bulb RENAULT TWINGO RS 2009 2.G Electrical Equipment - Electric Windows, Sunroof Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 54, PDF Size: 0.25 MB
Page 20 of 54
87D-20
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 4
CONTINUED
Remove the driver's window winder switch (see
MR 411 mechanical, 87D
Electric windows - Sunroof, driver's door
front window winder switch: Removal -
Refitting).
Shunt connection SPB3 to 22D and 22C on
connector of component 1512.
Using the test bulb connected to the chassis
earth, check the feeds again on connections 22D
and 22C on component 133.
Are the feeds correct?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOContinuity fault on connection 22C and 22D.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
Connect a test light between connections
22B and 22A on component 204.
Reconnect the electric window switch and
operate it. Does the test light illuminate?
YES
Replace the passenger's window winder
motor (see MR 412 bodywork, 51A, Side
opening element mechanisms, Front side
door electric window mechanism:
Removal - Refitting).
NO Continuity fault on connection 22A and 22B. If
there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
B
Page 21 of 54
87D-21
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 5 Only the driver's window does not operate at all
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged, + after ignition feed switched
on and doors closed.
Check that the fuses are sound.
Using a 21 W test bulb and a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door
front window winder switch: Removal -
Refitting) and disconnect its connector.
Shunt connection 21E to MAM to lower the
window (to raise it, shunt 21C to MAM) on the
connector of component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOUsing an ohmmeter, carry out a continuity
test on connection MAM between
component 1512 and the chassis earth.
Is the earth correct?
YES NO
NOCheck that earth MAM is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
Check for an earth on connection MAM of
component 203
Is the earth correct?
YES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
Page 24 of 54
87D-24
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 5 Only the driver's window does not operate at all
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged, + after ignition feed switched
on and doors closed.
Check that the fuses are sound.
Using a 21 W test bulb and a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door
front window winder switch: Removal -
Refitting) and disconnect its connector.
Shunt connection 21E to MAN to lower the
window (to raise it, shunt 21C to MAN) on the
connector of component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOUse an ohmmeter to test the continuity on
connection MAN between component 1512
and the chassis earth.
Is the earth correct?
YESNO
NOCheck that earth MAN is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
Check for earth on connection MAN of
component 203.
Is the earth correct?
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
YES
Page 30 of 54
87D-30
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 7
CONTINUED
Shunt connection SPB3 to 22D and 22C on component
connector 1512.
Using the test bulb connected to the chassis earth,
check the feeds again on connections 22D and 22C on
component 133.
Are the feeds correct?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder switch:
Removal - Refitting).
NOContinuity fault on connections 22D
and 22C. Pay close attention to the
intermediate connector. If there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Connect a test light between connections 22B and 22A
of component 204.
Reconnect the electric window switch and operate
it. Does the test light illuminate?
YES
Replace the window winder motor (see MR 412
bodywork, 51A, Side opening element
mechanisms, Front side door electric window
mechanism: Removal - Refitting).
NOContinuity fault on connection 22A and
22B. If there is a repair procedure (see
Technical Note 6015A, Repairing
electrical wiring, Wiring:
Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
B
Page 32 of 54
87D-32
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 7
CONTINUED
Shunt connection SPB3 to 22D and 22C on component
connector 1512.
Use a test light connected to the chassis earth to check
the feeds again on connections 22D and 22C on
component 133.
Are the feeds correct?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder switch:
Removal - Refitting).
NOContinuity fault on connections 22D
and 22C. Pay close attention to the
intermediate connector. If there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Connect a test bulb between connection 22B and
connection 22A on component 204.
Reconnect the electric window switch and operate
it. Does the test light illuminate?
YES
Replace the window winder motor (see MR 412
bodywork, 51A, Side opening element
mechanisms, Front side door electric window
mechanism: Removal - Refitting).
NOContinuity fault on connection 22A and
22B. If there is a repair procedure (see
Technical Note 6015A, Repairing
electrical wiring, Wiring:
Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
B
Page 33 of 54
87D-33
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 8The passenger window does not operate at all with the passenger
switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof,
passenger's door front window winder
switch:
Removal -Refitting) and disconnect its
connector.
Connect a test light to connections MAN and
22C (or 22D) of component 133.
Does the bulb light up correctly?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal - Refitting).
NOContinuity fault on connection MAN.
Check that earth MAN is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 34 of 54
87D-34
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 8The passenger window does not operate at all with the passenger
switch only
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Connect a test light to connection MAM and 22C
(or 22D) of component 133.
Does the bulb light up correctly?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal - Refitting).
NOContinuity fault on connection MAM.
Check that earth MAM is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring; if
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
Page 43 of 54
87D-43
MR-413-X44-87D000$944_eng.mif
V1
87D
ELECTRIC WINDOWS - SUNROOF
Electric sunroof - Fault finding chart
ALP 1 The sunroof does not operate at all
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a multimeter and a 21 W test bulb.
Use the diagnostic tool.
Read the configuration in the UCH and check
that configuration LC070 “One touch
window\sunroof” * is correctly configured
“with”.
Does parameter LC070 display WITH?
YES
Move the sunroof control to the “Closed”
position and press and hold the central part of
the control.
After pressing the central part of the control
for approximately 10 seconds, does the roof
move smoothly?
YES
See ALP 4.
NOModify the configuration (see 87B,
Passenger compartment connection unit).
NOCheck the feed by connecting a test light between
connections BP93 and MAM of component 1579.
Does the bulb light up correctly?
YES NO
Check the feed by connecting a test light
between connection BP93 and the chassis earth.
Does the test light work
correctly?
NO YES
Fault on connection MAM between
component 1579 and the chassis earth; be
careful of the intermediate connector R339.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. When the wiring has
been repaired, carry out the initialisation (see
Electric sunroof: Initialisation).
Fault on connection BP93 between
components 1579 and 1016; be careful of the
intermediate connectors R339 and R301.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. After the wiring has
been repaired, carry out an initialisation (see
Electric sunroof: Initialisation).
A
New Twingo
MR-413-X44-87D000$944_eng.mif