ABS RENAULT TWINGO RS 2009 2.G Chasiss ESP User Guide

38C-63
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF193
PRESENT
OR
STOREDINJ. MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Even though it is stored in the computer, the ABS/ESP system is not faulty.
The ESP is deactivated following unusable information from the injection system.
Perform fault finding on the injection system using the diagnostic tool.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP.
Note:
Once the fault in the injection system has been repaired, clear the ABS/ESP computer
fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the injection computer (see 13B, Diesel injection or 17B, Petrol injection) using the diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF193

38C-68
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF313
PRESENT
OR
STOREDINVALID SEQUENTIAL GEARBOX MULTIPLEX SIGNALS
NOTESSpecial notes:
The ABS/ESP system is not faulty, but has received unusable signals from the BVR.
Perform fault finding on the BVR using the diagnostic tool.
Note:
Once the fault in the sequential gearbox system has been repaired, clear the ABS/ESP
computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Run a check on the BVR using the diagnostic tool (see 21B, Sequential gearbox).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF313

38C-69
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF321
PRESENT
OR
STOREDCLUTCH SWITCH SIGNAL CONSISTENCY
DEF: Inoperative
NOTESSpecial notes:
The ABS/ESP system is not faulty.
Perform fault finding on the injection system using the diagnostic tool.
Note:
Once the fault in the INJECTION system has been repaired, clear the ABS/ESP
computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when driving after having exceeded a speed of 42 mph
(70 km/h).
Check the injection computer (see 13B, Diesel injection or 17B, Petrol injection) using the diagnostic tool.
ESP_V05_DF321

38C-78
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$150.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
Tool command Diagnostic tool title Comments
RZ001Fault memory This command is used for clearing the computer's stored faults
RZ011Sensor offsetsThis command reinitialises programming of the ESP sensors.
Run this command each time an operation required the steering
wheel angle to be programmed or following any operation on the
axle assemblies.
Also run this command when the combined sensor has been
removed or replaced
SC001Check target teethThis command tests the condition of the teeth on each wheel.
Select the command SC001 and follow the instructions.
The test result should indicate 48 teeth.
SC006Bleed the hydraulic unit and
brake circuitsThis command should only be used if an abnormally long brake
pedal travel is noted during a road test with ABS control (the
system must have been bled beforehand by the usual method).
Select command SC006 and follow the instructions given by the
diagnostic tool.
AC003Front left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC004Front right-hand wheel
solenoid valvesSee the interpretation of command (see Interpretation of
commands).
AC005Rear left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC006Rear right-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC013Wheel speed sensor supply
testSee the interpretation of command (see Interpretation of
commands).
AC016Pump motor testSee the interpretation of command (see Interpretation of
commands).
AC187Brake light activation relaySee the interpretation of command (see Interpretation of
commands).
AC195Vehicle speed signalSee the interpretation of command (see Interpretation of
commands).
AC196Hazard warning light activation
requestSee the interpretation of command (see Interpretation of
commands).
ANTI-LOCK BRAKING SYSTEM
Fault finding – Command summary table

38C-85V3 MR-413-X44-38C050$170.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
NOTESOnly check the customer complaint after performing a full check with the
diagnostic tool.
FAULTS DETECTED ON BRAKING WITH ABS/BRAKING REGULATION
Locking of one or more wheels ALP2
PullALP3
DriftALP4
Unexpected ABS operation at low speed and with slight pedal pressure ALP5
Unexpected ABS operation on a poor road surface ALP6
Unexpected ABS operation when using special equipment (car phone, CB, etc.) ALP7
Lengthening of the brake pedal travel following a regulation phase (with an
irregular pedal when entering the regulation phase)ALP8
Spongy pedalALP9
Brake pedal vibrationALP10
Noises from the pump, the pipes or the hydraulic unit ALP11
ANTI-LOCK BRAKING SYSTEM
Fault finding – Customer complaints

38C-86V3 MR-413-X44-38C050$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Customer complaints38C
Bosch 8.1 ESP
Vdiag No.: 05
OTHER CASES
No dialogue with the ABS computer ALP1
ESP computer not detected during the multiplex network test on CLIP ALP12
Illumination of brake lights ALP 13
Unexpected ABS operation at low speeds and slight pedal pressure ALP14
Intermittent illumination of brake, ESP, ABS, SERVICE and STOP warning lights
and the message "Brake failure" on the instrument panel with no fault codes in
the computerALP15

38C-87
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP1 No dialogue with the ABS/ESP computer
NOTESOnly address this customer complaint after a complete check with the diagnostic tool.
Use the Wiring Diagram Technical Note for New Twingo.
Try to establish dialogue with an ESP computer on another vehicle to make sure that the diagnostic tool is not
faulty. If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle,
the cause could be a faulty computer interfering on the multiplex network.
Check the tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
Check that the power supply to the diagnostic socket is correct:
Check for + 12 V on connection BP19 of component 225.
Check for earth on connections MAM and NAM of component 225.
If the connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Apply the fault finding procedure for specification 1. DEF of fault DF001 Computer supply.
Carry out fault finding on the multiplex network using the diagnostic tool (see 88B, Multiplexing).
If dialogue has still not been established after these checks, contact Techline.
ESP_V05_ALP1
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart

