key RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R2-08 Workshop Manual

86A-2V1 MR-413-X44-86A150$010.mif
86A
R2-08
Vdiag No.: 64
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu - Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Fault finding procedure
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:Vehicle(s): Clio III / New TwingoComputer name: R2-08
Function concerned: RadioVDIAG No.: 64
Special tooling required
Diagnostic tool
Multimeter
Elé. 1681 Universal bornier
For vehicles with key-operated/radio frequency remote control, use the key to switch on the ignition.
For vehicles with Renault cards,
–with the vehicle card in the card reader,
–press and hold the start button (longer than 5 seconds) with start-up conditions not fulfilled,
connect the diagnostic tool and perform the required operations.
R208_V64_PRELI
RADIO
Fault finding – Introduction

86A-3V1 MR-413-X44-86A150$010.mif
RADIO
Fault finding – Introduction86A
R2-08
Vdiag No.: 64
To cut off the + after ignition feed, proceed as follows:
Faults
Faults are declared either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of the faults should be taken into consideration when the diagnostic tool is used after
the + after ignition feed has been activated (without any of the system components being activated).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the Notes section.
If the fault is confirmed when the instructions are applied, the fault is present. Deal with the fault.
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors on these lines (corrosion, bent pins, etc.),
–the resistance of the faulty component,
–the condition of the wires (melted or cut insulation, wear). For vehicles with radio frequency remote control/key, use the key to switch off the ignition.
For vehicles with Renault cards,
Press the Start button twice briefly (less than 3 seconds),
Ensure that the + after ignition feed has been cut off by checking that the computer warning lights on the
instrument panel have gone out.

86A-28V1 MR-413-X44-86A150$070.mif
86A
R2-08
Vdiag No.: 64
The pre-code is recovered by consulting ID007 Radio programming key using the diagnostic tool or by removing
the radio and noting the four characters on the barcode following the letter T (see photo below).
There are three ways to recover the radio code (4 digits):
1. Only the VIN is available: connect to code management on Renault.Net and enter the VIN. The code server
gives the original radio code entered in the World Vehicle Database (BVM).
If the code has not been entered in the BVM or is incorrect when the code is entered in the radio, follow the
procedure below:
2.The pre-code is available: go back to code management on Renault.Net, enter the pre-code and obtain the radio
code.
If this code is correct, the radio will operate again; if not, follow the procedure below:
3. On Renault.Net, write a help message to be sent to the assistance unit.
WHEN REPLACING PARTS, OR FOR AN UNKNOWN VIN, WRITE A HELP MESSAGE IN CODE
MANAGEMENT ON RENAULT.NET TO UPDATE THE DATABASE.
RADIO
Fault finding – Anti-theft code recovery procedure

86A-49
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Excess voltage
2.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < battery voltage < 15 V).
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
–for New Twingo: F48 (15A),
–for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R208_V64_DF039

86A-51
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF046
PRESENT
OR
STOREDUNIT LOCKED
1.DEF: System locked
NOTESThis fault is detected when the radio computer receives a radio programming key
(supplied from the VIN) that is invalid for the instrument panel via the multiplex network.
Use the diagnostic tool to check that the V.I.N. of the radio is identical to that of the instrument panel.
Configure the multimedia connection unit (see 86D, Multimedia connection unit, Configuration).
Enter the radio code (see Anti-theft code).
If the fault persists, contact your Techline.
R208_V64_DF046

86A-61V1 MR-413-X44-86A150$130.mif
RADIO
Fault finding – Conformity check86A
R2-08
Vdiag No.: 64
FUNCTION: MULTIMEDIA
SUB-FUNCTION: AUDIO
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Audio testAC004:Test right front
speaker line
This command is used to
successively activate
each speaker.In the event of an
inconsistency, consult the
interpretation of fault DF001
Front right-hand speaker.
AC005:Test left front
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF002
Front left-hand speaker.
AC006:Test right rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF003
Rear right-hand speaker.
AC007:Test left rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF004
Rear left-hand speaker.
Microphone testAC010:Microphone testThis command is for
testing microphone
operation.
NOTE:
Test in a quiet place.
Command AC010 is
inactive if the auxiliary
source is selected.
Example: presence of
a USB key.In the event of an
inconsistency, consult the
interpretation of fault DF056
Microphone.