RENAULT TWINGO RS 2009 2.G Electrical Equipment - Lightening Service Manual
Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 44, PDF Size: 0.24 MB
Page 41 of 44

80D-41
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 10 Lights not switching on at night
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
The engine must be running in order for the automatic lighting function to operate and
the system must be equipped with a rain/light sensor.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" in the UCH. Check that the following faults are not present:
–DF011 "Rain/light sensor circuit",
–DF135 "Rain sensor",
–DF136 "Light sensor".
Deal with the above faults if they are present.
Note:
The sensor requests the lights to be switched on when there is poor light intensity (at night, in a tunnel, etc.).
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Activate the automatic lighting function by switching
the side lights on and off twice in succession:
a beep will sound to confirm this.
Did a beep sound?
YES
NORefer to the interpretation of status ET081
"Lighting stalk position".
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP10
Page 42 of 44

80D-42
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 10
CONTINUED
If the vehicle is fitted with a rain/light sensor, check that the vehicle is configured with a rain/light sensor.
Check that LC044 "Rain/light sensor" displays "Present". If not, carry out CF035 "Rain/light sensor".
Check that LC096 "Automatic wiper function" displays "With". If not, carry out CF194 "Automatic wiper
function".
Check that LC095 "Automatic lighting function", displays "With". If not, carry out CF193 "Automatic
headlight function".
Check that status ET142 Engine operating
phase is RUNNING.
Is status ET142 RUNNING?
YES
Check that the windscreen is clean and in good condition (no cracks, bonded correctly, etc.).
Check that the sensor is present and correctly positioned.
Check that the windscreen is the correct type.
NORun fault finding on the multiplex network and
the injection computer. (see 88B,
Multiplexing and 13B, Diesel injection or
17B, Petrol injection)
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 43 of 44

80D-43
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 11 No See-me-home lighting
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Check that LC025 "See-me-home lighting" is "With", otherwise use CF032 "See-me-home lighting".
Check that the ignition is switched off.
Flash the headlights one or more times (as required) to activate the See-me-home lighting function.
Check that the horn and lights switch is operating correctly using status ET081 "Lighting stalk position". In the
event of a fault with the horn and lights switch, refer to the interpretation of status ET081 "Lighting stalk
position".
Use the following commands to check that the side lights, dipped headlights and main beam headlights are
operating correctly.
–AC055 "Side lights",
–AC054 "Dipped headlights",
–AC062 "Main beam headlights".
In the event of a fault, refer to the interpretation of the following faults:
–DF087 "Side lights relay control circuit",
–DF088 "Dipped headlights relay control circuit",
–DF098 "Main beam headlights relay control circuit".
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP11
Page 44 of 44

80D-44
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 12 No courtesy lights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check that fault DF139 "Courtesy lights" is not present. Deal with the fault if it is
present.
Check the conformity of status ET463 "Door(s) or tailgate" (see 87B, Passenger compartment connection
unit).
Check that LC121 "Gradual lighting and dimming of the courtesy lights" is "With", otherwise use CF031
"Calibration".
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP12