check engine RENAULT TWINGO 2009 2.G Heating And Air Conditioning - Manual Air Conditioning User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 63
Page 31 of 63
62C-31
MR-413-X44-62C000$637_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Conformity check62C
SUB-FUNCTION: HEATING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine at idle speed, AIR CONDITIONING OPERATING
(air conditioning compressor engaged).
ComputerParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (continued)
(see 87B,
Passenger
compartment
connection unit)ET239:Ignition switch
position+ after ignition feedIn the event of a fault, refer to the
interpretation of this status.
PR025:Engine speed800 rpm ± 50 rpmIn the event of a fault, see the
interpretation of this
parameter.
PR024:Engine coolant
temperatureX = engine coolant
temperatureIn the event of a fault, see the
interpretation of this
parameter.
ET015:Passenger
compartment
blowerACTIVE
(according to test
conditions: see Notes).In the event of a fault, refer to the
interpretation of this status.
Note: This status only operates
for manual air conditioning and
heating versions.
PR001:Battery voltage12.5 V < X < 14.4 VIn the event of a fault, see the
interpretation of this
parameter.
If the fault is still present, carry
out fault finding on the charging
circuit (see MR 411 Mechanical,
16A, Starting - Charging).
PR002:Exterior
temperature
(depending on
the version)X = exterior
temperature ±± ± ±
5 ˚C
(invalid value: 215 ˚C).In the event of a fault, see the
interpretation of this
parameter.
Page 32 of 63
62C-32
MR-413-X44-62C000$637_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Conformity check62C
SUB-FUNCTION: HEATING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine at idle speed, AIR CONDITIONING OPERATING
(air conditioning compressor engaged).
ComputerParameter or Status
checked or ActionDisplay and Notes Fault finding
Injection (see 13B,
Diesel injection or
17B, Petrol
injection)PR064:Coolant
temperatureX = engine coolant
temperatureIn the event of a fault, see the
interpretation of this
parameter.
ET111:RCH number setYES or NO
Note: Depending on the
requirements of the
injection system (power
requirement, torque
reduction, etc.), the
injection computer sets
the controlled
passenger compartment
heating resistor stage
number (no more,
no less)In the event of a fault, refer to the
interpretation of this status.
ET112:RCH cut-offYES or NO
Note: Depending on the
requirements of the
injection system (power
requirement, torque
reduction, etc.), the
injection computer sets
the controlled
passenger compartment
heating resistor stage
number (no more,
no less)In the event of a fault, refer to the
interpretation of this status.
Page 33 of 63
62C-33
MR-413-X44-62C000$637_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Conformity check62C
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine at idle speed, AIR CONDITIONING OPERATING
(air conditioning compressor engaged).
ComputerParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)ET028:Heated rear
screen buttonPRESSED if the heated
rear screen key on the
air conditioning control
panel is pressed.
RELEASED otherwise.In the event of a fault, refer to the
interpretation of this status.
ET029:Air conditioning
buttonPRESSED if the AC
button on the air
conditioning control
panel is pressed.In the event of a fault, refer to the
interpretation of this status.
ET015:Passenger
compartment
blowerACTIVE
(according to test
conditions: see Notes).In the event of a fault, refer to the
interpretation of this status.
Page 48 of 63
62C-48
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
Preliminary cold loop efficiency test
ALP 8 No cold air
NOTESConsult this customer complaint after a full check with the diagnostic tool
(fault reading and configuration checks).
Check that the engine speed is greater than 750 rpm and that the exterior
temperature is above 3 ˚C.
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, New Twingo.
With engine running, air conditioning in maximum
cold position and maximum ventilation speed. After
10 minutes, is the high pressure pipe at the
compressor outlet hot, and the low pressure pipe at
the evaporator outlet cold and iced up?
NO
Check the cleanliness of the condenser. Touch the
pipes: are they warmer at the inlet than the outlet?
YES
Is the dehydrator reservoir pipe hot at the inlet and
outlet?
YES
Is the expansion valve pipe hot at the inlet and
outlet?
NO
Is the evaporator pipe hot at the inlet and outlet?
NO
1
YES2
NOReplace the condenser (see MR 411
Mechanical, 62A, Air conditioning,
Condenser: Removal - Refitting).
NOReplace the dehydrator reservoir (see MR
411 Mechanical, 62A, Air conditioning,
Dehydrator reservoir: Removal -
Refitting).
