air condition RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R01-08 User Guide

86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < X < 15 V).
Note:
Apply this fault finding method if the fault reappears as present after having been
cleared
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
•for New Twingo: F48 (15A),
•for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R108_VA4_DF039

86A-41
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF040
DF043
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF: No communication with the CD changer
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct if necessary, using SC002 Computer configuration.
Look for any signs of damage to the wiring harness, check the condition and connection of the connectors and
connections of components 261 and the CD changer.
If the connectors or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector or the wiring, otherwise replace
the wiring.
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the checks are correct, replace the CD changer.
If the fault persists, contact your Techline.
R108_VA4_DF040/R108_VA4_DF043

86A-43
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF055
PRESENT
OR
STOREDBUTTON JAMMED
1.DEF: Radio front panel button jammed.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
The button concerned is pressed for at least 2 minutes,
Check the conformity of the radio buttons by consulting the following statuses:
–ET005 Source button,
–ET007 Info traffic button,
–ET008 Radio on/off button,
–ET009 CD eject button,
–ET010 Radio preset button 1,
–ET011 Radio preset button 2,
–ET012 Radio preset button 3,
–ET013 Radio preset button 4,
–ET014 Radio preset button 5,
–ET015 Radio preset button 6,
–ET063 MEM button,
–ET068 Volume - button,
–ET069 Volume + button,
–ET070 OK button,
–ET071 Up button,
–ET072 Down button,
–ET073 Left-hand button,
–ET074 Right-hand button,
If the one of the statuses is Pressed, press on the corresponding button so that the status becomes Released.
If the fault is still present, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
R108_VA4_DF055

86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064

86A-48
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF081
PRESENT
OR
STOREDCD CHANGER BUTTON JAMMED
1. DEF: CD changer button jammed
NOTESNone.
Check the operation and condition of the CD changer button, using status ET009 CD eject button (see
Conformity check).
R108_VA4_DF081

86A-57
AFTER REPAIRRepeat the conformity check from the start.
V2 MR-413-X44-86A100$160.mif
RADIO
Fault finding – Interpretation of parameters86A
R01-08
Vdiag No.: A4
PR005RADIO FIELD INTENSITY
NOTESThe values shown in this conformity check are given as a guide.
Test conditions: Engine off, ignition on and radio on.
Perform the conformity check outside, in an area with good radio reception
and without obstacles.
Conformity check:
Monitor the PR005 value of the diagnostic tool data display.
Display of frequency received for the radio station currently set.
Radio field intensity parameterRadio reception level
(data display)
Outdoor testUnit: dBµV
Data interpretation:
Radio reception value Status
X > 18 dBµVCorrect radio reception
14 dBµV < X < 18 dBµVCorrect sound quality
RDS decoding (for example: display of
station names) correct
Automatic synchronisation / Presence in
the radio list
not satisfactory
10 dBµV < X < 14 dBµVCorrect sound quality
RDS decoding (for example: display of
station names) not satisfactory
Automatic synchronisation / Presence in
the radio list
not satisfactory
X > 10 dBµVRadio reception not satisfactory
If the fault is still present, contact the Techline.
R108_VA4_PR005
RADIO
Fault finding – Interpretation of parameters

86A-60
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
86A
R01-08
Vdiag No.: A4
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated and
radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R108_VA4_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-63
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 3
Check the condition and connection of the radio
computer connector, component code 261.
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Disconnect the radio computer connector,
component code 261.
Check for + 12 V and earth on the radio between
the following connections:
•BCP4 of component 261 and the MAO
(New Twingo) or MT (Clio III) earth.
Are the checks correct?
Check for + 12 V on the radio computer between
the following connections:
•BCP4 of component 261 and earth.Check the continuity, insulation and
absence of interference resistance of
connection MAO (New Twingo) or MT
(Clio III) between the radio computer,
component code 261 and the earth.
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
B
NO
YESD
NO
YES
NO
E

86A-72
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 3 The radio does not operate when the ON button is pressed
NOTESNone.
Press the ON button of the radio.
Switch on the lights
Does the radio backlighting operate?See ALP1 No dialogue with the computer.
Is the volume 0 or on pause?Increase the volume or restart play.
Is the front/rear balance set completely to
the rear speakers?Set the front/rear balance to 0.
Are the condition and connections of the
speaker connector and speaker connections
in order?Reconnect or repair the connector(s), otherwise
replace the wiring. (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair).
See ALP 10 Sound fault for a speaker or
tweeter.
NO
YES
YES
NO
YES
NO
NO
YES
R108_VA4_ALP3

86A-74
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 5 The radio control satellite does not operate or operates poorly
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Has dialogue been established with the
multimedia interface unit (Display or
multimedia connection unit)?Consult ALP 1 No dialogue with the
computer for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding charts).
Check the condition of the radio control satellite
(see 86D, Multimedia interface unit,
Conformity check).
Are the checks correct?Contact the Techline.
NO
YES
YES
NO
A
R108_VA4_ALP5