engine RENAULT TWINGO RS 2009 2.G Chasiss ESP User Guide

38C-48
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF098
PRESENT
OR
STOREDNO UCH MULTIPLEX SIGNAL
NOTESSpecial notes:
Even though this is stored in the computer, this fault does not cause the warning lights
to come on or a fault message, because the ESP system is not faulty.
Perform fault finding on the UCH (Passenger compartment connection unit) using
the diagnostic tool.
Note:
After repairing the fault in the UCH (Passenger compartment connection unit),
clear the fault memory in the ESP system.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the UCH (Passenger compartment connection unit) using the diagnostic tool (see 87B, Passenger
compartment connection unit).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF098

38C-52
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
If the fault appears while the vehicle is being driven on a steep gradient, during a very
tight turn or while the vehicle is being transported on a lorry, train, boat etc., with the
engine running, clear the fault and test drive, if possible, to check that the fault does
not return.
Conditions for applying fault finding procedures to stored faults:
The fault is declared present after a road test.
Check that component 1175 is fitted and attached correctly (the arrow indicating the front of the vehicle).
Check the conformity of the tyres (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres: Identification
and Tyre pressure, Identification).
Check the axle assembly geometry (see MR 411, Mechanical, Chassis, Front axle adjustment).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations
and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offset.
Re-establish dialogue with the ABS/ESP computer, and if no other fault is to be dealt with, clear the computer fault
memory.
Carry out a road test.
If the fault is still present, contact the Techline.
ESP_V05_DF126

38C-55
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF186
PRESENT
OR
STOREDNO INSTRUMENT PANEL MULTIPLEX SIGNAL
NOTESNote:
When the fault in the instrument panel has been repaired, clear the ESP fault
memory.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the instrument panel using the diagnostic tool (see 83A, Instrument panel).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF186

38C-63
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF193
PRESENT
OR
STOREDINJ. MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Even though it is stored in the computer, the ABS/ESP system is not faulty.
The ESP is deactivated following unusable information from the injection system.
Perform fault finding on the injection system using the diagnostic tool.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP.
Note:
Once the fault in the injection system has been repaired, clear the ABS/ESP computer
fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the injection computer (see 13B, Diesel injection or 17B, Petrol injection) using the diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF193

38C-64
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF202
PRESENT
OR
STOREDUCH MULTIPLEX SIGNALS DISABLED
DEF: Reverse gear signal consistency
NOTESSpecial notes:
Even though this is stored in the computer, this fault does not cause the warning lights
to come on or a fault message, because the ESP system is not faulty.
Perform fault finding on the UCH (Passenger compartment connection unit) using the
diagnostic tool.
Note:
After repairing the fault in the UCH (Passenger compartment connection unit), clear the
fault memory in the ESP system.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Run a check on the UCH (Passenger compartment connection unit) using the diagnostic tool (see 87B,
Passenger compartment connection unit).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF202

38C-66
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF300
PRESENT
OR
STOREDPUMP MOTOR CONTROL CIRCUIT
DEF: Abnormal voltage.
NOTESUse the Wiring Diagram Technical Note for New Twingo.
Check the tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
Check the condition and position of fuse F1 (40A) and F2 (30A) in the engine fuse box
(see 81C, Fuse box).
Check the connection and condition (possible wiring damage) of the connectors of components 1094, 1834,
1016 and intermediate connector R107.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
With the connector of component 1094 disconnected, check the insulation and continuity of connections MAH
of component 1094 (tightness, oxidation, etc.).
Connectors of components 1094, 1175, 583 and intermediate union R107 disconnected,
–check the insulation and continuity of connection AP5 between component 1094 and intermediate
connector R107.
–Check the insulation and continuity of connection AP5 between intermediate connector R107 and
component 1016.
–Check the insulation and continuity of connection BP14 between components 1094 and 1834.
–Check the insulation and continuity of connection BP8 between components 1094 and 1834.
If the connections are faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
ESP_V05_DF300

38C-67
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF311
PRESENT
OR
STOREDNO SEQUENTIAL GEARBOX MULTIPLEX SIGNAL
NOTESSpecial notes:
Even though it is stored in the computer, this fault does not cause the warning light to
come on or a fault message, because the ESP system is not faulty.
Perform fault finding on the BVR (sequential gearbox) using the diagnostic tool.
Note:
After repairing the fault in the BVR (sequential gearbox), clear the fault memory in the
ESP system.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Run a check on the BVR using the diagnostic tool (see 21B, Sequential gearbox).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF311

38C-68
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF313
PRESENT
OR
STOREDINVALID SEQUENTIAL GEARBOX MULTIPLEX SIGNALS
NOTESSpecial notes:
The ABS/ESP system is not faulty, but has received unusable signals from the BVR.
Perform fault finding on the BVR using the diagnostic tool.
Note:
Once the fault in the sequential gearbox system has been repaired, clear the ABS/ESP
computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Run a check on the BVR using the diagnostic tool (see 21B, Sequential gearbox).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF313

38C-79
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$160.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
AC003
AC004
AC005
AC006FRONT LEFT-HAND WHEEL SOLENOID VALVES
FRONT RIGHT-HAND WHEEL SOLENOID VALVES
REAR LEFT-HAND WHEEL SOLENOID VALVES
REAR RIGHT-HAND WHEEL SOLENOID VALVES
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
The previous four commands allow the hydraulic check of each wheel.
Raise the vehicle in order to be able to rotate the wheels, and check that they rotate freely.
Keep the brake pedal depressed to prevent the wheel being tested from being turned (do not brake so firmly that
full brake power is reached).
Select and confirm the command of the wheel being examined (e.g. Front left-hand wheel solenoid valves, etc.)
Turn the wheel concerned by hand to see it go through several locking/unlocking cycles.
ESP_V05_AC003/ESP_V05_AC004/ESP_V05_AC005/ESP_V05_AC006
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of commands

38C-80
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$160.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of commands38C
Bosch 8.1 ESP
Vdiag No.: 05
AC013WHEEL SPEED SENSOR SUPPLY TEST
NOTESConditions of use of the command.
Ignition on, engine off.
This command is used to test the supply to every wheel speed sensor.
Select command AC013 and check for 12 V between:
–connections 4T and 4S of component 150,
–connections 4H and 4G of component 151,
–connections 4E and 4C of component 153,
–connections 4N and 4M of component 152.
ESP_V05_AC013