YESReplace the expansion valve (see MR 411
Mechanical, 62A, Air conditioning,
Expansion valve: Removal - Refitting).
YESReplace the evaporator (see MR 411
Mechanical, 62A, Air conditioning,
Evaporator: Removal - Refitting).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 49 of 63
62C-49
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 1
1
Using the diagnostic tool statuses and parameters
screen (UCH heating sub-function), check that the
temperature signals are consistent (no sensor
deviations resulting in incorrect measurement).
–Use statuses PR002 Exterior temperature and
PR024 Engine coolant temperature.
Are the temperature signals consistent?
YES
Start the engine and switch on the air conditioning by
pressing the AC button (with a request for maximum
cold temperature and the passenger compartment
blower running).
2
Display the following status in the “User selection”
sub-function screen:
ET029 Air conditioning button should be
PRESSED.
Note:
The status indicates if the signal for the AC button
pressed on the control panel is read by the UCH
correctly.
Does status ET029 display PRESSED?
YES
NOCarry out a conformity check:
–For the coolant temperature sensor,
see 13B, Diesel injection, Fault
summary table or 17B Petrol
injection, Fault summary table.
–For the exterior temperature sensor,
see 87B, Passenger compartment
connection unit, Fault summary
table.
Replace any faulty components.
NOContinuity fault on connection 38LP.
Using an ohmmeter, carry out a continuity
test on connection 38LP between
components 319 and 645. If there is a
procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring,
otherwise replace the wiring.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 50 of 63
62C-50
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 2
With the engine running at idle speed, use the
diagnostic tool to check that UCH does in fact
send the start air conditioning request to the
injection computer. Status ET030 Air conditioning
request 2 should display ACTIVE.
Is status ET030 “ACTIVE”?
YES
Using the diagnostic tool (injection cold loop sub-
function screen), display the following statuses:
- ET004 Air conditioning authorised,
- ET088 Compressor activation request.
Is status ET004 “YES” and status ET088
“ACTIVE”
NO
Check that the injection computer is correctly configured. Status ET079 CLIMATE CONTROL PRESENT should
display YES (cold loop sub-function screen).
Is status ET079 YES?
YESNOCheck that the UCH is correctly configured by
viewing the configuration reading LC013 Type
of air conditioning.
Should be “Manual air conditioning”
Reconfigure the UCH if necessary.
Check that the UCH is receiving the engine
operating status and passenger compartment
blower signals correctly (for manual air
conditioning). In the Cold Loop sub-function
screen, status ET142 “Engine operating
phase” should display “RUNNING” and status
ET015 “Passenger compartment blower”
should display “ACTIVE” and parameter
PR024 “Exterior temperature” should be >
3˚C.
If the parameter and statuses are not correct,
carry out fault finding on the multiplex network
and UCH (interpretation of status ET015,
ET142 and parameter PR024).
YES
NO
Interpretation fault for status ET079, see
conformity check, cold loop sub-function:
–13B, Diesel injection,
–17B, Petrol injection.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 51 of 63
62C-51
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 3
Carry out fault finding on the injection system to ensure that no fault is present (if faults are displayed by the
injection computer, engagement of the air conditioning may be inhibited). If there are present or stored faults,
carry out the necessary repairs (see 13B, Diesel injection or 17B, Petrol injection).
Check that the refrigerant fluid pressure is correct (neither too low nor too high) using the PR037 Refrigerant
fluid pressure parameter (see Conformity check, Cold loop sub-function).
Check that the engine cooling fan assembly is at
speed 1 by viewing the following status on the cold
loop sub-function screen:
–Status ET022 Low-speed fan assembly request
should display ACTIVE.
Note:
These statuses are not displayed by all types of
injection (see Conformity check, Cold loop sub-
function).
Does the engine cooling fan operate at low speed?
YES
NOUsing the diagnostic tool, run
command AC154 Low speed fan
assembly relay.
Does the engine cooling fan operate
at low speed?
NO YES
Connector of component 321 disconnected. Connect a
test light between connection 49L of component 321
and the chassis earth and run command AC154 Low
speed fan assembly relay.
Does the test light illuminate?
YES NO
Measure the resistance of component 321, between
connections 49L and 49B of component 321. If the
resistance measured is infinite, replace the fan assembly
resistor (component 321).
Carry out fault
finding on the
injection system
(sub-function: cold
loop and engine
cooling for low
speed fan assembly
activation).
