belt RENAULT TWINGO 2012 2.G Owner's Manual

JauneNoirNoir texte
1.33
ENG_UD24497_2
Sécurité enfants : installation du siège enfant (X44 - Renault\
)
ENG_NU_952-4_X44_Renault_1
ChILD sAFETY : Fitting a child seat (2/4)
R IsK O F D E AT h O R
s ERIOU s INJURY: before
installing a rear-facing child
seat in the front passen -
ger seat, make sure the air bag has
been deactivated (refer to Section
1 “Child safety: front passenger air
bag deactivation/activation”).
Forward facing harness seats are
only permitted if they are installed
using an ISOFIX fitting and without
a seat belt.Child seat attached using the belt
¬ Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
− Seat which only allows a rear-
facing seat with “Universal” approval
to be attached with a seat belt.
³ Check the status of the air bag
before fitting a child seat or allowing a
passenger to use the seat.
Child seat attached using the IsOFIX
mounting
ü Seat which allows an ISOFIX
child seat to be fitted.
± The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
Universal approval to be fitted. The an-
chorage points are located in the lug -
gage compartment and are visible.
The size of the ISOFIX child seat is in-
dicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: cots in group 0 (less than
10 kg).
Using a child safety system which is not approved for this vehicle will not
correctly protect the baby or child. They risk serious or even fatal injury.

1.34
ENG_UD24497_2
Sécurité enfants : installation du siège enfant (X44 - Renault\
)
ENG_NU_952-4_X44_Renault_1
Jaune NoirNoir texte
Type of child seat Weight of
the child seat size
IsOFIX passenger front
seat (1) (2) Rear side seats
right left
Carrycot fitted across the vehi- cle
Group 0 < 10 kg
F XU - IL (4) U (4)
shell seat/rear-facing seat
Groups 0, 0 + or 1 < 13 kg and
9 kg to 18 kg D, E
U - IL U - IL (5) U (5)
Rear-facing seat
Groups 0 + and 1 < 13 kg and
9 kg to 18 kg C
U - IL U (3)U (3)
Forward-facing seat
Group 1 9 kg to 18 kg
A, B, B1 IL - IUFU - IUF - IL (6) U (6)
Booster cushion
Group 2 or 3 15 kg to 36 kg
–X U (6)U (6)
(1) RIsK OF DEATh OR sERIOUs INJURY: before installing a rear-facing child seat on the front passenger seat,
check that the air bag has been deactivated (refer to Section 1 “Child safety: deactivating/activating the front passen -
ger air bag”).
Forward facing harness seats are only permitted if they are installed us\
ing an ISOFIX fitting and without a seat belt.
ChILD sAFETY : Fitting a child seat (3/4)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.

JauneNoirNoir texte
1.35
ENG_UD24497_2
Sécurité enfants : installation du siège enfant (X44 - Renault\
)
ENG_NU_952-4_X44_Renault_1
X = Seat not suitable for fitting child seats.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(2) Before fitting a rear-facing child seat: raise the seat to the maximum and position it as far back as possible, tilting the seatback
slightly (approximately 25°).
(3) It is recommended to position the rear seat as far back as possible ensuring, if required, that the floor support of the child seat
is resting on the floor in accordance with the child seat instructions.
(4) A carrycot can be installed across the vehicle and will take up two seats. Position the child with his or her feet nearest the door.
(5) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat or seats in front as
far as they will go, although without allowing them to come into contact\
with the child seat.
(6) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
height of the headrest or remove it if necessary; do not push the seat in front of the child more than halfway back on its runners
and do not recline the seatback more than 25°.
ChILD sAFETY : Fitting a child seat (4/4)

1.36
ENG_UD29224_6
sécurité enfants : désactivation/activation airbag (X44 - Rena\
ult)
ENG_NU_952-4_X44_Renault_1
Jaune NoirNoir texte
Deactivating/activating the front passenger airbag
Deactivating the front
passenger airbags
(on equipped vehicles)
In order to fit a child seat to the front
passenger seat when this is allowed,
you must deactivate the front passen-
ger seat additional restraint devices
(side airbags (depending on vehicle),
front airbags, etc.). To deactivate the restraint devices
supplementary to the front passen
-
ger seat belt: switch off the ignition,
press and turn lock 1 to the OFF posi-
tion. The airbag is deactivated.
With the ignition on, it is essential to
check that warning light 2 is lit on the
instrument panel.
This warning light remains lit to con-
firm that you can fit a child seat, as
the passenger air bag has been de -
activated.
1
ChILD sAFETY : deactivating/activating the front passenger airbag (1/3)
2
The passenger air bag must
only be deactivated or acti-
vated with the ignition off.
If it is interfered with when
the vehicle is being driven, indicator
lights
å and © will come
on.
Switch the ignition off then on again
to reset the air bag in accordance
with the lock.

