RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R2-08 Manual PDF

86A-71
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
86A
R02-08
Vdiag No.: 64
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated
and radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit, Fault
finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R208_V64_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-72
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 1
Is a navigation computer present?
Is the navigation computer recognised during
the multiplex network test?
A
NOB
YES
NOB
YES
C

86A-73
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 2
Check the continuity, insulation and absence
of interference resistance on the following
connection:
•34HU between components 261 and 1714.
If the connection is faulty and there is a
repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC between components 662 and 261,
•34GB between components 662 and 261.If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261 and
1714,
•34GB and 107W between components 261 and
1714.Replace the navigation computer,
component code 662 (see MR 392,
Mechanical, 83C, On-board telematics
system, Navigation computer:
Removal – Refitting). Are the checks correct?
Replace the radio, component code 261 (see MR
392, Mechanical, 86A, Radio, Radio: Removal -
Refitting).
C
YES
NO
YES
NO
YES
NO
YES

86A-74
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 3
Check the condition and connection of the radio
computer connector, component code 261.
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Disconnect the radio computer connector,
component code 261.
Check for + 12 V and earth on the radio between
the following connections:
•BCP4 of component 261 and the MAO
(New Twingo) or MT (Clio III) earth.
Are the checks correct?
Check for + 12 V on the radio computer between
the following connections:
•BCP4 of component 261 and earth.Check the continuity, insulation and
absence of interference resistance of
connection MAO (New Twingo) or MT
(Clio III) between the radio computer,
component code 261 and the earth.
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
B
NO
YESD
NO
YES
NO
E

86A-75
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 4
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•BCP4 between components 261 and 710,
•BP69 between components 260 and 710
(only for Clio III).
If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
E
NO

86A-76
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 5
Check the ET002 Radio on/off button of the
display or multimedia connection unit while
pressing the on/off button (see 86D,
Multimedia connection unit, Conformity
check).
Is the result of the check correct?
Check ET036 Wheel press on/off
(see Conformity check)
Is the result of the check correct?Replace the radio, component code 261
(see MR 392 (Clio III) or MR 411 (New
Twingo) Mechanical, 86A, Radio, Radio:
Removal - Refitting).
D
YES
YESF
NO
NO
YES
G

86A-77
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 6
Check the continuity, insulation and absence
of interference resistance on the following
connection:
•34HY between components 261 and 653 or
1714.If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
Replace the display, component code 653
(see MR 392 (Clio III) or MR 411 (New Twingo)
Mechanical, 86A, Radio, Display: Removal –
Refitting) or the multimedia connection unit,
component code 1714 or (see MR 392 (Clio III)
Mechanical, 83C, On-board telematics system,
Multimedia network interface
unit: Removal – Refitting).
G
YES
NO
YES

86A-78
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 7
Check the continuity, insulation and
absence of interference resistance on the
following connection:
•34HU between components 261 and 653.If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the wiring, otherwise replace it.
Is the result of the check correct?
Is a navigation computer present in the
vehicle?
Check the insulation, continuity and
absence of interference resistance on the
following connections:
•107X between components 662 and 1714,
•107W between components 662 and 1714.If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
F
YES
NO
YES
NOI
YES
NO
YES
H

86A-79
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 8
Check the insulation, continuity and
absence of interference resistance on the
following connections:
•34GC between components 662 and 261,
•34GB between components 662 and 261.If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
H
YES
NO
YES
J

86A-80
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 9
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261
and 1714,
•34GB and 107W between components 261
and 1714.Replace the navigation computer,
component code 662 (see MR 392
(Clio III) Mechanical, 83C, On-board
telematics system, Navigation
computer: Removal – Refitting). Are the checks correct?
Replace the radio, component code 261 (see MR
392, Mechanical, 86A, Radio, Radio: Removal -
Refitting).
Is the fault still present?The problem disappears.
Replace the multimedia connection unit, component
code 1714 (see MR 392, Mechanical, 83C, On-
board telematics system, Multimedia network
interface unit: Removal - Refitting).
J
YES
NO
YES
NO
YES