ignition RENAULT TWINGO RS 2009 2.G Electrical Equipment Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 241
Page 4 of 241
Contents
82A ENGINE IMMOBILISER
Immobiliser system: List and
location of components 82A-1
Ignition switch: Removal -
Refitting 82A-3
Transponder ring: Removal -
Refitting 82A-6
Battery for remote door
locking control: Removal -
Refitting 82A-8
82B HORN
Audible warning: Removal -
Refitting 82B-1
83A INSTRUMENT PANEL
Instr ument panel: Removal -
Refitting 83A-1
Rev counter: Removal -
Refitting 83A-3
83D CRUISE CONTROL
Cruise control - speed
limiter: List and location of
components 83D-1
Switch: Removal - Refitting 83D-2
Steering wheel switch:
Removal - Refitting 83D-384A CONTROL - SIGNALS
Steering column switch
assembly: List and location
of components 84A-1
Steering column switch
assembly: Removal -
Refitting 84A-2
Screen wiper switch:
Removal - Refitting 84A-6
Signals and lighting switch:
Removal - Refitting 84A-8
Hazard warning lights and
central door control:
Removal - Refitting 84A-10
Lighting dimmer: Removal -
Refitting 84A-12
Exter ior rear view mirror
control switch: Removal -
Refitting 84A-13
Heated rear screen: Repair 84A-14
85A WIPING - WASHING
Wiping and washing: List and
location of components 85A-1
Windscreen wiper blade:
Removal - Refitting 85A-5
Windscreen wiper arm:
Removal - Refitting 85A-6
Windscreen wiper
mechanism: Removal -
Refitting 85A-10
Windscreen wiper motor:
Removal - Refitting 85A-12
Rear screen wiper blade:
Removal - Refitting 85A-16
Rear screen wiper arm:
Removal - Refitting 85A-17
Rear screen wiper motor :
Removal - Refitting 85A-19
Rain and light sensor:
Removal - Refitting 85A-20
Page 8 of 241
80A-2
BATTERY
Battery: Removal - Refitting
80A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.aRemove the battery cover (1) . Tightening torquesm
battery bracket bolt12 N.m
positive battery terminal
nut8 N.m
stud nut on the positive
battery ter minal12 N.m
negative battery termi-
nal nut8 N.m
stud nut on the nega-
tive battery ter minal6 N.m
IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 80A, Battery, Battery: Precautions for
the repair, page 80A-1) .
WARNING
Before disconnecting the battery:
-wait until the fan assembly stops,
-wait for the computer to finish saving (1
minute).
WARNING
The visual indicator cannot be considered relia-
ble in After-Sales; do not use it to determine the
state of the battery.
119368
Page 15 of 241
80B-3
HEADLIGHTS
Halogen bulb: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
1 - Indicator bulb
aDisconnect the indicator connector.
aTurn the indicator bulb mounting a quarter of a turn
anti-clockwise (1) .
aRemove:
-the indicator "bulb mounting - bulb" assembly,
-the bulb from its mounting.2 - Side light bulbs
aRemove the cover (2) .
aDisconnect the side light connector.
aRemove:
-the "bulb mounting - bulb" assembly (3) from the
side light,
-the bulb from its mounting.
119377
119377
121386
Page 19 of 241
80B-7
HEADLIGHTS
Halogen headlight: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the bolts (1) from the halogen headlight.
aRemove the halogen headlight.
119376
119375
Page 28 of 241
81A-3
REAR LIGHTING
Rear wing light: Removal - Refitting
81A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
aDisconnect the connector (1) from the rear light on
the wing.
aRemove:
-the bolt (2) from the rear light on the wing,
-the rear light on the wing,
-the rear light bulbs on the wing (see 81A, Rear li-
ghting, Rear light bulb: Removal - Refitting,
page 81A-4) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the rear light bulbs on the wing (see 81A, Rear li-
ghting, Rear light bulb: Removal - Refitting,
page 81A-4) ,
-the rear light on the wing,
-the rear light bolt on the wing.
aConnect the connector for the rear light on the wing.
119533
Page 29 of 241
81A-4
REAR LIGHTING
Rear light bulb: Removal - Refitting
81A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
1 - Rear light bulbs on the wing
aRemove the rear light on the wing (see 81A, Rear li-
ghting, Rear wing light: Removal - Refitting, page
81A-3) .
2 - High level brake light bulb
aRemove the high level brake light (see 81A, Rear li-
ghting, 3rd brake light: Removal - Refitting, page
81A-6) .
3 - License plate light bulb
aRemove the license plate light (see 81A, Rear li-
ghting, Number plate light: Removal - Refitting,
page 81A-8) .
II - REMOVAL OPERATION FOR PART
CONCERNED
1 - Rear light bulbs on the wing
aUnclip the plate by pressing on the clips (1) .aRemove:
-the side light and brake light bulb (2) ,
-the indicator bulb (3) ,
-the rear fog light bulb (left rear light) or the rever-
sing light bulb (right rear light) (4) .
2 - High level brake light bulb
aRemove the high level brake light bulb (5) .
119535
119536
119534
Page 33 of 241
81A-8
REAR LIGHTING
Number plate light: Removal - Refitting
81A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
aUnclip the license plate lights at (1) with a small flat-
blade screwdriver.
aDisconnect the license plate light connectors.
aRemove the license plate light bulbs (see 81A, Rear
lighting, Rear light bulb: Removal - Refitting,
page 81A-4) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit the license plate light bulbs (see 81A, Rear li-
ghting, Rear light bulb: Removal - Refitting, page
81A-4) .
aConnect the number plate light connectors.
aClip on the number plate lights.
121082
Page 41 of 241
82A-1
ENGINE IMMOBILISER
Immobiliser system: List and location of components82A
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - UCH2 - Key
3 - Ignition switch No. Description
(1) UCH
(2) Key
(3) Ignition switch
(4) Antenna/Transponder ring
119507
107733
119490
Page 43 of 241
82A-3
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSet the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and pre-
tensioners, Fault finding - Replacement of com-
ponents).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .
aRemove:
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6)
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aMake a saw mark on the shear bolt.
aRemove the bolt (1) .
aLoosen the connector at (2) .
aDisconnect the starter switch connector. Equipment required
Diagnostic tool
ENGINE REV COUNTER
119489
119490
Page 44 of 241
82A-4
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
aPosition the ignition key between the first and se-
cond position (+ accessories and + after ignition
feed) (3) .
aPress the retaining lug (4) .
aRemove the ignition switch.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the ignition switch bolt,
-the steering wheel bolt.
II - REFITTING OPERATION FOR PART
CONCERNED
aaPosition the ignition key between the first and se-
cond position (+Accessories and +APC) (5) .
aPress the retaining lug (6) .
aFit the ignition switch.
aTighten the shear bolt (7) until the bolt head shears
off.
aConnect the starter switch connector.
aLock the starter switch connector.
108441
Note:
To protect against tampering, always secure the
ignition switch with a shear bolt.
Be sure to recover the sheared-off part of the
bolt after it has been tightened.
108441
119491