overheating RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 66, PDF Size: 0.28 MB
Page 16 of 66
83A-16
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
–Illumination of the “battery charge” warning light:
Illumination of the “battery charge” warning light indicates the following statuses:
●Fixed illumination for three seconds when the + after ignition feed is switched on: Warning light test
phase by the instrument panel.
●Flashing: Low voltage.
If the “Stop” warning light and “Battery charge” warning light come on simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “Oil pressure warning” warning light:
The “Oil pressure warning” warning light always comes on with the “Stop” warning light and the “Stop” buzzer
sounds. This warning light indicates a pressure fault in the engine lubrication circuit and indicates potential engine
damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “Coolant temperature warning” warning light:
The “coolant temperature warning” warning light always comes on with the “Stop” warning light and the “Stop”
buzzer sounds. This warning light indicates that the cooling circuit temperature is too high, and there is a risk of the
engine overheating and engine damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “ABS” warning light:
Illumination of the “ABS” warning light indicates the following statuses to the driver:
–Rapid flashing: ABS not configured.
–Slow flashing: ABS in configuration phase.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
If the “Service” warning light and “ABS” warning light come on simultaneously, refer to the “Service warning light
illumination” insert.
Page 18 of 66
83A-18
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
–Illumination of the “Sinusoid” warning light:
Illumination of the “Sinusoid” warning light indicates the following statuses to the driver:
●Fixed illumination 3 seconds after + after ignition feed: Test phase by the instrument panel.
●Fixed illumination (If sequential gearbox configuration): Sequential gearbox overheating warning.
●Fixed illumination + buzzer (If sequential gearbox configuration): Increased sequential gearbox
overheating warning.
●Water in diesel fuel warning.
●Level 1 injection fault.
If the “Service” warning light and “Sinusoid” warning light come on simultaneously, refer to the “Service warning light
illumination” insert.
–Illumination of the “Stop” warning light:
Illumination of the “Stop” warning light alone characterises a warning light test phase by the instrument panel.
Outside of this condition, the “Stop” warning light is always associated with a “Stop” buzzer and another warning light
to indicate a fault.
“Stop” warning light + “Stop” buzzer:
–Major injection fault warning.
“Stop” warning light + “Stop” buzzer + “Brake” warning light:
–Brake circuit fault.
–Electronic Braking Distribution fault.
“Stop” warning light + “Stop” buzzer + “Battery charge” warning light:
–Battery charge warning.
“Stop” warning light + “Stop” buzzer + “Oil pressure warning” warning light:
–Oil pressure warning.
“Stop” warning light + “Stop” buzzer + “Coolant temperature warning” warning light:
–Coolant temperature warning.
“Stop” warning light + “Stop” buzzer + “Major electric power-assisted steering fault warning” warning light:
–Major electric power-assisted steering fault warning.