warning RENAULT TWINGO RS 2009 2.G Electrical Equipment Owner's Guide

88A-16
WIRING HARNESS
Engine wiring: Removal - Refitting
K9K
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the engine cover,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
aRemove:
-the bolts (1) ,
-the cover to the engine compartment connection
unit.II - REMOVAL OPERATION FOR PART
CONCERNED
a IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
121212
WARNING
To prevent any risk of noise, premature wear,
shor t circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.

88A-19
WIRING HARNESS
Engine wiring: Removal - Refitting
K9K
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly resistor connec-
tor,
-the engine cooling fan assembly connector.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the reversing lights switch connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the air inlet temperature sensor connector,-the exhaust gas recirculation solenoid valve con-
nector,
-the connector to the pre-postheating unit,
-the diesel injection computer connectors,
-the fuel rail pressure sensor connector,
-the fuel temperature sensor connector,
-the heater plugs connector,
-the injector connectors,
-the air temperature sensor connector,
-the turbocharging pressure sensor connector,
-the pinking sensor connector,
-the camshaft position sensor connector,
-the connector from the water detection sensor on
the fuel filter,
-the alternator connector,
-the oil pressure sensor connector.
aRefit:
-the engine compartment connection unit supply wi-
ring nut,
-the wiring mounting nut on the battery protection
fuse board,
-the battery protection fuse wiring nuts,
-the earth wiring nut on the front left-hand side
member,
-the positive battery terminal wiring nut,
-the engine earth wiring nut,
-the starter supply and earth terminal nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture), WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING

88A-21
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F, and 780
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the engine cover,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) .
aRemove:
-the bolts (1) ,
-the cover to the engine compartment connection
unit.II - REMOVAL OPERATION FOR PART
CONCERNED
a IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
121212
WARNING
To prevent any risk of noise, premature wear,
shor t circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.

88A-24
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F, and 780
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATION OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the connectors to the petrol injection computer,
-the reversing lights switch connector,
-the downstream oxygen sensor connector,
-the turbocharger solenoid valve connector,-the ignition coil connector,
-the motorised throttle valve connector,
-the turbocharger pressure sensor connector,
-the air temperature sensor connector,
-the pinking sensor connector,
-the alternator connector,
-the oil pressure sensor connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the engine harness/injection wiring connector,
-the oil vapour recirculation hose reheater connec-
tor,
-the air inlet pressure sensor connector,
-upstream oxygen sensor connector,
-the fuel vapour absorber connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) , WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING

88A-26
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the engine cover,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) .
aRemove:
-the bolts (1) ,
-the engine compartment connection unit cover.II - REMOVAL OPERATION FOR PART
CONCERNED
a IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
121212
WARNING
To prevent any risk of noise, premature wear,
shor t circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.

88A-29
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).

88A-33
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor,
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector.
aConnect:
-the engine harness/front of engine wiring connec-
tor,-the connectors to the petrol injection computer,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the motorised throttle valve connector,
-the air inlet pressure sensor connector,
-the pinking sensor connector,
-the air inlet temperature sensor connector,
-the engine harness/injection wiring connector,
-the alternator connector,
-the radio interference suppressor connector,
-the reversing lights switch connector,
-the downstream oxygen sensor connector,
-upstream oxygen sensor connector,
-the ignition coil connector,
-the fuel vapour absorber connector,
-the oil pressure sensor connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRefit the engine harness. WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
D7F
STANDARD HEATING
AIR CONDITIONING
D4F

88A-36
WIRING HARNESS
Engine wiring: Removal - Refitting
EQ UIPMENT LEVEL SPORT
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aSwitch off the ignition.
aRemove:
-the engine undertray,
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the left-hand headlight (see 80B, Headlights,
Halogen headlight: Removal - Refitting, page
80B-7) ,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (12A, Fuel mixture),
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).
aRemove the air pipe at the air filter unit inlet (1) . Equipment required
indelible pencil
Diagnostic tool
Tightening torquesm
starter supply nut8 N.m
starter solenoid nut5 N.m
alter nator positive termi-
nal nut21 N.m
earth nuts on the front
left-hand side member8 N.m
earth bolt on the gear-
box44 N.m
engine compartment
connection unit supply
terminal nut12 N.m
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
WARNING
To prevent any damage to the connectors, consult
the disconnection procedures (see Connectors:
Disconnection and reconnection) (Technical
Note 6015A, 88A, Wiring).
131763

88A-37
WIRING HARNESS
Engine wiring: Removal - Refitting
EQ UIPMENT LEVEL SPORT
88A
aRemove:
-the bolts (2) from the engine compartment connec-
tion unit cover,-the cover to the engine compartment connection
unit.
aRemove the injection computer tamperproof panel
from the injection computer mounting.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a
aDisconnect the connectors from: - the camshaft position sensor (4) ,
121212
RIGHT-HAND DRIVE
WARNING
To prevent any risk of noise, premature wear,
shor t circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
140655

88A-39
WIRING HARNESS
Engine wiring: Removal - Refitting
EQ UIPMENT LEVEL SPORT
88A
aUnlock the engine wiring/front of engine wiring con-
nector (31) (R67).
aDisconnect the engine wiring/front of engine wiring
connector (31) (R67).
aRemove:
-the nut (32) of the engine compartment connection
unit supply terminal,
-the fuse holder assembly (33) of the engine com-
partment connection unit.aRemove:
-the engine compartment connection unit nuts (34) ,
-the engine wiring.
REFITTING
I - REFITTING PREPARATION OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aPosition the engine wiring starter terminals facing
the starter studs.
121213
WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
121215