1.38
ENG_UD29224_6
sécurité enfants : désactivation/activation airbag (X44 - Rena\
ult)
ENG_NU_952-4_X44_Renault_1
Activating the front
passenger air bags
You should reactivate the air bag as
soon as you remove the child seat from
the front passenger seat to ensure the
protection of the front passenger in the
event of an impact.
To reactivate the restraint devices
supplementary to the front passen -
ger seat belt: switch off the ignition,
press and turn lock 1 to the ON posi -
tion.
With the ignition on, check that the
warning light 2 goes out.
The front passenger seat belt additional
restraint systems are activated.
Operating faults
If the front passenger air bag activa -
tion/deactivation system is faulty, child
seats must NOT be fitted to the front
seat.
Allowing any other passenger to sit in
that seat is not recommended.
Contact your approved dealer as soon
as possible.
The passenger air bag must
only be deactivated or acti-
vated with the ignition off.
If it is interfered with when
the vehicle is being driven, indicator
lights
å and © will come
on.
Switch the ignition off then on again
to reset the air bag in accordance
with the lock.
2
ChILD sAFETY : deactivating/activating the front passenger airbag (3/3)
1

1.46
ENG_UD30823_8
Tableau de bord : témoins lumineux (X44 - Renault)
ENG_NU_952-4_X44_Renault_1
Jaune NoirNoir texte
2
Not used

ßFront seat belt reminder
warning light
This comes on when the engine is
started; if the driver or front passenger
seat belt is not fastened (if this seat is
occupied) and the vehicle has reached
approximately 10 mph (15 km/h), it
flashes and a beep sounds for around
2 minutes.
Note: an object placed on the passen-
ger seat base may activate the warning
light in some cases.
ãp assenger air bag warning
light OFF
It lights up when the ignition is switched
on and goes out after a few seconds,
unless the passenger air bag is deacti-
vated (refer to Section 1: “Deactivating
the front passenger air bags”).
INsTRUMENT p ANEL: warning lights (3/4)
åAir bag warning light
This lights up when the ignition
is switched on and goes out after a few
seconds.
If it remains lit or comes on when the
engine is running, it indicates a system
fault.
Contact your approved dealer as soon
as possible.
xAnti-lock braking warning
light
This lights up when the ignition is
switched on and goes out after a few
seconds.
If it does not go out when the ignition is
switched on, or lights up when driving,
there is a fault with the ABS.
Braking will then be as normal, without
the ABS.
Contact an approved dealer as soon as
possible.
ûsTOp light
It switches off a few seconds
after the ignition is switched on, if it
does not light up, consult an approved
dealer. It may light up at the same time
as other warning lights, together with
a beep. It indicates that it is essential
to stop immediately (as soon as traffic
conditions allow). Contact an approved
dealer.
The presence and operation of the warning lights DEpEND ON ThE EQUIpMENT AND COUNTRY.

rear seatsfunctions ......................................... (up to the end of the DU)
adjusting the seats ................................ (up to the end of the DU)
rear seats .............................................. (up to the end of the DU)
3.31
ENG_UD24499_5
Sièges arrière : fonctionnalités (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Rear seats: functions
REAR SEATS: functions
To fold down the rear seatsThe seats can be folded down in order
to transport large objects:
From the front, lower the headrest.
From the rear, lift handle 2 to fold down
the seatback, lower bar 1 of the seat
concerned and move it forwards fully.
Lift the controls 3 located either side
of the seat and lift the seat against the
front seats. Tension wheels
4 located under each
of the rear seats are used to keep the
seats folded down.
Unhook the tension wheel from ring 5
and hook it to the rods on the headrest
in front.
To return the seats
Unhook retainer 4 from the headrest
rods, and stow it by hooking it into
ring 5. Lower the seat until it is approxi -
mately 10 cm from the floor then re -
lease it. The seat positions itself under
its own weight. Raise the seatback and
ensure the seat is correctly locked.
When moving the rear
seats, ensure that nothing
obstructs the anchorage
points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
When tilting the seats, be
careful not to lock the seat
belts. If this happens, tilt
the seat again. Pull the belt
strap, reposition the seat and re -
lease the strap.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
When refitting the seat -
back , make sure it is cor -
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
3
2
1
4
5

