lock RENAULT TWINGO 2009 2.G Engine Diesel Injection Owner's Manual

13B-150
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
*RCH = Passenger Compartment Heating Resistors
ET111SET NUMBER OF PASSENGER COMPARTMENT HEATING RESISTORS
STATUS DEFINITIONThis status indicates that the injection computer is blocking any change to the number
of passenger compartment air heating resistors active (active ones are not cut off, but
no more can be added). This freeze in the number of heating resistors is in response to
vehicle needs (availability of power, need for torque etc.).
Conformity check: Engine stopped and ignition on, or engine running and engine coolant temperature
> 80
°C
YESDepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer sets the number of activated passenger
compartment heating resistors (no more or no fewer than required).
Status ET111 becomes YES when the number of activated passenger compartment
heating resistors is set by the injection computer.
NODepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer sets the number of activated passenger
compartment heating resistors (no more or no fewer than required). Status ET111
becomes NO if the number of passenger compartment heating resistors engaged can
be freely controlled by the UCH.
DCM1.2_V48_ET111/DCM1.2_V4C_ET111/DCM1.2_V50_ET111/DCM1.2_V54_ET111/DCM1.2_V58_ET111/DCM1.2_V5C_ET111

13B-151
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
*RCH = Passenger Compartment Heating Resistors
ET112PASSENGER COMPARTMENT HEATING RESISTOR CUT-OFF
STATUS DEFINITIONThis status indicates that the injection computer is blocking activation of all passenger
compartment air heating resistors due to vehicle needs (availability of power, need for
torque, injection defect mode or heating and ventilation etc.).
Conformity check: Engine stopped and ignition on, or engine running and engine coolant temperature
> 80
°C
YESDepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes YES when the passenger compartment heating resistors are cut
off by the injection computer.
NODepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes NO when the passenger compartment heating resistors can be
freely controlled by the UCH.
DCM1.2_V48_ET112/DCM1.2_V4C_ET112/DCM1.2_V50_ET112/DCM1.2_V54_ET112/DCM1.2_V58_ET112/DCM1.2_V5C_ET112

13B-154
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS DEFINITIONThis status varies according to engine specifications.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control/speed limiter function, due to a driver
request or the external environment (e.g. STATUS 1).
IMPORTANT
Clear the fault memory by running command RZ001 "Fault memory" to reset this status to "NONE".
Conformity check: Engine stopped, ignition on or engine running.
WITHOUTThis status is present on the diagnostic tool when:
–the computer has been reinitialised.
–the computer has been reprogrammed.
STATUS 1Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and traction control is requested.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-lock
braking system).
DCM1.2_V48_ET415/DCM1.2_V4C_ET415/DCM1.2_V50_ET415/DCM1.2_V54_ET415/DCM1.2_V58_ET415/DCM1.2_V5C_ET415

13B-158
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V6 MR-413-X44-13B000$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET415
CONTINUED 4
STATUS 8Automatic gearbox in defect mode.
Status ET415 becomes STATUS 8 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the automatic gearbox is in
defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test (see 88B, Multiplexing), then run fault finding on the
automatic gearbox computer.
Deal with any present or stored faults (see 23A, Automatic gearbox).
Clear the fault memory of the automatic gearbox computer by applying command RZ001
Fault memory.
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If the specification STATUS 8 is still present, contact Techline.
STATUS 9Vehicle speed monitoring
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Test the multiplex network (see 88B, Multiplexing), then run fault finding on the ABS
computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system).
Reinitialise status ET415 on the injection computer by running command RZ001
"Fault memory".
If the specification STATUS 9 is still present, contact Techline.

13B-189
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR089VEHICLE SPEED
PARAMETER
DEFINITIONThis parameter indicates the vehicle speed in mph (km/h).
NOTESSpecial notes:
This parameter is transmitted by the ABS computer or by the wheel speed computer.
This signal is transmitted to the injection on the multiplex network.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing)
Then a complete fault finding procedure of the ABS computer (see 38C, Antilock braking system) or VSU
(see 38G, Wheel speed computer).
DCM1.2_V48_PR089/DCM1.2_V4C_PR089/DCM1.2_V50_PR089/DCM1.2_V54_PR089/DCM1.2_V58_PR089/DCM1.2_V5C_PR089

