check the presence and condition of fuse F36 (15 A) on the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track rear screen wiper motor connector (component 211) (tabs
bent, broken, oxidised).
Activate the rear screen wiper with the switch stalk (component code 209) or with AC007 "Rear screen wiper",
check for + 12 V on connection 36A of the rear screen wiper motor connector (component code 211).
Check that the earth on connection MYH of the rear screen wiper motor connector (component code 211) is
in perfect condition.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the PE1 40-track UCH connector, (component code 645) (tabs bent,
broken, oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET097

87B -125
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET111
FRONT FOG LIGHTS REQUEST
NOTESThere must be no present or stored faults.
Check that the LC015 Front fog lights is definitely With. Otherwise, use command
CF021 Front fog lights.
Note:
The signal can only be interpreted if the function is managed by the UCH (component
code 645) (vehicle equipped with one-touch fog light control).
SPECIFICATIONSPRESENT
ABSENT
Use AC008 Front fog lights to check that the front fog lights operate correctly.
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), in the passenger compartment fuse
and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the front fog light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the PE2 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
Check the condition and connection of the control stalk connector (component code 209) (tabs bent, oxidised,
broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V (when there is a rear fog lights request) on connection 8B of components 176 and 177. Check
for earth on connection MAR of component 176 and connection MAS of component 177.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET111

87B -128
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET114
ET115
WIPER REQUEST BY RAIN SENSOR
LIGHT ACTIVATION REQUEST BY LIGHT SENSOR
NOTESThere must be no present or stored faults.
Make sure that the vehicle is fitted with the rain and light sensor.
The status should change to LOW SPEED or HIGH SPEED if there is water on the
windscreen where the sensor is positioned.
The status should change to PRESENT when the light intensity requires the lights to
be switched on with the engine running.
Make sure that the other positions of the wiper control are working properly
Check the following configurations:
–Check that LC008 Daytime running lights is "With". Otherwise run CF014
Daytime running lights.
–Check that LC044 Rain/light sensor displays "Present". If not, run CF035 Rain/
light sensor.
–Check that LC095 Automatic headlight function displays "With". If not, run
CF193 Automatic headlight function.
–Check that LC096 Automatic wiper function displays With. If not, run CF194
Automatic wiper function.
SPECIFICATIONSET114: ABSENT/LOW SPEED/HIGH SPEED
ET115: PRESENT/ABSENT
Conditions:
Check that the switch stalk (component code 209) is in the intermittent position so that automatic operation can
be activated.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, perform the following cycle twice to activate the automatic headlight
function: Switch stalk (component code 209) OFF → Σωιτχη σταλκ (χοµπονεντ χοδε 209) to side lights ON
position.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET114 / UCH_V44_ET115

87B -132
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET185
KEY CODE RECEIVED
NOTESThere must be no present or stored faults.
Apply the checks only if the status is NO with the ignition on.
SPECIFICATIONSYES
NO
Check that there are no powerful electromagnetic wave sources (CB (Citizen Band), mobile phone in close
proximity to the transponder ring).
Switch the ignition off and then on again.
Check that fuse F8 (15 A) is sound and correctly fitted in the passenger compartment fuse and relay box.
Replace the fuse if necessary.
Try the vehicle's second key.
If the status changes to YES, replace the first key and program the keys using command SC015 Key allocation.
This status tells you whether the UCH has received the immobiliser code from the key.
If the status remains NO, check the connection between the transponder ring (component code 1618) and the
UCH (component code 645).
Check the + 12 V feed on connection AP43 of component 1618.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the earth on track 2 of the transponder ring is in perfect condition.
Check the insulation, the continuity and the absence of interference resistance on the following
connections:
●Connection code AP43 between components 1016 and 1618.
●Connection code 80X between components 645 and 1618.
●Connection code 80Y between components 645 and 1618.
●Connection code NAM between component 1618 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET185