ABS RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual

83A-5
MR-413-X44-83A000$056.mif
V5
INSTRUMENT PANEL
Fault finding - Introduction

Vdiag No.: 04, 08
83A
4. FAULT FINDING PROCEDURE (CONTINUED)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to the + 12 V feed or with another wire.
If a fault is detected, repair or replace the wiring harness.

83A-9
MR-413-X44-83A000$112.mif
V5
INSTRUMENT PANEL
Fault finding - List and location of components

Vdiag No.: 04, 08
83A
2Warning light display:
1Brake warning light10“Service” warning light
2Major electric power-assisted steering fault
warning11
Rear fog lights indicator light
3Battery charge warning light12Front fog lights indicator light
4Oil pressure warning light13Direction indicator light
5Coolant temperature warning light14Passenger airbag disconnection warning light
6Particle filter warning light record
(Not used on the New Twingo)15Seat belt reminder indicator light
7On board diagnostics warning light16Door(s) open warning light
(Not present in the New Twingo)
8Airbag fault warning light17“Stop” warning light
9ABS warning light

83A-11
MR-413-X44-83A000$168.mif
V5
INSTRUMENT PANEL
Fault finding - Operating diagram

Vdiag No.: 04, 08
83A
Multiplex network:
Input signals: 1Instrument panel computer
2ABS or vehicle speed circuit
3Sequential gearbox
4Airbag
5Rev counter
6Injection computer
7UCH
8+ after ignition feed
9Lighting dimmer
10Fuel sender
11Trip computer scroll button
12Parking brake
13Oil pressure
14EPAS
15Brake fluid level
16Side light
17Code
18Headlight
19Front fog light
20Rear fog light
21Battery supply
22Earth
23/24Left-hand and right-hand indicators
25Clock setting buttons (on entry level version)

83A-16
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
–Illumination of the “battery charge” warning light:
Illumination of the “battery charge” warning light indicates the following statuses:
●Fixed illumination for three seconds when the + after ignition feed is switched on: Warning light test
phase by the instrument panel.
●Flashing: Low voltage.
If the “Stop” warning light and “Battery charge” warning light come on simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “Oil pressure warning” warning light:
The “Oil pressure warning” warning light always comes on with the “Stop” warning light and the “Stop” buzzer
sounds. This warning light indicates a pressure fault in the engine lubrication circuit and indicates potential engine
damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “Coolant temperature warning” warning light:
The “coolant temperature warning” warning light always comes on with the “Stop” warning light and the “Stop”
buzzer sounds. This warning light indicates that the cooling circuit temperature is too high, and there is a risk of the
engine overheating and engine damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “ABS” warning light:
Illumination of the “ABS” warning light indicates the following statuses to the driver:
–Rapid flashing: ABS not configured.
–Slow flashing: ABS in configuration phase.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
If the “Service” warning light and “ABS” warning light come on simultaneously, refer to the “Service warning light
illumination” insert.

83A-20
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
“Service” warning light + “ABS” warning light:
–ABS fault warning.
“Service” warning light + “Particle filter” warning light:
–“Major particle filter fault” warning.
The New Twingo does not currently have a particle filter.
“Service” warning light + “OBD” warning light:
–“Combustion misfire” warning.
“Service” warning light + “OBD” warning light flashing:
–“Destructive combustion misfire” warning.
“Service” warning light + “Airbag fault warning” warning light:
–“Airbag fault” warning.
“Service” warning light + “Sinusoid” warning light:
–“Minor injection fault” warning.
–“Water in diesel fuel” warning (on diesel configuration only).
–“Sequential gearbox fault” warning (on sequential gearbox configuration only).

83A-21
MR-413-X44-83A000$280.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Configuration
1. UNIT CONFIGURATIONS:
Procedure to be applied: Copy the values measured whilst reading LCXXX or consult ICM*.
2. PARAMETER SETTINGS:
*ICM (Shared World Information): available on Renault Net Configuration
reading numberConfiguration number Control Specification
LC029 CF149Gearbox type–Manual gearbox
–Sequential gearbox
LC049 CF138Type of fuel–PETROL
–DIESEL
LC051 CF140Distance unit–KM
–MILES
LC061 CF150Cruise control/speed limiter–WITH
–NONE
LC052 CF141Overspeed function - Arabia–WITH
–NONE
LC064 CF158Seat belt reminder buzzer–STATUS 1
–STATUS 2
–STATUS 3
LC011 CF038Dimmer present–YES
–NO
LC094 CF180External temperature–ABSENT
–PRESENT
LC098 CF181Electric power-assisted
steering–WITH
–NONE
LC053 CF142Electronic stability program
(ESP)–ABS/without ESP
–With ABS/ESP
–Without ABS/ESP
LC106 CF198OCS–WITH
–NONE
VP002Enter VIN
VP016Oil service and odometer
(miles-km)This command is used to enter the oil
service interval and frequency and
odometry in miles or km.
Only use this command if replacing the
instrument panel.

Vdiag No.: 04, 08
MR-413-X44-83A000$280.mif

83A-30
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fault signalET249:Service warning
light activated by
the system1-Multiplex line
communication
2- Injection
3-Water present in diesel
fuel
4-Sequential gearbox
5-Vehicle speed circuit
6-Cruise control/speed
limiter
7-ESP
8-ABS
9-Oil change interval
10- Particle filter
11- Airbag
12- OBDSee the interpretation of
ET249 SERVICE warning
light activated by the
system
Parking brake
signalET097:Parking brakeAutomatic
parking brake
onAPPLIED
In the event of a fault, consult
the interpretation of status
ET097 Parking brake Parking
brake
releasedRELEASED
Minimum brake
fluid level signalET019:Minimum brake
fluid levelMinimum
brake fluid
reservoir
levelYES
In the event of a fault, consult
the interpretation of status
ET019 Minimum brake fluid
level. Normal brake
fluid
reservoir
levelNO
Oil pressure
present signalET096:Oil pressure
contactEngine
runningOPENIn the event of a fault,
consult the interpretation of
fault DF009 “oil pressure
sensor” Engine
stoppedCLOSED

83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD

Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif

83A-35
MR-413-X44-83A000$616.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of statuses
ET004
SIDE LIGHTS SWITCH
NOTESSpecial notes:
–Only perform these tests if the statuses do not correspond with the system
programming functions.
–Side lights on.
INACTIVE
NOTESIf the status becomes “INACTIVE”, apply the following fault
finding procedure.
Check fuse F43 (10A) of the passenger compartment fuse box, component code 1016.
Check the connection and condition of the connector of component 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the + 12 V supply to connection LPG of component 247.
If the connection is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance of:
Connection LPG between component 1016 and component 247.
Connection MAN35 of component 247.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET004 / TDB_V08_ET004

Vdiag No.: 04, 08
MR-413-X44-83A000$616.mif

83A-40
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET245
INDICATORS
NOTESCheck for the absence of faults on the indicators in the UCH field before starting
fault finding.
Vehicle under + after ignition feed.
If the indicator lights are not displayed or are inconsistent with the position of the control, carry out the following
fault finding procedure.
If status ET245 INDICATORS is INACTIVE and the control is activated:
Check that the connector of component 247 is in good condition and correctly connected.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the connector, otherwise replace the wiring.
Check the continuity of:
Connection 64C between component 645 and component 247 (left-hand indicator)
Connection 64D between component 645 and component 247 (right-hand indicator)
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET245 / TDB_V08_ET245