13B-193
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault
memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$170.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
PR132
CONTINUED
Sensor electrical conformity
Test the air inlet circuit (from the air filter inlet to the inlet manifold tracts, run test 5 Inlet circuit check):
–air filter unit inlet not blocked and filter not clogged,
–oil vapour recirculation circuit connected correctly,
–low and high pressure air circuit sealed and not obstructed: ducts, mounting clamps present and tightened,
turbocharging pressure sensor fitted, exchanger, etc., run TEST 1 Low pressure circuit check and TEST 7
High pressure circuit sealing check
–check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
–3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
–3FB (or 3FB3) of component 799.
Check the continuity and absence of interference resistance of the following connections:
–3DV,
–3DW, between components 120 and 799.
Flowmeter connected, vehicle ignition on and engine stopped:
Measure the voltage between connections 3DW and 3DV of component 799.
If the voltage is not between 0.3 V and 0.7 V, replace the air flowmeter, component code 799 (see MR 364 (Mégane
II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2),
Mechanical, 12A, Fuel Mixture, Air Flowmeter: Removal - Refitting).

13B-209V6 MR-413-X44-13B000$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 2 Electrical circuit check
Check the battery charge and that the alternator
is operating correctly (see 87B, Passenger
compartment connection unit for the New
Twingo or see 87G, Engine compartment
connection unit for Clio III, Modus, Mégane II,
Scénic II and Kangoo 2).
Is the charging circuit in good order? Carry out the necessary repairs.
Check the fuses.
Are the fuses correct? Carry out the necessary repairs.
Check that the injection locking relay is operating
correctly.
Is the injection locking relay working properly? Carry out the necessary repairs.
Check the engine earths.
Are the engine earths correct? Carry out the necessary repairs.
The electrical circuit is in good order.
NO
YES
NO
YES
NO
YES
NO
DCM1.2_V48_TEST2/DCM1.2_V4C_TEST2/DCM1.2_V50_TEST2/DCM1.2_V54_TEST2/DCM1.2_V58_TEST2/DCM1.2_V5C_TEST2

13B-211V6 MR-413-X44-13B000$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 5 Inlet circuit check
Check for air leaking in or out.
Is air leaking in or out? Carry out the necessary repairs.
Check the condition of the air filter.
Is the air filter correct?Replace the air filter (see MR 364 (Mégane II),
MR 370 (Scénic II), MR 385 (Modus), MR 392
(Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 12A, Fuel mixture,
Air filter: Removal - Refitting).
Check that the inlet manifold is not obstructed
(clogged).
Is the inlet manifold blocked? Clean the inlet manifold.
Air system in good order.
YES
NO
NO
YES
YES
NO
DCM1.2_V48_TEST5/DCM1.2_V4C_TEST5/DCM1.2_V50_TEST5/DCM1.2_V54_TEST5/DCM1.2_V58_TEST5/DCM1.2_V5C_TEST5

13B-218V6 MR-413-X44-13B000$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 9 Diesel filter check
Check the conformity of the diesel filter.
Is the diesel filter in order?Replace the air filter with an original part
(see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392
(Clio III), MR 411 (New Twingo), MR 417
(Kangoo 2), Mechanical, 13A, Fuel
mixture, Air filter: Removal - Refitting).
–Switch off the ignition and analyse the diesel fuel in the diesel filter.
–Disconnect the diesel supply and return hoses from the filter.
–Block the filter inlets and outlets straight away with appropriate plugs.
–Remove the filter from its holder and shake it firmly while holding the caps in place. Tap the edge of the filter with
a screwdriver handle to detach any contamination. Empty the contents of the filter into a glass container by lifting
a protective plug, then loosening and completely removing the bleed screw.
Are black particles present on the bottom of the container?
Pass a magnet beneath the container to collect
all the metal particles. Take the magnet away
from the container.Diesel filter in good order.
Do the particles collected using the magnet
cover a surface area greater than 1 cm
2?
Replace the entire
injection system.Diesel filter in good
order.
NO
YES
YESNO
YESNO
DCM1.2_V48_TEST9/DCM1.2_V4C_TEST9/DCM1.2_V50_TEST9/DCM1.2_V54_TEST9/DCM1.2_V58_TEST9/DCM1.2_V5C_TEST9

13B-221V6 MR-413-X44-13B000$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 10
CONTINUED 2
Visual inspection of the electrical connector of the solenoid valve
Switch off the engine.
Note:
The requested checks are only visual.
1. Check that the connector is correctly connected and locked.
2. Check the absence of damage to the electric wires where they leave the insulation.
Disconnect the connector to continue the checks.
3. Check the absence of thermal damage to the unit and mechanical damage to the lock.
4. Check the absence of deformations of the contacts (clips and tabs).
5. Check the sealing of the connector.
Do the visual inspections show any damage?
Refer to Technical Note 6015A, Repairing electrical wiring.
B
NO
YES
A
C