rear bench seat..................................... (up to the end of the DU)
3.32
ENG_UD24500_4
Banquette arrière : fonctionnalité (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Rear bench seat: functions
The seat and the seatback may be
folded away to allow large objects to be
transported.
To raise the seatBefore handling the bench seat, ensure
the seat belt catches 1 are attached
to the corresponding buckles 2 and
ensure the front seats are far enough
forward.
From the front, lift the seat base 3
against the front seats (movement A).
To fold away the seat, proceed in reverse order.
Position the rear bench seat cushion in
such a way so as to position the rear
section of the seat base under the seat-
back.
Check that it is correctly locked in po -
sition.
To fold down the seatbackFrom the luggage compartment, pull
straps 4 either side of the bench seat,
and lower the seatback.
To raise the seatback, proceed in reverse order.
Refit the seatback and click it back into
place.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
REAR BENCh SEAT: functions
When moving the bench
seat, ensure that the seat
belt catches are correctly
locked in position.
When the bench seat has been put
back in place, make sure that it is
correctly locked and the seat belts
are correctly repositioned.
When refitting the seat -
back , make sure it is cor -
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
When moving the rear
seats, ensure that nothing
obstructs the anchorage
points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
A
3
2
44
1

transporting objectsin the luggage compartment ........... (up to the end of the DU)
towing rings ........................................................... (current page)
3.37
ENG_UD24509_4
Transport d objets dans le coffre (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Transporting objects in the boot
TRANSPoRTINg oBJECTS IN ThE luggAgE CoMPARTMENT
Always place the objects to be trans -
ported so that their largest side rests
against the back of the rear bench
seat, for normal loads (Example A), or
against the back of the front seats when
the rear bench seatbacks are folded
down, as with maximum loads (exam -
ple B).
Always position the heavi -
est items directly on the
floor. Use the lashing points
on the floor of the luggage
compartment, if these are fitted to
the vehicle. The luggage should be
loaded in such a way that no items
will be thrown forward and strike the
occupants if the driver has to brake
suddenly. Fasten the rear seat belts,
even if the seats are not occupied.
locations for anchorage
points
(depending on the vehicle)
These are for securing items trans -
p o r t e d i n th e l u g g a g e c o m p a r t -
ment (refer to the information on
“Transporting objects in the luggage
compartment”).
AB

maintenance:interior trim ....................................................... (current page)
4.15
ENG_UD22508_5
Entretien des garnitures intérieures (X44 - Renault)
ENG_NU_952-4_X44_Renault_4
Interior trim maintenance
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will have a
longer service life. It is therefore ad -
visable to maintain the vehicle interior
regularly.
Stains should always be dealt with
quickly. Whatever type of stain is on
the trim, use soapy water (if possible,
warm water) containing:
Do not use detergents (washing up
liquid, powdered products, alcohol -
based products, etc.).
Use a soft cloth.
Glass instrument panel(e.g.: instrument panel, clock, exterior
temperature display, radio display).
Use a soft cloth or cotton wool.
If this does not clean it properly, use a
soft cloth (or cotton wool) slightly mois-
tened with soapy water and then wipe
clean with a soft damp cloth or cotton
wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco -
hol must not be used under any cir-
cumstances.
Seat belts
These must be kept clean.
Use products selected by our Technical
Department (Approved outlets) or
warm, soapy water and a sponge and
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
Fabrics (seats, door trim,
etc.)
Dust fabrics regularly.
Liquid stains
Use soapy water. Absorb or dab lightly
(never rub) using a soft cloth, then rinse
and absorb the excess water.
Solid or thick stains
Remove any excess solid or thick ma-
terial immediately and carefully using
a spatula (from the edge inwards to
avoid spreading the stain).
Clean using the procedure for a liquid
stain.
Special instructions for sweets or
chewing gum
Put an ice cube on the stain to solidify
it, then proceed as for a solid stain.
For advice on interior maintenance
and/or on unsatisfactory results,
contact an approved dealer.