38C-88
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP2 Locking or braking of one or more wheels
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check the conformity of the mechanical components (see MR 411, Mechanical,
30A, General information, Brake, Specifications).
REMINDERLocking of wheels on a vehicle fitted with ABS or squealing of the tyres, which feels like
locking to the customer, may be linked to normal operation of the system and should not
always be considered a fault.
Braking with ABS regulation on very poor roads can cause significant squealing.
However, if the wheel(s) is/are actually locking, lift the vehicle in order to be able to rotate the wheels and check:
Possible inversion when connecting the speed sensors.
Use parameters PR001 Front right-hand wheel speed, PR002 Front left-hand wheel speed, PR003 Rear right-
hand wheel speed and PR004 Rear left-hand wheel speed whilst slowly turning the wheels in question and
checking the consistency of the results obtained.
If the value measured is zero, rotate the other wheels to confirm an electrical inversion of the sensors and repair
the wiring harness.
If a single reading is incorrect:
–Check that the sensor casing is secured when rotating.
–Check that the wheel speed sensor mounting is in good condition.
–If that is unsuccessful, replace the corresponding sensor and repeat the check procedure (see MR 411
Mechanical, 38C, Anti-lock braking system, Wheel speed sensor: Removal - Refitting).
–A possible inversion of the pipes on the hydraulic unit (see MR 411, Mechanical, 38C, Anti-lock braking
system, Hydraulic braking unit, List and location of components).
Run commands AC003 Front left-hand wheel solenoid valves, AC004 Front right-hand wheel solenoid
valves, AC005 Rear left-hand wheel solenoid valves and AC006 Rear right-hand wheel solenoid valves while
depressing the brake pedal and check for locking/unlocking cycles on the wheel concerned (see Dealing with
command modes).
If the cycles are not detected on the wheel tested (wheel remains locked), check if they occur on another wheel
(confirmation of a reversal after a repair, see MR 411, Mechanical, 38C, Hydraulic braking unit, List and
location of components).
If the cycles are not detected on a wheel and the pipes have not been inverted, replace component 1094
(see MR 411, Mechanical, 38C, Hydraulic braking unit, Removal- Refitting).
Check that the sensor holder does not rotate (depending on fitting).
Check the quality of the mounting of the wheel speed sensors (correct clipping for the front wheels).
Check the conformity of the targets: the condition and the number of teeth= 48 (using the command SC001
"Check target teeth").
Replace if necessary.
If the fault is still present after these checks, replace component 1094 (see MR 411, Mechanical, 38C, Hydraulic
braking unit, Removal- Refitting).
ESP_V05_ALP2

38C-89
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP3 Pull
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check the conformity of the mechanical components (see MR 411, Mechanical,
30A, General information, Brake, Specifications).
Disconnect one wheel speed sensor.
Start the engine and check that only the ABS
and ESP fault warning lights are lit.
Is the brake fault warning light also lit?Do not drive, the "braking compensator" function
cannot be carried out (risk of a spin).
Deal first with the faults using the diagnostic tool.
Drive the vehicle and operate the brakes.
Is the customer complaint still present
under these conditions?If the brake pedal travel is comparatively long, bleed
the brake circuit (see MR 411, Mechanical, 30A,
General information, Brake circuit, Bleeding).
If the travel is normal, check that the 4 vehicle tyres
are identical and in accordance with the
manufacturer's recommendations (see MR 411,
Mechanical, 35A, Wheels and tyres, Tyre, Tyre
pressure, Identification and Tyre, Identification).
Check and adjust the wheel alignment (see MR 411,
Mechanical, 30A, General information, Front
axle, Adjustment).
Check for any leaks on the brake circuit.
Apply the fault finding procedure described in the ALP 2
"Locking of one or several wheels".
YES
NO
YES
NO
ESP_V05_ALP3

38C-90
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$180.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Fault finding chart38C
Bosch 8.1 ESP
Vdiag No.: 05
ALP4 Drift
NOTESOnly address this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor.
Start the engine and check that only the ABS
and ESP fault warning lights are lit.
Is the brake fault warning light also lit?Do not drive, the "braking compensator" function
cannot be carried out (risk of a spin).
Deal first with the faults using the diagnostic tool.
Drive the vehicle and operate the brakes.
Is the customer complaint still present
under these conditions?It is a road holding fault not related to the ABS/ESP
system.
Check the condition and conformity of the front and
rear brake linings.
Check that the 4 vehicle tyres are identical and in
accordance with the manufacturer's
recommendations (see MR 411, Mechanical, 35A,
Wheels and tyres, Tyre pressure, Identification
and Tyres, Identification).
Check that the pressures of the 4 tyres conform to
the manufacturer's recommendations (see MR 411,
Mechanical, 35A, Wheels and tyres, Tyre
pressure, Identification).
Check and adjust the wheel alignment (see MR 411,
Mechanical, 30A, General information, Front
axle, Adjustment).
Normal behaviour linked to the system operation during the
regulation phase, mainly on surfaces with uneven grip or
which are poorly laid.
YES
NO
YES
NO
ESP_V05_ALP4