D
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 53 of 63
62C-53
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 5
Check the air conditioning compressor belt tension
(see Technical Note 3786A, Engine and
peripherals, 10A, Belt tension setting tool Hz
measurement: tension values).
Is the tension correct?
YES
With the engine stopped, use the diagnostic tool to
run command AC180 Air conditioning
compressor relay (injection command mode
menu).
Does the compressor clutch jam?
YES
E
NOReplace the belt (see MR 411
Mechanical, 11A, Top and front of
engine, Accessories belt:
Removal - Refitting).
NO
YESConnect a test light between connections 38R
and MAS of component 171 and run
command AC180 Air conditioning
compressor relay.
Does the test light illuminate?
NO
Connect a test light between connection 38R
of component 171 and the chassis earth, then
run command AC180 Air conditioning
compressor relay.
Does the test light illuminate?
YES
Earth fault on component 171.
If there is a repair procedure
(see Technical Note 6015A,
Repairing electrical wiring,
Wiring: Precautions for
repair), repair the wiring,
otherwise replace the wiring.
Check the condition of the
diode (component 322).
Replace the diode if it is faulty.
Replace the air conditioning
clutch (component 171) if
possible, otherwise replace
the compressor (see MR 411
Mechanical, 62A, Air
conditioning, Compressor:
Removal - Refitting).
NO
F
Page 55 of 63
62C-55
MR-413-X44-62C000$819_eng.mif
V1
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts62C
ALP 8
CONTINUED 7
2
With the engine warm and passenger compartment
ventilation operating, vary the position of the mixing
flap from the maximum hot position to the maximum
cold position and check subjectively that there is a
difference in temperature.
Is a difference in temperature noted?
YES
E
NOCheck the condition and routing of the mixing
flap control cable. Eliminate any constraints it
may have such as kinks, restriction by plastic
clips, etc.
Replace the lead if necessary. Unclip the
cable from the side of the heating/air
conditioning unit and check the stiffness of
movement of each component: control
button and flap control on the air distribution
unit. Check that there is no mechanical fault
with the mixing flap (flap jammed inside the
unit, etc.). Carry out any necessary repairs.
Is the fault still present?
YES NO
End of fault finding
procedure.
Check the cold loop by checking the condition of the pipes and ensuring that the air conditioning system does not
have any refrigerant leaks (see Technical Note 6001A, Air conditioning, 62A, Air conditioning, Air
conditioning: Check). Repair the faulty pipes or components.
Top up the refrigerant (see MR 411 Mechanical, 62A, Air conditioning, Refrigerant circuit: Draining - Filling).
Is the fault still present?
NO YES
End of fault finding procedure. Replace the air conditioning compressor.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 56 of 63
62C-56
MR-413-X44-62C000$910_eng.mif
V1
62C
MANUAL AIR CONDITIONING
Fault finding - Fault finding charts
ALP 9 Too much cold air
NOTESConsult this customer complaint after a full check with the diagnostic tool (fault reading and
configuration checks).
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, New Twingo.
With the engine at idle speed and the heating and air conditioning off (AC button not pressed), check that the air conditioning
compressor clutch is not engaged.
Is the air conditioning compressor clutch engaged? NO
YES
With the engine stopped, check that the compressor clutch electric control operates correctly, using the diagnostic tool to run
command AC180 Air conditioning compressor relay (injection command mode menu).
–During the command, connection 38R of component 171 must be supplied with + 12 V.
–After the command, connection 38R of component 171 must no longer be supplied with + 12 V.
Is the connection still supplied with + 12 V after the command?
YES NO
Check the continuity and insulation from + 12 V of
connection 38R between components 171 and 584.Check that the air conditioning compressor clutch is not
jammed (mechanical fault).
Is the connection OK? Is the clutch still engaged?
NO YES YES
If there is a repair procedure (see
Technical Note 6015A, Repairing
electrical wiring, W iring:
Precautions for repair), repair the
wiring, otherwise replace it.With the vehicle ignition of f, check that
the compressor clutch relay is not
“jammed”, by checking the continuity
between connection 38R and
connection AP3 of component 584.
Is the continuity present?
NO
Apply the fault finding procedure for command
AC180 Air conditioning compressor relay
(see 13B Diesel injection or 17B Petrol
injection).
Is the fault still present?
Replace the air conditioning
compressor (see MR 411,
Mechanical, 62A, Air conditioning,
Compressor: Removal - Refitting).
YESReplace the air
conditioning
compressor clutch
relay.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
MR-413-X44-62C000$910_eng.mif